Search Results

Fuel film deposits on combustion chamber walls are understood to be the main source of particle emissions in GDI engines under homogenous charge operation. More precisely, the liquid film that remains on the injector tip after the end of injection is a fuel rich zone that undergoes pyrolysis reactions leading to the formation of poly-aromatic hydrocarbons (PAH) known to be the precursors of soot. The physical phenomena accompanying the fuel film deposit, evaporation, and the chemical reactions associated to the injector film are not yet fully understood and require high fidelity CFD simulations and controlled experimental campaigns in optically accessible engines. To this end, a simplified model based on physical principles is developed in this work, which couples an analytical model for liquid film formation and evaporation on the injector tip with a stochastic particle dynamics model for particle formation.

During the past decades, the Nitrogen Oxides (NOx) emission limitations have become stricter, promoting the development of after-treatment systems like Selective Catalytic Reduction (SCR) for emission reduction purposes. The Urea-Water Solution (UWS) spray characteristics can directly have an effect on the SCR efficiency. To understand the droplet breakup and mixing of the UWS with the surrounding air under different operating conditions, a computational campaign has been set up. The main objective of the present study is to recreate the spray injection process, as well as the chemical processes that the UWS spray undergoes, and to analyze the optimal injection angle to maximize the amount of ammonia generated during the injection process by means of Computational Fluid Dynamics (CFD). A Eulerian-Lagrangian framework has been employed to track the evolution of the injected droplets within a Reynolds-Averaged Navier-Stokes (RANS) turbulence formulation.

The temperature of fuel injectors can affect the flow inside nozzles and the subsequent spray and liquid films on the injector tips. These processes are known to impact fuel mixing, combustion and the formation of deposits that can cause engines to go off calibration. However, there is a lack of experimental data for the transient evolution of nozzle temperature throughout engine cycles and the effect of operating conditions on injector tip temperature. Although some measurements of engine surface temperature exist, they have relatively low temporal resolutions and cannot be applied to production injectors due to the requirement for a specialist coating which can interfere with the orifice geometry. To address this knowledge gap, we have developed a high-speed infrared imaging approach to measure the temperature of the nozzle surface inside an optical diesel engine.

Selective Catalytic Reduction stands for an effective methodology for the reduction of NOx emissions from Diesel engines and meeting current and future EURO standards. For it, the injection of Urea Water Solution (UWS) plays a major role in the process of reducing the NOx emissions. A LES approach for turbulence modelling allows to have a description of the physics which is a very useful tool in situations where experiments cannot be performed. The main objective of this study is to predict characteristics of the flow of interest inside the injector as well as spray morphology in the near field of the spray. For it, the nozzle geometry has been reconstructed from X-Ray tomography data, and an Eulerian-Eulerian approach commonly known as Mixture Model has been applied to study the liquid phase of the UWS with a LES approach for turbulence modeling. The injector unit is subjected to typical low-pressure working conditions.

In order to comply with the increasingly restrictive limits of emissions and fuel consumption, researches are focusing on improving the efficiency of combustion engines. In this area, the aging of the injector and its effect on the injection development is not entirely analyzed. In this work, the rate of injection of a diesel injector at different stages of its lifetime is analyzed. To this end, a multi-hole piezoelectric injector was employed, comparing the injection rate measured at the beginning of its lifetime to the rate provided by the injector after aging, maintaining the same boundary conditions in both measurements. Injection pressures up to 200 MPa were used throughout the experiments. The results showed that the steady-state rate of injection was lower after the injector aged. Furthermore, the injector took a longer time to close the needle and end the injection, in comparison with the measurements done at earlier stages of its lifetime.

The use of predictive models in the study of Internal Combustion Engines (ICE) allows reducing developing cost and times. However, those models are challenging due to the complex and multi-phase phenomena occurring in the combustion chamber, but also because of the different spatial and temporal scales in different components of the injection systems. This work presents a methodology to accurately simulate the spray by Discrete Droplet Models (DDM) without experimentally measuring the injector mass flow rate and/or momentum flux. Transient nozzle flow simulations are used instead to define the injection conditions of the spray model. The methodology is applied to a multi-hole Gasoline Direct injection (GDi) injector. Firstly, the DDM constant values are calibrated comparing simulation results to Diffused Back-light Illumination (DBI) experimental technique results. Secondly, transient nozzle flow simulations are carried out.

Experimental visualization of current gasoline direct injection (GDi) systems are even more complicated especially due to the proximity of spray plumes and the interaction between them. Computational simulations may provide additional information to understand the complex phenomena taking place during the injection process. Nozzle flow simulations with a Volume-of-Fluid (VOF) approach can be used not only to analyze the flow inside the nozzle, but also the first 2-5 mm of the spray. A methodology to obtain plume direction and spray angle from the simulations is presented. Results are compared to experimental data available in the literature. It is shown that plume direction is well captured by the model, whilst the uncertainty of the spray angle measurements does not allow to clearly validate the developed methodology.

The Selective Catalytic Reduction (SCR) system has great potential in reducing NOx emissions. The urea-water solution (UWS) is the preferred method on vehicles for obtaining the ammonia, the required reductant for SCR. The UWS spray is necessary to transform exhaust gas into nitrogen and water and plays an important role in the performance of this system. The UWS needs to be properly mixed with the exhaust gas coming from the engine before entering the SCR, therefore the solution must be injected in the exhaust pipe in a way that it completely vaporizes in order to reduce deposit formation and guaranteeing a proper functioning and durability of the NOx reduction system. Achieving complete vaporization of the UWS spray is not an easy task, mainly due to reduced package space. Another challenge for converting UWS to ammonia is the latent energy in the exhaust.

Most studies about common-rail diesel injection consider the fuel flow along the injector as isothermal. This hypothesis is arguable given the small diameter of the orifices along which the fuel flows, together with the expansions that take place across them. These phenomena may provoke variations in the fuel temperature, which in turn modify the fuel properties (i.e. viscosity, density, speed of sound…), thus influencing injector dynamics as well as the fuel atomization and mixing processes. The present investigation accounts for these effects by means of a 1D model for the fuel flow along a common-rail ballistic injector. Local variations of fuel temperature and pressure are considered by the model thanks to the implementation of the adiabatic flow hypothesis.

A prototype multi-hole diesel injector operating with n-heptane fuel from a high-pressure common rail system is used in a high-pressure and high-temperature test rig capable of reaching 1100 Kelvin and 150 bar under different oxygen concentrations. A novel optical set-up capable of visualizing the soot cloud evolution in the fuel jet from 30 to 85 millimeters from the nozzle exit with the high-speed color diffused back illumination technique is used as a result of the insertion of a high-pressure window in the injector holder opposite to the frontal window of the vessel. The experiments performed in this work used one wavelength provide information about physical of the soot properties, experimental results variating the operational conditions show the reduction of soot formation with an increase in injection pressure, a reduction in ambient temperature, a reduction in oxygen concentration or a reduction in ambient density.

The dense spray region in the near-field of diesel fuel injection remains an enigma. This region is difficult to interrogate with light in the visible range and difficult to model due to the rapid interaction between liquid and gas. In particular, modeling strategies that rely on Lagrangian particle tracking of droplets have struggled in this area. To better represent the strong interaction between phases, Eulerian modeling has proven particularly useful. Models built on the concept of surface area density are advantageous where primary and secondary atomization have not yet produced droplets, but rather form more complicated liquid structures. Surface area density, a more general concept than Lagrangian droplets, naturally represents liquid structures, no matter how complex. These surface area density models, however, have not been directly experimentally validated in the past due to the inability of optical methods to elucidate such a quantity.

In the present work a constant-pressure flow facility able to reach 15 MPa ambient pressure and 1000 K ambient temperature has been employed to carry out experimental studies of the combustion process at Diesel engine like conditions. The objective is to study the effect of orifice diameter on combustion parameters as lift-off length, ignition delay and flame penetration, assessing if the processing methodologies used for a reference nozzle are suitable in heavy duty applications. Accordingly, three orifice diameter were studied: a spray B nozzle, with a nominal diameter of 90 μm, and two heavy duty application nozzles (diameter of 194 μm and 228 μm respectively). Results showed that nozzle size has a substantial impact on the ignition event, affecting the premixed phase of the combustion and the ignition location. On the lift-off length, increasing the nozzle size affected the combustion morphology, thus the processing methodology had to be modified from the ECN standard methodology.

In this work a detailed soot model based on stationary flamelets is used to simulate soot emissions of a reactive Diesel spray. In order to represent soot formation and oxidation processes properly, a calibration of the soot reaction rates has to be performed. This model calibration is usually performed on basis of engine out soot measurements. Contrary to this, in this work the soot model is calibrated on local soot concentrations along the spray axis obtained from laser extinction chamber measurements. The measurements are performed with B7 certification Diesel and a series production multihole injector to obtain engine similar boundary conditions. In order to ensure that the flow and mixture field is captured well by the CFD-simulation, the simulated liquid penetration lengths and flame lift-off lengths are compared to chamber measurements.

Nowadays the main part of investigations in controlled auto-ignition (CAI) engines are centered on performance or some engine processes simulation, leaving aside particle number (PN) emission. The present work is focused on this last topic: PN emission analysis using two different injectors in a 2-stroke CAI engine, and a global comparison of PN emission of this engine with its homonymous 4-stroke engines at two operating conditions. The study was performed in a single-cylinder gasoline engine with 0.3 l displacement, equipped with an air-assisted direct-injection (DI) fuel injection system. Concerning the injectors evaluated, significant differences in PN emission have been found. When the I160X injector (narrow spray angle) was used, PN emissions were reduced. The spray cone angle during the injection event appears to be a key factor for PN emission reduction.

This paper explores the use of rate of injection (ROI) and rate of momentum (ROM) to characterize the internal flow of an ECN gasoline direct injector. Rate of momentum has been successfully used in diesel injectors with this objective and for the first time, the measurements have been made on a GDi injector. The paper focuses on the experimental setup used and the different uncertainties and difficulties to translate the typically measured diesel technique to a gasoline injector.

Proper initial conditions are essential to successfully perform a simulation, especially for highly transient problems such as Diesel spray injection. Until now, no much attention has been paid to the internal nozzle flow initialization because spray simulations are usually decoupled from the nozzle. However, new homogeneous models like Eulerian Spray Atomization (ESA) model allow to simulate the internal nozzle flow and the spray seamlessly. Therefore, the behavior of the spray for the first microseconds is highly influenced by the initial conditions inside the nozzle. Furthermore, last experiments confirm the presence of gas inside the nozzle between successive injections. This work deals with the initialization procedure in a way that mass flow rate and spray penetration curves are well predicted by the model.

The Fick's law is commonly used to model diffusion problems, but from some time ago it has been also used to model liquid jet atomization and mixing into gaseous atmosphere under certain hypothesis. An OpenFOAM computer model based on this principle has been developed and validated on axisymmetric geometries. This model has also been used to study the atomization process on the Engine Combustion Network (ECN) single-hole Spray A injector. Results have been compared to X-Ray and Mie-Scattering experimental data, showing that the Fick's law and its variants predict well the liquid core but tend to over-predict the spray angle/width in the first millimeters after the nozzle exit.

Schlieren/shadowgraphy has been adopted in the combustion research as a standard technique for tip penetration analysis of sprays under diesel-like engine conditions. When dealing with schlieren images of reacting sprays, the combustion process and the subsequent light emission from the soot within the flame have revealed both limitations as well as considerations that deserve further investigation. Seeking for answers to such concerns, the current work reports an experimental study with this imaging technique where, besides spatial filtering at the Fourier plane, both short exposure time and chromatic filtering were performed to improve the resulting schlieren image, as well as the reliability of the subsequent tip penetration measurement. The proposed methodology has reduced uncertainties caused by artificial pixel saturation (blooming).

Transients in the rate of injection (ROI) with respect to time are ever-present in direct-injection engines, even with common-rail fueling. The shape of the injection ramp-up and ramp-down affects spray penetration and mixing, particularly with multiple-injection schedules currently in practice. Ultimately, the accuracy of CFD model predictions used to optimize the combustion process depends upon the accuracy of the ROI utilized as fuel input boundary conditions. But experimental difficulties in the measurement of ROI, as well as real-world affects that change the ROI from the bench to the engine, add uncertainty that may be mistaken for weaknesses in spray modeling instead of errors in boundary conditions. In this work we use detailed, time-resolved measurements of penetration at the Spray A conditions of the Engine Combustion Network to rigorously guide the necessary ROI shape required to match penetration in jet models that allow variable rate of injection.

This publication is the result of a multidisciplinary collaboration between the academia and the industry. An attempt to pre-ionize and influence the trajectory and the fluid mechanics of the injected fuel into an experimental injection system by means of electromagnetic fields was made. This collaboration project started from research proposal, which aims at exploring the effects of a highly ionized environment on the fuel injection event and how the momentum of the injected fuel droplets may be affected by the electromagnetic fields in form of quantified variables, such as spray penetration, spreading angle and the spray axis angle. An influence of the applied electromagnetic field on the fuel spray depending on the electrode configuration was observed and is presented and discussed in this publication.