Search Results

This study investigates if particulates from a GDI engine can be significantly suppressed by use of ultra-high injection pressures under 2 different engine conditions known to be associated with high particulate numbers (PN): warm-up and transients. Experiments were carried out in a single-cylinder GDI engine equipped with an endoscope connected to a high-speed camera to enable combustion visualization. To mimic the warming-up, the coolant temperature was varied between 20 °C and 90 °C. A Diesel injector with modified nozzle was used and the injection pressures were varied between 400 and 1500 bar. The results revealed that increasing the fuel injection pressure decreased engine out HC and PN under warming-up conditions. However, the coolant water temperature was the most dominant factor affecting the emissions. For coolant temperature of 20 °C, the use of 1500 bar fuel injection pressure in comparison to lower fuel pressures resulted in significantly lower PN.

Maximum fuel injection pressures for GDI engines is expected to increase due to positive effects on emissions and engine-efficiency. Current GDI injectors have maximum operating pressures of 35 MPa, but higher injection pressures have yielded promising reductions in particle number (PN) and improved combustion stability. However, the mechanisms responsible for these effects are poorly understood, and there have been few studies on fuel sprays formed at high injection pressures. This paper summarizes experimental studies on the properties of sprays formed at high injection pressures. The results of these experiments can be used as inputs for CFD simulations and studies on combustion behavior, emissions formation, and combustion system design. The experiments were conducted using an injection rate meter and optical methods in a constant volume spray chamber. Injection rate measurements were performed to determine the injectors’ flow characteristics.

The demands for a future diesel engine in terms of emission compliance, CO2 emissions, performance and cost effectiveness set new requirements for the development process of the combustion system. This paper focuses on the development of the next generation Volvo Cars diesel combustion system, which should comply with Euro 6d including Real Driving Emissions (RDE), with emphasis on the novel methods applied throughout the process. The foundation of a high performing combustion system is formed by first determining the requirements for the system, after which the key factors that affect system performance are selected, such as the charge motion, combustion chamber geometry and injector nozzle geometry. Based on the requirements, a robust charge motion with desired flow characteristics is defined. A new automated CFD optimization process for combustion chamber geometry and spray target is developed.

Further restrictions on NOx emissions and the extension of current driving cycles for passenger car emission regulations to higher load operation in the near future (such as the US06 supplement to the FTP-75 driving cycle) requires attention to low emission combustion concepts in medium to high load regimes. One possibility to reduce NOx emissions is to increase the EGR rate. The combustion temperature-reducing effects of high EGR rates can significantly reduce NO formation, to the point where engine-out NOx emissions approach zero levels. However, engine-out soot emissions typically increase at high EGR levels, due to the reduced soot oxidation rates at reduced combustion temperatures and oxygen concentrations.

The expansion of current driving cycles for emission regulations to higher load operation in the near future (such as the US06 supplement to the FTP-75 driving cycle) requires attention to low emission combustion concepts in medium to high load regimes. One possibility to reduce NO emissions is to increase the EGR rate. The combustion-temperature reducing effects of high EGR rates can significantly reduce NO formation, to the point where engine-out NOx emissions approach zero levels. However, engine-out soot and CO emissions typically increase at high EGR levels, due to the reduced soot and CO oxidation rates at reduced combustion temperatures and oxygen concentrations. The work presented in this paper focuses on different strategies to reduce soot and CO emissions associated with EGR rates of up to 50%, at which NO formation is largely avoided, but combustion temperatures are not low enough to consider the process as Low-Temperature Combustion (LTC).

One of the problems encountered when operating Diesel engines in HCCI mode is a too early start of combustion, due to the low ignition resistance of Diesel fuels. Correct phasing of the combustion process requires a lower in-cylinder temperature during compression. One possibility of regulating the temperature is to adjust the intake valve closing timing and thus the effective compression ratio. A single cylinder research engine, configured as a passenger car type DI Common Rail Diesel engine, was fitted with a fully adjustable hydraulic valve train, which allowed free settings of the valve timing events. Premixed combustion was achieved by injecting the fuel during the compression stroke, prior to ignition, in multiple steps. Different combinations of intake valve closing timing and external EGR were tested as well as the possibility to use internal EGR for combustion control.

An experimental investigation was carried out in which an HSDI Common Rail Diesel engine was operated in both HCCI and conventional Diesel combustion modes, using conventional Diesel fuel in both cases. The engine used in the experiments was a single cylinder version of a modern passenger car engine with a displacement of 480 cc. In HCCI mode, the fuel was injected in multiple stages during the compression stroke, using a nozzle with a 60° included angle. To control the phasing and rate of combustion, the effective compression ratio was reduced by retarded intake valve closing. In addition, increased amounts of EGR were used. HCCI operation reduced soot and NOx emissions significantly. The use of a narrow included angle for conventional Diesel operation increased emissions significantly. The effect of a wider included angle and modifications to the piston were investigated experimentally and numerically.

An investigation of the possibility to extend the 3-dimensional modeling capabilities from conventional diesel to the HCCI combustion mode simulation was carried out. Experimental data was taken from a single cylinder engine operating with early injections for the HCCI and a split-injection (early pilot+main) for the high speed Diesel engine operation. To properly phase the HCCI mode in the experiments, high amounts of cooled EGR and a decreased compression ratio were used. In numerical simulation performed using KIVA3-V code, modified to incorporate the Detailed Chemistry Approach the same conditions were reproduced. Special attention is paid on the analysis of the events leading up to the auto-ignition, which was reasonably well predicted.

The possibilities of operating a direct injection Diesel engine in HCCI combustion mode with early injection of conventional Diesel fuel were investigated. In order to properly phase the combustion process in the cycle and to prevent knock, the geometric compression ratio was reduced from 17.0:1 to 13.4:1 or 11.5:1. Further control of the phasing and combustion rate was achieved with high rates of cooled EGR. The engine used for the experiments was a single cylinder version of a modern passenger car type common rail engine with a displacement of 480 cc. An injector with a small included angle was used to prevent interaction of the spray and the cylinder liner. In order to create a homogeneous mixture, the fuel was injected by multiple short injections during the compression stroke. The low knock resistance of the Diesel fuel limited the operating conditions to low loads. Compared to conventional Diesel combustion, the NOx emissions were dramatically reduced.