Search Results

The paper discusses the concept, specification and performance of a new, dedicated range extender engine for plug-in series hybrid vehicles conceived and designed by Lotus Engineering. This has been undertaken as part of a consortium project called Limo Green, part-funded by the UK government. The Lotus Range Extender engine has been conceived from the outset specifically as an engine for a plug-in series hybrid vehicle, therefore being free of some of the constraints placed on engines which have to mate to conventional, stepped mechanical transmissions. The paper starts by defining the philosophical difference between an engine for range extension and an engine for a full series hybrid vehicle, a distinction which is important with regard to how much power each type must produce. As part of this, the advantages of the sparkignition engine over the diesel are outlined.

The paper describes the principal features of Omnivore, a spark-ignition-based research engine designed to investigate the possibility of true wide-range HCCI operation on a variety of fossil and renewable liquid fuels. The engine project is part-funded jointly by the United Kingdom's Department for the Environment, Food and Rural Affairs (DEFRA) and the Department of the Environment of Northern Ireland (DoENI). The engineering team includes Lotus Engineering, Jaguar Cars, Orbital Corporation and Queen's University Belfast. The research engine so far constructed is of a typical automotive cylinder capacity and operates on an externally-scavenged version of the two-port Day 2-stroke cycle, utilising both a variable charge trapping mechanism to control both trapped charge and residual concentration and a wide-range variable compression ratio (VCR) mechanism in the cylinder head.

Omnivore is a single cylinder spark ignition based research engine conceived to maximize the operating range of auto-ignition on a variety of fossil and renewable fuels. In order to maximize auto-ignition operation, the two-stroke cycle was adopted with two independent mechanisms for control. The charge trapping valve system is incorporated as a means of varying the quantity of trapped residuals whilst a variable compression ratio mechanism is included to give independent control over the end of compression temperature. The inclusion of these two technologies allows the benefits of trapped residual gas to be maximised (to minimize NOx formation) whilst permitting variation of the onset of auto-ignition. 2000rpm and idle are the main focus of concern whilst also observing the influence of injector location. This paper describes the rational behind the engine concept and presents the results achieved at the time of writing using 98ulg and E85 fuels.

Homogeneous charge compression ignition (HCCI), combustion has the potential to be highly efficient and to produce low NOx, carbon dioxide and particulate matter emissions, but experiences problems with cold start, running at idle and producing high power density. A solution to these is to operate the engine in a ‘hybrid mode’, where the engine operates in spark ignition mode at cold start, idle and high loads and HCCI mode elsewhere during the drive cycle, demanding a seamless transition between the two modes of combustion through spark assisted controlled auto ignition. Moreover; HCCI requires considerable control to maintain consistent start of combustion and heat release rate, which has thus far limited HCCI's practical application. In order to provide a suitable control method, a feedback signal is required.

An expedient route to improving in-vehicle fuel economy in 4-stroke cycle engines is to reduce the swept volume of an engine and run it at a higher BMEP for any given output. The full-load performance of a larger capacity engine can be achieved through pressure charging. However, for maximum fuel economy, particularly at part-load, the expansion ratio, and consequently the compression ratio (CR) should be kept as high as possible. This is at odds with the requirement in pressure-charged gasoline engines to reduce the CR at higher loads due to the knock limit. In earlier work, the authors studied a pressure-charging system aimed at allowing a high CR to be maintained at all times. The operation of this type of system involves deliberately over-compressing the charge air, cooling it at the elevated pressure and temperature, and then expanding it down to the desired plenum pressure, ensuring a plenum temperature which can potentially become sub-atmospheric at full-load.

The Homogeneous Charge Compression Ignition (HCCI) engine combustion uses heat energy from trapped exhaust gases enhanced by the piston compression heating to auto ignite a premixed air/gasoline mixture. As the HCCI combustion is controlled by the charge temperature, composition and pressure, it therefore, prevents the use of a direct control mechanism such as in the spark and diesel combustion. Using a large amount of trapped residual gas (TRG), is seen as one of the ways to achieve and control HCCI in a certain operating range. By varying the amount of TRG in the fresh air/fuel mixture (inside the cylinder), the charge mixture temperature, composition and pressure can be controlled and hence, the auto ignition timing and heat release rate. The controlled auto ignition (HCCI) engine concept has the potential to be highly efficient and to produce low NOx, carbon dioxide and particulate matter emissions.

The homogeneous charge compression ignition-HCCI (also to be known as controlled auto ignition-CAI) engine concept has the potential to be highly efficient and to produce low NOx, carbon dioxide and particulate matter emissions. It experiences, however, problems with cold start, running at idle and high loads that together with controlling the combustion over the entire speed/load range limits its practical application. A solution to overcome these problems is to operate the engine in ‘hybrid mode’, where the engine operates in HCCI mode at low, medium and cruising loads and switch to spark ignition (SI) mode (or diesel mode-CI) at a cold start, idle and higher loads. To operate such ‘hybrid mode’ engine, a transition between SI and HCCI and SI modes, as a result of changes in engine speed and load must be seamless in operation, whilst keeping all relevant engine and combustion parameters in an acceptable range.

Ever increasing oil prices and emissions legislation have forced automobile manufacturers to investigate new methods and technologies to reduce fuel consumption in Spark Ignition (SI) engines. Two such technologies are Controlled Auto Ignition (CAI) and Cylinder Deactivation (CDA), both of which have the potential to decrease fuel consumption at light load. This paper presents synergies between running engines in CAI and CDA operation. A baseline simulation model of a production intent vehicle incorporating a four-cylinder engine was produced and correlated to measured test data. Experimental results of various CAI and CDA investigations have been projected onto the baseline simulation model and an analysis performed over the New European Drive Cycle (NEDC). It has been found that running an engine in CAI or CDA mode improves efficiency in explicit areas of the fuel map.

The purpose of the European « SPACE LIGHT » (Whole SPACE combustion for LIGHT duty diesel vehicles) 3-year project launched in 2001 is to research and develop an innovative Homogeneous internal mixture Charged Compression Ignition (HCCI) for passenger cars diesel engine where the combustion process can take place simultaneously in the whole SPACE of the combustion chamber while providing almost no NOx and particulates emissions. This paper presents the whole project with the main R&D tasks necessary to comply with the industrial and technical objectives of the project. The research approach adopted is briefly described. It is then followed by a detailed description of the most recent progress achieved during the tasks recently undertaken. The methodology adopted starts from the research study of the in-cylinder combustion specifications necessary to achieve HCCI combustion from experimental single cylinder engines testing in premixed charged conditions.

Controlled Auto Ignition (CAI) uses compression heat to auto ignite a homogeneous air/fuel mixture. Using internal exhaust gas recirculation (IEGR) as an indirect control method, CAI offers superior fuel economy and pollutant emission reductions. Practically, this can readily be achieved by a method of early exhaust valve closure and late inlet valve opening to trap exhaust gas residuals within the cylinder from one cycle to the next. In order to understand the combustion mechanism, we did a comprehensive investigation on CAI fuelled with iso-octane. Test data was gathered from a single cylinder research engine equipped with Lotus' Research Active Valve Train (AVT) System, and the modelling study was based on detailed chemical kinetics. It was found that CAI can only occur when the thermal energy of the engine charge, which is a mixture of air / fuel and IEGR, reaches a certain level.

ELEVATE (European Low Emission V4 Automotive Two-stroke Engine) was a research project part funded by the European Commission to design and develop a compact and efficient gasoline two-stroke automotive engine. Five partners were involved in the project, IFP (Institut Français Du Pétrole) who were the project leaders, Lotus, Opcon (Autorotor and SEM), Politecnico di Milano and Queen's University Belfast. The general project targets were to achieve Euro 3 emissions compliance without DeNOx catalisation, and a power output of 120 kW at 5000 rev/min with maximum torque of 250 Nm at 2000 rev/min. Specific targets were a 15% reduction in fuel consumption compared to its four-stroke counterpart and a size and weight advantage over the four-stroke diesel with significant reduction in particulate and NOx emissions. This paper describes the design philosophy of the engine as well as the application of the various partner technologies used.

The purpose of the ELEVATE (European Low Emission V4 Automotive Two-stroke Engine) industrial research project is to develop a small, compact, light weight, high torque and highly efficient clean gasoline 2-stroke engine of 120 kW which could industrially replace the relatively big existing automotive spark ignition or diesel 4-stroke engine used in the top of the mid size or in the large size vehicles, including the minivan vehicles used for multi people and family transportation. This new gasoline direct injection engine concept is based on the combined implementation on a 4-stroke bottom end of several 2-stroke engine innovative technologies such as the IAPAC compressed air assisted direct fuel injection, the CAI (Controlled Auto-Ignition) combustion process, the D2SC (Dual Delivery Screw SuperCharger) for both low pressure engine scavenging and higher pressure IAPAC air assisted DI and the ETV (Exhaust charge Trapping Valve).