Search Results

Early implementations of direct injection technology were primarily adaptations of fuel systems to existing loop scavenge carbureted engines that did not leverage the strong interaction between the scavenge flow and fuel distribution in the cylinder. Emissions reduction techniques have been limited to engine calibration strategies using injection timing to minimize lost fuel at the expense of mixture preparation and power. This work focuses on manipulating the scavenging pattern to reduce lost fuel while improving mixture preparation and trapped oxygen. The project goals were to design an intake porting specifically for a 3.4 liter V6 2-stroke DI outboard engine that meets EPA 3 star NTE emissions regulations while increasing power by 10 percent and increasing fuel economy 10 percent over production baseline.

In pursuit of reducing dependencies on foreign oil coupled with U.S. renewable fuel standards and an overall focus and interest in greenhouse gas emissions, investigations continue on feasibility of replacement biologically derived fuels such as ethanol and butanol. Majority of existing recreational products such as marine outboard engines, boats, personal watercraft, all terrain vehicles and snowmobiles are carbureted or operate open-loop, meaning the engine does not have the capability to sense air-fuel ratio. Ethanol has a specific energy content that is less than gasoline. Without means to compensate for air-fuel ratio requirements of specific fuels, open-loop engines may suffer from a condition known as enleanment, in which catastrophic engine failure may result. On the contrary, butanol has specific energy content closer to that of gasoline, suggesting open-loop engines may be less prone to negative effects of increased biologically derived fuel concentrations in gasoline.

The University of Idaho's (UI's) entry into the 2007 SAE Clean Snowmobile Challenge (CSC) was a third-generation gasoline direct-injection (GDI) two-stroke powered snowmobile. The modulated and battery-less direct-injection system fully met the competition goals of “improved emissions and noise while maintaining or improving the performance characteristics of the original snowmobile.” The students designed and manufactured a new head for a stock two-stroke 600cc snowmobile engine. The head was designed to use direct fuel injection to control fuel quantity and timing to reduce fuel short-circuiting. Performance was refined through the use of precise engine mapping. The emissions output was further reduced by a reduction catalyst located in the exhaust silencer. Noise from the engine compartment was reduced by using sound absorbing materials and a sealed hood. The UICSC team consisted of students from freshmen through graduate students.

Gasoline direct injection (GDI) two-stroke engine technology has been developed for use in snowmobile applications. Applying GDI to a two-stroke engine significantly reduces emissions of unburned hydrocarbons and improves fuel economy by reducing the short circuiting of fuel that occurs in conventional carbureted two-stroke engines. The GDI design allows for two different modes of combustion, stratified and homogeneous. Stratified combustion is typically used during idle and light to moderate loads at low engine speeds while homogeneous combustion is used at moderate to high loads and medium to high engine speeds. This work presents the process and results of determining which mode of combustion provides better fuel economy during cruise point operation, and where the transition from stratified to homogeneous combustion should occur in snowmobile operation.

With the recent advancement in gasoline direct-injection technology for lightweight and high-specific power two-stoke engines, turbocharging a small crank-case scavenged GDI engine promises to be an effective way of increasing engine performance while maintaining the lowered emissions and increased fuel economy of GDI two-stroke engines. Along with increasing the power density, a variable geometry turbocharger should allow for an increase in low engine speed engine performance that will allow the engine to be operated at lower engine speeds providing quieter operation and decreased engine wear. Also presented is a method to increase throttle response and increase low speed torque through the use of a reed valve installed in the intake plenum.

The University of Idaho's entry into the 2006 SAE Clean Snowmobile Challenge (CSC) was a second-generation gasoline direct-injection (GDI) two-stroke powered snowmobile. A modulated and battery-less direct-injection system was used to decrease exhaust emissions and improve fuel economy without reducing the power output of the engine. The team added a reduction catalyst designed for a two-stroke to the exhaust silencer to further reduce exhaust emissions and noise. Under-hood noise was targeted by using sound absorbing materials and a sealed hood. Chassis noise was addressed by using a spray-on rubberized material that absorbs vibrations transferred through the chassis. The snowmobile entered into the 2006 SAE CSC competition was lightweight, easy-to-ride, powerful, fuel efficient, and had reduced exhaust emissions.