Search Results

Fossil fuels such as natural gas used in engines still play the most important role worldwide despite such measures as the German energy transition which however is also exacerbating climate change as a result of carbon dioxide emissions. One way of reducing carbon dioxide emissions is the choice of energy sources and with it a more favourable chemical composition. Natural gas, for instance, which consist mainly of methane, has the highest hydrogen to carbon ratio of all hydrocarbons, which means that carbon dioxide emissions can be reduced by up to 35% when replacing diesel with natural gas. Although natural gas engines show an overall low CO2 and pollutant emissions level, methane slip due to incomplete combustion occurs, causing methane emissions with a more than 20 higher global warming potential than CO2.

The continuous pursuit of more efficient diesel engines and the stricter emission regulations with the introduction of the Real Driving Emissions test (RDE) necessitate further investigations of heating strategies and their suitability in terms of series production. Under these circumstances heating strategies of a variable valve train for a single-cylinder research diesel engine have been first simulated and then experimentally tested at the Institute of Internal Combustion Engines of the Karlsruhe Institute of Technology (KIT). By combining statistical experimental design (DoE) and 1-D gas exchange simulations, empirical DoE models for the design of suitable camshaft configurations have been established. After having performed a potential assessment, the most favorable configurations were manufactured and subsequently tested.

To this day, Diesel engines with direct injection are the most efficient internal combustion engines for passenger cars. The major challenge of these engines with a conventional Diesel combustion process is the high level of particulate matter and nitrogen oxide emissions. Diesel engines in passenger cars normally use a pilot injection strategy for NVH reasons, which influences the engine-out soot emissions negatively. The Diesel fuel of the pilot injection is still burning when the main injection takes place, so, liquid components of the main injection interact with the flame of the pilot injection. The time for mixture formation decreases and the combustion takes place under locally very rich conditions which results in high levels of soot formation. For this reason new emission level restrictions cannot be reached without modern exhaust gas aftertreatment systems, which are quite expensive and can have an impact on the gas exchange.

Rapeseed oil can be a possible substitute for fossil fuel in Diesel engines. Due to different physical properties of rapeseed oil like higher viscosity and higher compressibility compared to diesel fuel, rapeseed oil cannot be easily used in conventional Diesel engines without modifications. Especially incomplete combustion leads to deposits in the combustion chamber and higher exhaust gas emissions. These unfavorable characteristics are caused primarily by insufficient mixture preparation. The adjustment of the injection system will improve the mixture preparation and the combustion of a Diesel engine, operated with rapeseed oil. The nozzle geometry is the main parameter of the whole injection system chain to realize a better combustion process and so higher efficiency and lower exhaust gas emissions.

Diesel engines face difficult challenges with respect to engine-out emissions, efficiency and power density as the legal requirements concerning emissions and fuel consumption are constantly increasing. In general, for a diesel engine to achieve low raw emissions a well-mixed fuel-air mixture, burning at low combustion temperatures, is necessary. Highly premixed diesel combustion is a feasible way to reduce the smoke emissions to very low levels compared to conventional diesel combustion. In order to reach both, very low NOX and soot emissions, high rates of cooled EGR are necessary. With high rates of cooled EGR the NOX formation can be suppressed almost completely. This paper investigates to what extent the trade-off between emissions, fuel consumption and power of a diesel engine can be resolved by highly premixed and low temperature diesel combustion using injection nozzles with reduced injection hole diameters and high pressure fuel injection.

In this work the formation and oxidation of soot inside a direct injection spark ignition engine at different injection and ignition timing was investigated. In order to get two-dimensional data during the expansion stroke, the RAYLIX-technique was applied in the combustion chamber of an optical accessible single cylinder engine. This technique is a combination of Rayleigh-scattering, laser-induced incandescence (LII) and extinction which enables simultaneous measurements of temporally and spatially resolved soot concentration, mean particle radii and number densities. These first investigations show that the most important source for soot formation during combustion are pool fires, i.e. liquid fuel burning on the top of the piston. These pool fires were observed under almost all experimental conditions.

An important source for soot formation during the combustion of diesel engines with direct injection is the interaction of liquid fuel or a very rich air/fuel-mixture with the flame. This effect appears especially in modern direct injection engines where the injection is often split in a pre- and a main injection due to noise reasons. After the ignition of the pre-injected fuel a part of the main injection can interact with the flame still in liquid phase as the fuel is injected straight towards the already burning cylinder areas. This leads to high amounts of soot. The injection strategy for this experimental study overcomes this problem by separating the injections spatially and therefore on the one hand reduces the soot formation during the early stages of the combustion and on the other hand increases the soot oxidation later during the combustion. In particular an injection configuration is used which gives the degree of freedom to modify the injection in the described manner.

In this study different methods to reduce the soot emissions of Diesel engines were investigated and compared to obtain their soot reduction potential. Apart from investigations on the practically usable engine map area with so called homogeneous charge compression ignition (HCCI) combustion processes a new heterogeneous combustion processes was developed and investigated which offers significantly reduced soot emissions while still applicable in the entire engine map. For the HCCI experiments the emphasis was put on the achievable engine load range when using conventional injector nozzles which still allow a conventional heterogeneous engine operation.

Different particulate filter systems with an electrical heating for starting the filter regeneration were designed and tested to evaluate the parameters important for a successful filter and heating device layout. These results led to a new filter system with an improved electrical heating module. Particular emphasis was put on a modular design which allows a separate optimization of the different system parts with regard to function, durability and costs. In this paper the different development steps are presented. Experimental results show the performance and limitations for electrically heated particulate traps. The analysis of the experiments was done on the one hand by using data such as temperatures, pressures and exhaust gas composition during the regeneration. On the other hand the assessment of the regeneration rate was done by weighing the filter and optically with non-destructive and partly destructive methods.

The mixture formation of a direct injection HCCI engine was optimized by a new nozzle geometry in combination with a multi-pulse injection scheme. To achieve this injection strategy, a highly flexible Piezo-Common-Rail injection system was used at the single cylinder research engine (DC BR 500, compression ratio reduced to 14:1). Optical probes for local, time resolved temperature and soot concentration measurement (Two-Color-Method) were adapted. Furthermore, a camera system was applied to detect the radiation of UV light (especially emitted by OH radicals which is an important indicator of the ignition process). So, the behaviors of different fuels in regard to the combustion process have been investigated. Diesel, SMDS and mixtures of n-heptane and iso-octane were tested with various EGR ratios, boost pressures and air/fuel ratios.