Search Results

Due to the continuous electrification of vehicles, the variety of different hybrid topologies is expected to increase in the future. As the calibration of real-time capable energy management systems (EMS) is still challenging, a development framework for the EMS that is independent of the hybrid topology would simplify the overall development process of hybrid vehicles. In this paper an analytical methodology, which is used to derive a fuel-optimal, rule-based EMS for parallel hybrids, is transferred to a series topology. It is shown that the fundamental correlations can be applied universally to both parallel and series configurations. This enables the possibility to develop a real-time capable, rule-based controller for a series HEV based on maps that ensures a fuel-optimal operation. These maps provide the optimal power threshold for the activation of the auxiliary power unit and the optimal power output dependent on the driver’s power request.

The overall efficiency of hybrid electric vehicles largely depends on the design and application of its energy management system (EMS). Despite the load coordination when operating the system in a hybrid mode, the EMS accounts for state changes between the different driving modes. Whether a transition between pure electric driving and internal combustion engine (ICE) powered driving is beneficial depends, among others, on the respective operation point, the route ahead as well as on the energetic expense for the engine start itself. The latter results from a complex interaction of the powertrain components and has a tremendous impact on the efficiency and quality of EMSs. Optimization based methods such as dynamic programming serve as benchmark for the design process of rule based control strategies. In case no energetic expenses are assigned to a state change, the resulting EMS suffers from being sub-optimal regarding the fuel consumption.

The efficiency of a Hybrid Electric Vehicle (HEV) strongly depends on its implemented Energy Management Strategy (EMS) that splits the driver’s torque request onto the Internal Combustion Engine (ICE) and Electric Motor (EM). For calibrating these EMS, usually, steady-state efficiency maps of the power converters are used. These charts are mainly derived from measurements under optimal conditions. However, the efficiency of ICEs fluctuates strongly under different conditions. Among others, these fluctuations can be induced by charge air temperature, engine oil temperature or the fuel’s knock resistance. This paper proposes a new approach for predicting the impact of any external influence onto the ICE efficiency. This is done by computing the actual deviation from the optimal reference ignition timing and adjusting the result by actual oil temperature and target air-to-fuel ratio.

Fuel cells as alternative propulsion systems in vehicles can achieve higher driving ranges and shorter refueling times compared to pure battery-electric vehicles, while maintaining the local zero-emission status. However, to take advantage of pure battery electric driving, an externally rechargeable battery can be combined with a fuel cell range extender. As part of a research project, an efficient air supply system for a fuel cell range extender was developed. To this end, a 25 kW PEM fuel cell system test bench was set up. The different parameter influences of the test bench, in particular of the air supply system, were analyzed and evaluated in terms of stack/system efficiency and functionality. The control software of the test bench was specifically developed for the flexible operating parameter variation. All adjustable variables of the system (air ratio, stack temperature, pressure, etc.) were varied and evaluated at steady-state operating points.

In recent years a new combustion phenomenon called Low-Speed Pre-Ignition (LSPI) occurred, which is the most important limiting factor to exploit further downsizing potential due to the associated peak pressures and thus the huge damage potential. In the past there were already several triggers for pre-ignitions identified, whereat engine oil seems to have an important influence. Other studies have reported that detached oil droplets from the piston crevice volume lead to auto-ignition prior to spark ignition. However, wall wetting and subsequently oil dilution and changes in the oil properties by impinging fuel on the cylinder wall seem to have a significant influence in terms of accumulation and detachment of oil-fuel droplets in the combustion chamber. For this reason, the influence of test fuels with different volatility were investigated in order to verify their influence on wall wetting, detachment and pre-ignition tendency.

In recent years concern has arisen over a new combustion anomaly, which was not commonly associated with naturally aspirated engines. This phenomenon referred to as Low-Speed Pre-Ignition (LSPI), which often leads to potentially damaging peak cylinder pressures, is the most important factor limiting further downsizing and the potential CO2 benefits that it could bring. Previous studies have identified several potential triggers for pre-ignition where engine oil seems to have an important influence. Many studies [1], [2] have reported that detached oil droplets from the piston crevice volume lead to auto-ignition prior to spark ignition. Furthermore, wall wetting and subsequently oil dilution [3] and changes in the oil properties by impinging fuel on the cylinder wall seem to have a significant influence in terms of accumulation and detachment of oil-fuel droplets in the combustion chamber.

This paper focuses on the potentials of a Belt-Starter-Generator (BSG) in the context of an ultra-light vehicle prototype with a target curb weight of only 600 kg. Therefore, two hybrid approaches with a voltage level below 60 V are described and their potentials regarding electrical driving and CO2 reduction are analysed in detail. Introducing the ‘Cars Ultra-Light Technology’ (CULT) project, the holistic lightweight approach is described as a main requirement for the further hybrid investigations. In addition, a P2-hybrid structure with a 12 V BSG on the transmission input shaft enabled unique features despite the low voltage level and limited electrical power resources. The CO2 reduction for this powertrain combination is described and compared to a conventional stop start configuration. The validation process on a dynamic test rig is presented as well.

This paper describes the development of a comprehensive simulation environment for investigations of gas-dynamic processes and combustion phenomena in rotary engines, conducted by the Austrian Institute for Powertrains and Automotive Technology of the Vienna University of Technology. In this connection, proven, commercially available engine cycle calculation Software-Tools have been used. For this, a rotary engine test bench has been established. As analysis tools, in addition to the traditional acquisition of the emitted engine torque, various pressures and temperatures, the recording of the pressure profile (combustion analysis measurement system) in the combustion chamber, as well as in the intake and exhaust ports, were used. The data of the test bench were used to develop and validate the methodology for the simulation tools. The focus in this paper is the development of a CFD (computational fluid dynamics) model with the software Converge from Convergent Science, Inc.

Future legislations claim further reduction of all restricted emissions as well as the limitation of soot emissions in diesel engines. Special alternative diesel fuels that do not contain aromatic compounds, therefore, promise great potential for further reduction of HC, CO and particulate emissions. During a research project carried out at the Institute for Powertrains and Automotive Technology at the Vienna University of Technology, the potential of alternative diesel fuels was investigated using a state-of-the-art diesel engine with common rail direct injection. The testing took part using an engine test rig as well as on the chassis dynamometer test bench to demonstrate the emission levels in real life conditions. As real biofuel, pure HVO (Hydrogenated Vegetable Oil) was investigated and additionally in different blends with fossil diesel fuel.

The piston ring and cylinder liner tribosystem is very sensitive. It is a heavily loaded system with high temperature and force exposure. High demands are made on the components in this area. These facts concern not only system components, but also the engine oil which can reach up to 300°C at the inner cylinder walls. High temperatures and force cause oil aging. As a part of the combustion chamber, the piston ring-cylinder liner tribosystem is in close contact with combustion constituents. If alternative fuels like ethanol are used, the influences to this tribosystem have to be investigated. In particular, the impacts of oil aging have to be considered to avoid higher wear and damage to the engine, to assure low fuel consumption, and to extend oil change intervals. Research work on abrasion of the ring-cylinder system was aimed to gain detailed information about the effects on this tribosystem.