Search Results

Significant improvement in fuel consumption, torque delivery and emission could be achieved through flexible control of the valve timings, duration and lift. In most existing electro-hydraulic variable valve actuation systems, the desired valve lift within every engine cycle is achieved by accurately controlling of the solenoid-valve opening interval; however, due to slow response time, precision control of these valves is difficult particularly during higher engine speeds. In this paper a new lift control strategy is proposed based on the hydraulic supply pressure and flow control. In this method, in order to control the peak valve lift, the hydraulic pump speed is precisely controlled using a two-input gearbox mechanism. This eliminates the need for precision control of the solenoid valves opening interval within every cycle.

In this work, a new air hybrid engine configuration is introduced in which cam-based valvetrain along with three-way and unidirectional valves make the implementation of different air hybrid engine operational modes possible. This configuration simplifies the air hybrid engine valvetrain significantly and relaxes the necessity of using fully flexible valvetrain in air hybrid engines. Utilizing the proposed configuration allows compression braking (CB), air motor (AM), startup and conventional modes of operation to be realized. The proposed configuration is modeled in GT-Power and the deceleration of a typical vehicle, utilizing only regenerative braking system, is simulated. The efficiency of the system in storing the vehicle's kinetic energy is determined using second law definition for efficiency. The stored energy can be used to either start up the engine or run the off-engine accessories. These two modes are studied and compared.

This study proposes a novel semi-active hydro-pneumatic suspension design and investigates its performance potentials. The proposed new semi-active suspension design involves pneumatic interconnection between the front and rear suspension struts of the vehicle. The analytical formulations of suspension forces due to two suspension configurations, a passive unconnected and the proposed semi-active interconnected, are derived to analyze suspension properties. Based on a validated pitch-plane vehicle braking model, vehicle dynamic responses are conducted under a range of measured road roughness excitations and driving speeds, as well as braking inputs.

In a conventional vehicle, the longitudinal shocks caused by the road obstacles cannot be effectively absorbed due to the fact that the longitudinal connections between the chassis and wheels are typically very stiff compared with the vertical strut where the regular spring is mounted. To overcome this limitation, a concept design of a planar suspension system (PSS) is proposed. The rather stiff longitudinal linkages are replaced by a spring-damping strut in a PSS so that the vibration along any direction in the wheel plane can be effectively isolated. For a vehicle with such suspension systems, the wheels can move forth and back with respect to the chassis. The wheelbase and load distribution at the front and rear wheels can change as a consequence of the implementation of the PSS on a vehicle. The planar system can induce changes in the vehicle dynamic behavior. This paper presents the overview introduction of a dynamic study of a vehicle with such suspension systems.

This study investigates the fundamental stiffness and damping properties of a self-damped pneumatic suspension system, based on both the experimental and analytical analyses. The pneumatic suspension system consists of a pneumatic cylinder and an accumulator that are connected by an orifice, where damping is realized by the gas flow resistance through the orifice. The nonlinear suspension system model is derived and also linearized for facilitating the properties characterization. An experimental setup is also developed for validating both the formulated nonlinear and linearized models. The comparisons between the measured data and simulation results demonstrate the validity of the models under the operating conditions considered. Two suspension property measures, namely equivalent stiffness coefficient and loss factor, are further formulated.

In this work, a new air hybrid engine is introduced in which two throttles are used to manage the engine load in three modes of operation i.e. braking, air motor, and conventional mode. The concept includes an air tank to store pressurized air during braking and rather than a fully variable valve timing (VVT) system, two throttles are utilized. Use of throttles can significantly reduce the complexity of air hybrid engines. The valves need three fixed timing schedules for the three modes of operation. To study this concept, for each mode, the results of engine simulations using GT-Power software are used to generate the operating maps. These maps show the maximum braking torque as well as maximum air motor torque in terms of air tank pressure and engine speed. Moreover, the resulting maps indicate the operating conditions under which each mode is more effective. Based on these maps, a power management strategy is developed to achieve improved fuel economy.

Ride performance characteristics of a road vehicle involving different suspension system layouts are investigated. The suspension layouts consist of conventional rectangular 4-wheel, novel diamond-shaped 4-wheel, triangular 3-wheel and inverse-triangular 3-wheel. A generalized full-vehicle model integrating different suspension system layouts is formulated. The fundamental suspension properties are compared in terms of bounce-, roll- and pitch-mode. The ride dynamic responses and power consumption characteristics are explored under two measured road roughness excitations and a range of vehicle speeds. The results demonstrate that the novel diamond-shaped suspension system layout could yield significantly enhanced vehicle ride performance in an energy-saving manner.

In this study, application of differential braking strategy to remove the oscillatory instability or snaking behavior of an articulated steer vehicle is presented. First, a linearized model of the vehicle is described that is used to represent the equations of motion in the state-space form. Then, this model is utilized for designing a sliding mode controller to adjust the differential braking on the rear axle to stabilize the vehicle during the snaking. The performance of the resulting active control system is evaluated in different driving conditions by using the linearized model. Finally, the control system is incorporated into a virtual prototype of the vehicle in ADAMS, and its operation is examined. The results from the linear model analysis and simulations in ADAMS are reasonably consistent.

This paper proposes a vehicle performance/safety method using combined active steering and differential braking to achieve yaw stability and rollover avoidance. The advantages and disadvantages of active steering and differential braking control methods are identified under a variety of input signals, such as J-turn, sinusoidal, and fishhook inputs by using the implemented linear 4 DOF model. Also, the nonlinear model of the vehicle is evaluated and verified through individual and integrated controller. Each controller gives the correction steering angle and correction moment to the simplified steering and braking actuators. The integrated active steering and differential braking control are shown to be most efficient in achieving yaw stability and rollover avoidance, while active steering and differential braking control has been shown to improve the vehicle performance and safety only in yaw stability and rollover avoidance, respectively.

The on-road lateral stability of an articulated steer vehicle is investigated for both small and high deviations. First, for small deviations, a linear model of the vehicle is devised and analyzed. This planar model is generated based on some simplifying assumptions. For instance, the equations describing the tire forces and moments are linearized, and the tire rolling resistance is neglected. A linear stability analysis of the straight line motion of the vehicle with constant forward speed is conducted by using this simplified model for different values of the torsional stiffness and damping at the articulation joint. To investigate the lateral stability of the vehicle at higher deviations, the motion of a virtual prototype of the vehicle in ADAMS/View is simulated for different conditions. Finally, the results from the simulations and the linear stability analyses are compared.

To remove the snaking mode of an articulated steer vehicle, an active steering system is proposed. First, the existing steering systems of articulated steer vehicles, including hydraulic-mechanical and hydrostatic steering systems, are reviewed. Then, a combined linearized model of the vehicle with a hydraulic-mechanical steering system is developed. By using this model, two passive methods to decrease the snaking, including an increase in the friction at the articulation joint and leakage across the cylinders are detailed. To overcome the shortcomings of these solutions, an active steering system is also introduced. It is shown that the proposed steering system not only removes the instability, but also improves the steering response of the vehicle.

This paper deals with an identification method for engine rigid body inertia properties based on available accelerometer data at mount locations. Unlike other rigid body direct physical parameter identification methods, here inertia properties are extracted from an assembled engine under operating conditions. In addition to acceleration responses, only mount dynamic stiffness measurements are required and there is no need to measure unbalance forces and moments of engine. Using a linear frequency-domain model of engine, mounts, and chassis, a general algorithm is developed.

Many design problems are discovered often late in the development process, when design flexibility is limited. It is the art of the refinement engineers to find a solution to any unpredicted issues at this stage. The refinement process contains many hours of testing and requires many prototypes. Having an accurate experimental model of the system in this phase could reduce refinement time significantly. One of the areas that usually require refinement and tuning late in the design process is engine and body mounting systems. In this paper, we introduce a technique to optimize the mounting system of a vehicle for a given objective function using experimental/numerical analysis. To obtain an accurate model of the vehicle, we introduce an experimental procedure based upon the substructuring method. The method eliminates the need for any accurate finite element method of the vehicle. Experimental results of the implementation of this approach to a real vehicle are presented.

Widespread use of adaptive mounts depends on their cost, simplicity, and reliability. In this paper, a new adaptive hydraulic mount is introduced that its upper chamber compliance is changed using shape memory alloy (SMA) wires. Sensitivity analysis is used to show the effectiveness of changing the compliance on the dynamic stiffness of the mount. The finite element technique is applied to the main rubber of the hydraulic mount in which the SMA wires are embedded to calculate the maximum change in the compliance. It is shown that SMA wires can effectively modify the compliance of the upper chamber. It is also shown that a simple on-off control is sufficient for the adaptive mount.