Search Results

Oxygen enriched air (EA) is a well known industrial mixture in which the content of oxygen is higher respect the atmospheric one, in the range 22-35%. Oxygen EA can be obtained by desorption from water, taking advantage of the higher oxygen solubility in water compared to the nitrogen one, since the Henry constants of this two gases are different. The production of EA by this new approach was already studied by experimental runs and theoretical considerations. New results using salt water are reported. EA promoted combustion is considered as one of the most interesting technologies to improve the performance in diesel engines and to simultaneously control and reduce pollution. This paper explores, by means of 3-dimensional computational fluid dynamics simulations, the effects of EA on the performance and exhaust emissions of a high-speed direct-injection diesel engine.

The paper presents a numerical study aimed at converting a commercial lightweight 2-Stroke Indirect Injection (IDI) Diesel aircraft engine to Direct Injection(DI). First, a CFD-1D model of the IDI engine was built and calibrated against experiments at the dynamometer bench. This model is the baseline for the comparison between the IDI and the DI combustion systems. The DI chamber design was supported by extensive 3D-CFD simulations, using a customized version of the KIVA-3V code. Once a satisfactory combustion system was identified, its heat release and wall transfer patterns were entered in the CFD-1D model, and a comparison between the IDI and the DI engine was performed, considering the same Air-Fuel Ratio limit. It was found that the DI combustion system yields several advantages: better take-off performance (higher power output), lower fuel consumption at cruise conditions, improved altitude performance, reduced cooling requirements.

The paper presents the development and validation of phenomenological predictive schemes for quasi-dimensional modeling of pollutant emissions in direct injected Diesel engines. Models for nitric oxide (NO), carbon monoxide (CO), as well as soot and unburned hydrocarbons (HC) have been developed. All of them have been implemented into a DI Diesel engine simulation environment, previously developed by the authors, which features quasi-dimensional modeling of spray injection and evolution, air-fuel mixture formation, as well as auto-ignition and combustion. An extended Zel'dovich mechanism, which takes into account the three main, thermal-NO formation chemical reactions has been developed for predicting NO emissions.

In this paper a detailed analysis focused on lumped parameters numerical modeling of high speed direct injected internal combustion engine cooling systems is presented and discussed. More in details, the cooling systems here studied are characterized by extreme performance, both in terms of circulating flow rates and thermal loads. First of all, a comprehensive description of the simulation environment properly tailored for cooling systems modeling is introduced and all its geometric, fluid-dynamic and thermodynamic characteristics are described in depth. Then, the model has been validated through an exhaustive numerical vs. experimental comparison, involving both cold and hot engine operation, for a wide range of rotational speeds. The general good accordance obtained between calculated and measured results clearly demonstrate the reliability of the numerical model.

In the present automotive research, increasing efforts are being directed to improve the overall organic efficiency, which, inter alia, means to improve the operational behavior of the auxiliary organs. This paper reports an experimental approach for the determination and analysis of the pressure distribution in a variable displacement vane pump for high speed internal combustion engine lubrication. More in details, an actual application is presented for a seven-blades variable displacement vane pump equipped with a hydraulic geometry variation system. This unit is characterized by a high performance, in terms of rotational speed, delivery pressure and displacement variation. The experimental layout and some relevant facilities are described. An extended test campaign was performed on the pump to characterize its operational behavior.

In this paper a detailed analysis focused on lumped parameters numerical modeling of a variable displacement vane pump for high speed internal combustion engine lubrication is presented and discussed. This particular volumetric unit is characterized by very extreme performance, both in terms of rotational speed, delivery pressure and displacement variation. First of all, a comprehensive description of the simulation environment properly tailored for the numerical modeling of the vane pump operation is introduced and all its geometric, kinematic and fluid-dynamic characteristics are described in depth. Then, the results coming from an exhaustive experimental campaign have been compared with simulations, finding a general good accordance that demonstrates the reliability of this numerical approach.

In this paper a detailed analysis focused on lumped parameters numerical modeling of a variable displacement vane pump for high speed internal combustion engine lubrication is presented and discussed. This particular volumetric unit is characterized by very extreme performance, both in terms of rotational speed, delivery pressure and displacement variation. First of all, a comprehensive description of the simulation environment properly tailored for the numerical modeling of the vane pump operation is introduced and all its geometric, kinematic and fluid-dynamic characteristics are described in depth. Then, the results coming from an exhaustive experimental campaign have been compared with simulations, finding a general good accordance that demonstrates the reliability of this numerical approach.

The Department of Mechanical and Civil Engineering (DIMeC) of the University of Modena and Reggio Emilia is developing a new type of small capacity HSDI 2-Stroke Diesel engine, featuring a specifically designed combustion system. The present paper is focused on the analysis of the combustion process, investigated by means of a customized version of the KIVA-3V code. A four stroke automobile Diesel engine featuring a very close bore size is taken as a reference, for both the numerical models calibration and for a comparison with the 2-Stroke engine. Such a comparison clearly demonstrates the effectiveness of the two stroke concept in terms of emissions reduction and high power density.

This paper studies the proportional directional control valves design influence on the energetic behavior of a mid-power compact excavator. In particular, with reference to the hydraulic circuit actuating the primary workgroup, in the paper the hydraulic power metering performed with the boom cylinder proportional control valve is studied, and some design solution useful in reducing both the hydraulic power dissipation, and the power absorption from the machinery prime mover are highlighted. The analysis, experimentally performed for different operating conditions, is carried out highlighting the influence of a metering configuration both on the supply pressure modulation and on the flow-rate supplied to the actuator.

In this paper a lumped parameters numerical model is reviewed to study the meshing process of external gear pumps and motors, with the aim of highlighting the influence of some geometrical design parameters and operating conditions on inter-teeth volumes pressures. The inter-teeth space is modeled adopting a two-volume approach, properly tailored both for the pump and for the motor units behavior description. In both cases, the communications between the interconnected inter-teeth volumes and the high and low pressure ports are sketched as variable equivalent turbulent restrictors; flow areas have been determined as functions of the gears and of the meshing grooves main design parameters. The inter-teeth pressures, and the leakage flows, are calculated solving the incompressible and isothermal continuity equation, contemporarily applied to both volumes and properly combined with the classical turbulent orifice equation.

In this paper some design aspects related to external gear pumps balancing surfaces are studied, and some useful guidelines for designing bearing blocks balancing surfaces are suggested. In order to study bearing blocks axial balance, a numerical procedure for the determination of the pressure distribution inside the clearance bounded by gears sides and bearing blocks internal surfaces is firstly presented and applied. After, the influence of bearing blocks geometry and pump operating conditions on the widening thrust is highlighted, considering both constant and variable lateral clearance heights. Then, the computations are performed to evaluate the widening thrust variation as a function of bearing blocks relative tilt with respect to gears lateral sides, and both positive and negative bearing blocks tilts are evidenced and discussed.

This paper studies the influence of the discharge chamber geometrical parameters on the steady-state characteristics behavior of a conical seat valve having compensating profile. More in details, starting from the analysis of the experimental behavior of an actual valve showing inefficient characteristic curves, the metering openings leading to the transition from under to over compensation are individuated. Then, a 3D CFD steady-state, incompressible and isothermal analysis is involved, mainly to evidence the valve discharge coefficient and flow-forces variations with operating conditions. After, two alternative valve configurations, presenting a low pressure region designed to optimize the flow-forces compensation, are characterized through the 3D CFD analysis.

The paper investigates, by means of a 3D, steady-state, incompressible and isothermal CFD analysis, the influence of the notch shape and number on proportional directional control valves metering edge characteristics. The numerical activity is firstly performed for a sharp metering edge, considered as reference case. Then, different configurations of notched metering edges are considered, coming from the adoption of two notch geometrical shapes largely used in proportional directional control valves actual design, and from a symmetrical displacement of two, three and four notches on the spool periphery. For all the cases considered, the qualitative analysis of the internal flow field is performed in order to highlight the fluid efflux main characteristics.