Search Results

There has been a substantial increase in the use of advanced high strength steel (AHSS) in automotive structures in the last few years. The usage of these materials is projected to grow significantly in the next 5-10 years with the introduction of new safety and fuel economy regulations. AHSS are gaining popularity due to their superior mechanical properties and use in parts for weight savings potential, as compared to mild steels. These new materials pose significant manufacturing challenges, particularly for welding and stamping. Proper understanding of the weldability of these materials is critical for successful application on future vehicle programs. Due to the high strength nature of AHSS materials, higher weld forces and longer weld times are often needed to weld these advanced strength steels.

With the increasing demand for safety, energy saving and emission reduction, Advanced High Strength Steels (AHSS) have become very attractive steels for automobile makers. The usage of AHSS steels is projected to grow significantly in the next 5-10 years with new safety and fuel economy regulations. These new steels have significant manufacturing challenges, particularly for welding and stamping. Welding of AHSS remains one of the technical challenges in the successful application of AHSS in automobile structures due to heat-affected zones (HAZ) at the weld joint. In this study Gas Metal Arc Welding (GMAW) of a lap joint configuration consisting of 1.0 mm Usibor® 1500 steel to uncoated Dual Phase 780 (DP780) steel was investigated. The objective of the study was to understand the wire feed rate (WFR) and torch (or robot) travel speed (TTS) influence on lap joint tensile strength.

To reach safety, emissions, and cost objectives, manufacturers of automotive body structural and chassis components shape thin gauge, high strength steel tube with a bending, pre-forming and hydroforming process. Challenging grades and bend severity require a careful optimization of the bending procedure. A joint project between Ford and ArcelorMittal Tubular Products investigated suitable bending parameters for severe bends using commercially available thin-walled DP780 and HSLA350 tubes. This paper summarizes the measurement methods found to be capable of capturing small differences in bending formability and details the influence of bender variables such as boost, pressure die, center-line bend radius and bend angle on the wrinkling, thinning and springback of these tubes. As a result of this work, recommendations were made as to effective bender set-ups for these tubes.

Gas Metal Arc Welding (GMAW) is commonly used in the automotive industry for joining heavier gauge mild and High Strength Low Alloy (HSLA) uncoated steels, where it is recognized for its versatility and speed. The only constraints typically encountered relate to fatigue performance of the joint as a result of poor design or manufacturing fit-up. Advanced High Strength Steels (AHSS), now being considered for more and more applications, however, do not offer the same ease of welding and process control is significantly more critical. They differ from mild steels in chemical composition and thermal processing, resulting in a different microstructure; designed with a richer metallurgy to have higher strength at equivalent thickness. As a result, the sensitivity to heat input is greater and the process window in which acceptable welds can be achieved is narrower.

Fuel economy and federal safety regulations are driving automotive companies to use Dual Phase and other Advanced High Strength Steels (AHSS) in vehicle body structures. Joining and assembly plays a crucial role in the selection of these steels. Specifications are available for the resistance spot welding (RSW) of lower strength sheet steels, covering many aspects of the welding process from the stabilization procedure to endurance testing. Currently, specifications in the automotive industry for RSW with AHSS are limited. It is well known that welding of a thickness ratio greater than 1:2 poses a challenge. To utilize thinner gauge AHSS panels on body-in-white, welding schedules to join the thin to thick sheet steel stack-up are needed. Most of the existing published work was conducted on uncoated sheets and welded to the same thickness.

There has been a substantial increase in the use of advanced high strength steel in automotive structures in the last few years. The usage of these materials is projected to grow significantly in the next 5–10 years with new safety and fuel economy regulations. These new materials have significant manufacturing challenges, particularly for welding and stamping. Proper understanding of the weldability of these materials is critical for successful application in future vehicle programs. This paper presents our production experience in use of DP600. Development work on the effect of weld tips on button size, and shrinkage voids due to different welding variables is discussed. The paper also provides recommendations from the current experimental knowledge base for applications on higher grades of steel (DP780 and beyond).

Gas Metal Arc Welding (GMAW) is used in the automotive industry, for joining heavier gauge mild and HSLA steels, where it is recognized for its versatility and speed. The only constraints typically encountered relate to fatigue performance of the joint as a result of poor design or manufacturing fit-up. Advanced High Strength Steels, however, do not offer the same ease of welding, and process control is significantly more critical. The process window represents the range of acceptable process parameters, primarily heat inputs, to achieve an acceptable weld; which is a measure of the robustness of the process. AHSS differ from mild steels in chemical composition and thermal processing, resulting in a different microstructure; designed with a richer chemistry to have higher strength at equivalent thickness compared to mild steels. As a result, the sensitivity to heat input is greater and AHSS has a narrower process window in which acceptable welds can be achieved.