Search Results

This paper presents an experimental study on a 2-stroke SI engine, used on small portable tools for gardening or agriculture, aimed to identify possible correlations between parameters related to ionization current and air/fuel mixture richness, considering different fuels and spark plug wear. This, to realize a simple system to control the engine parameters and adapt them to engine aging and fuel type changing. The engine was fed with commercial gasoline, low octane number gasoline, alkylate gasoline and a blend of 80% gasoline and 20% ethanol. In all tests carried out with varying engine speed and spark advance the ionization signal was characterized by a single peak, resulting in the impossibility of distinguishing chemical and thermal ionization. All data collected were analyzed looking for correlations between all the available data of CO emissions and several characteristic parameters obtained from the ionization signal.

Downsizing by turbo charging is a current approach for the reduction of fuel consumption of Spark Ignition (SI) engines. For downsized engines compression ratio has to be set as high as possible to achieve substantial gains in thermodynamic efficiency. Unfortunately, the possibility to take full advantages offered by downsizing is limited by knock phenomenon, which imposes constraints both on supercharging and compression ratios. Quasi-dimensional and multidimensional simulation can play a role of increasing importance for the design and the optimization of future engine prototypes more and more based on advanced combustion concepts, provided that well proven tools for knock simulation may be available.

In this work the authors present a model to simulate the in-cylinder pressure oscillations due to knock. Pressure oscillations are predicted by the explicit integration of a Partial Differential Wave Equation (PDWE) similar, in its structure, to the so-called “Equation of Telegraphy”. This equation differs mainly from the classical wave formulation for the presence of a loss term. The general solution of such equation is obtained by the Fourier method of variables separation. The integration space is a cylindrical acoustic cavity whose volume is evaluated at the knock onset. The integration constants are derived from the boundary and initial conditions. A novel approach is proposed to derive the initial condition for the derivative of the oscillating component of pressure. It descends, conceptually, from the integration of the linearized relation between the derivative of pressure versus time and the expansion velocity of burned gas.

Idle Speed Control plays a crucial role to reduce fuel consumption that turns in both a direct economic benefit for customers and CO\d reduction particularly important to tackle the progressive global environmental warming. Typically, control strategies available in the automotive literature solve the idle speed control problem acting both on the throttle position and the spark advance, while the Air-Fuel Ratio (AFR), that strongly affects the indicated engine torque, is kept at the stoichiometric value for the sake of emission reduction. Gasoline Direct Injection (GDI) engines, working lean and equipped with proper mechanisms to reduce NOx emissions, overcome this limitation allowing the AFR to be used for the idle speed regulation.

The use of Variable Valve Actuation (VVA) systems offers many advantages in terms of increased engine power, reduced fuel consumption and pollutant emissions, accomplishing a significant improvement of the global efficiency of the engine. In the last decade different devices have been proposed to implement advanced and innovative VVA managements on four-stroke engines. ElectroMechanical Valve Actuator (EMVA) formed by two opposite magnets and two balanced springs seem to be a very promising solution among several camless actuation systems. This type of valve actuator is characterized by highly nonlinear and strongly coupled dynamics which makes very difficult to govern engine valve motion during the last part of the closing and opening strokes, where an unstable behavior is exhibited. In this regard the control problem of the EMVA is tackled in this paper.

A system for both ignition and ion current measurement was designed and set up at Istituto Motori. Particular attention was paid to the problem of dissipating the residual energy stored in the ignition coil, reducing the electromagnetic interferences and especially improving the response of the measurement system. In order to assess the capability of the ion current signal to give reliable and accurate information for knock detection, a number of tests were carried out at full load on a commercial PFI four cylinder engine, at various air/fuel ratios and spark timings. Some knock indices based on the ionization signal, both band pass filtered and non-filtered, were introduced, in particular: the Amplitude of the Second Ionization Peak (ASIP), the Mean not filtered Ionization Current signal (MIC), the Maximum Amplitude of Ionization Current signal Oscillation (MAICO), the Integral of Modulus of filtered Ionization Current signal Oscillation (IMICO).

The work relates to the use of multidimensional modelling as a tool for improving the robustness of combustion of a Gasoline Direct Injection (GDI) Spark Ignition (SI) engine. A procedure is assessed for the prediction of the thermo-fluid-dynamic processes occurring in a single-cylinder, four-stroke engine, characterised by a bore-to-stroke ratio close to the unity, and a pent-roof head with four valves. The engine is at a design stage, under development for application on two wheels vehicles. A new generation six-holes Bosch injector is considered as realising a jet guided combustion mode. This last is preferred for its potential in realising effective charge stratification and great combustion stability under various operating conditions. The three-dimensional (3D) numerical model is developed within the AVL FIRE™ software environment.

In automotive industry the Electronic Throttle Body (ETB) plays a crucial role in drive-by-wire operations since it controls the incoming air into the engine and so the produced torque. This implies the performances of the vehicle in terms of traction, emissions, idle speed regime, cold starting management, thermal transient and smoother movement during tip/in tip/out, strongly depends on the precise control of this device [17]. Despite its apparent simplicity, the behavior of the ETB is affected by many nonlinearities and uncertain parameters which can dramatically alter its dynamics. In order to cope the unwanted nonlinear phenomenons (stick-slip motion, hysteresis, hunting, impact, caos), sophisticated model based control strategies and compensators are proposed in the literature. A time consuming identification parameters of the throttle is fundamental for these approaches and it is the main drawback for their application.

Several methods have been proposed to use pressure signal for air/fuel ratio estimation, knock detection and optimal spark timing selection. In this paper some of these methods were compared, and their accuracy and effectiveness was checked. In order to avoid the misleading effects of measurement errors, the comparison was performed using a database of test conditions obtained by means of the WAVE code (Ricardo). New correlations physically based were introduced to evaluate the trapped air mass and the Exhaust Gas Recycling (EGR), cylinder per cylinder. These correlations can give a very important contribution to balance the air-fuel ratio in each cylinder and to improve EGR control strategies.

The electromechanical devices proposed in technical literature are very flexible. However, their working principle (fixed lift, fixed lifting time and variable valve events) imposes the use of different strategies, such as cylinder or port deactivation to enable work at partial loads. This happens in particular at low loads. The present paper aims to evaluate the effect of the design and of the strategies adopted to vary the load (cylinder or port deactivation etc) on performance and on pollutant formation of a stoichiometric DISI engine. The calculations were performed by a commercial one-dimensional code (Wave produced by Ricardo). This tool was also used to give inputs to the design of the electromechanical actuator. The electromechanical design of the actuator was carried out with the aid of the code Flux2D produced by Cedrat. This code allows the complete simulation of transients and of the electrical losses of the actuator.

A number of Variable Valve Actuators (VVA) has been recently proposed to improve the performances and the part load efficiency of spark ignition engines. Due to their peculiarity, these systems work with different strategies (late or early inlet valve closing, reduced lift etc.). The shape and the timing of the valve lift affect not only the pumping losses, but also air motion inside the cylinder. That influences mixture formation and combustion evolution of Direct Injection Spark Ignition (DISI) engines. The present paper compares the performances of different VVA systems with the aid of a 1D code for the simulation of the inlet and of the exhaust phases, and of a fluid-dynamic 3D code to evaluate mixing phenomena inside the cylinder.

A simple model of combustion and pollutant formation has been set up. It is part of an engine simulator to be used for the study of engine control strategies. The calculation of inlet and exhaust phases is performed by an emptying and filling method, based on the knowledge of mean inlet and exhaust conditions. A single zone thermodynamic model has been utilized for the calculation of the combustion phase. The values of the shape factors of heat release patterns have been modeled to take into account air/fuel ratio, EGR, load and turbulence at ignition starting. Crevice storage of unburned mixture has been considered as the dominant mechanism for unburned HC production. A model for mixing and burning of HC inside the cylinder has been proposed. NO is calculated using the three steps Zeldovich approach. The model produces realistic calculations of combustion pressure and pollutants emission at various speed, load, ignition timing and EGR.