Search Results

The work presented here seeks to compare different means of providing scavenging systems for an automotive 2-stroke engine. It follows on from previous work solely investigating uniflow scavenging systems, and aims to provide context for the results discovered there as well as to assess the benefits of a new scavenging system: the reverse-uniflow sleeve-valve. For the study the general performance of the engine was taken to be suitable to power a medium-duty truck, and all of the concepts discussed here were compared in terms of indicated fuel consumption for the same cylinder swept volume using a one-dimensional engine simulation package. In order to investigate the sleeve-valve designs layout drawings and analysis of the Rolls-Royce Crecy-type sleeve had to be undertaken.

The regulatory requirements to reduce both greenhouse gases and exhaust gas pollutants from heavy duty engines are driving new perspectives on the interaction between fuels and engines. Fuels that reliefs the burden on engine manufacturers to reach these goals are of particular interest. A low carbon fuel with a higher volatility and heating value than diesel is one such fuel that reduces engine-out emissions and carbon footprint from the entire hydrocarbon lifecycle (well-to-wheel) and improves fuel efficiency, which is a main enabler for gasoline compression ignition (GCI) technology. The present study investigated the potential of GCI technology by evaluating the performance of a low carbon high efficiency, high reactivity gasoline fuel in Doosan’s 6L medium duty diesel engine.

As SI engines strive for higher efficiency they are more likely to encounter knock and fuel anti-knock quality, which is currently measured by RON and MON, becomes more important. However, the RON and MON scales are based on primary reference fuels (PRF) - mixtures of iso-octane and n-heptane - whose autoignition chemistry is significantly different from that of practical fuels. Hence RON or MON alone can truly characterize a gasoline for its knock behavior only at their respective test conditions. The same gasoline will match different PRF fuels at different operating conditions. The true anti-knock quality of a fuel is given by the octane index, OI = RON −KS where S = RON − MON, is the sensitivity. K depends on the pressure and temperature evolution in the unburned gas during the engine cycle and hence is different at different operating conditions and is negative in modern engines.

In a regulatory environment for spark ignition (SI) engines where the focus is continuously looking into improvements in fuel economy and reduction in noxious emissions, the challenges to achieve future requirements are utmost. To effectively reduce CO2 emissions on a well-to-wheel basis, future fuels enabling high efficiency SI engines will have to not only satisfy advanced engine requirements, i.e. high knock resistance, but also produce less CO2 emissions in the refinery. This paper describes how to characterize SI combustion's on-demand octane requirement with three different dual fuel configurations. Refinery naphtha was used for low octane component, and three oxygenates were used for high octane knock inhibiting component, such as, Methanol and Methyl tert-butyl ether (MTBE) and Ethyl tert-butyl ether (ETBE). Each low and high octane fuel was introduced via production gasoline direct injector (DI) and port fuel injector (PFI) in both configurations.

Low temperature combustion concepts are studied recently to simultaneously reduce NOX and soot emissions. Optical studies are performed to study gasoline PPC in CI engines to investigate in-cylinder combustion and stratification. It is imperative to perform emission measurements and interpret the results with combustion images. In this work, we attempt to investigate this during the transition from CI to HCCI mode for FACE I gasoline (RON = 70) and its surrogate, PRF70. The experiments are performed in a single cylinder optical engine that runs at a speed of 1200 rpm. Considering the safety of engine, testing was done at lower IMEP (3 bar) and combustion is visualized using a high-speed camera through a window in the bottom of the bowl. From the engine experiments, it is clear that intake air temperature requirement is different at various combustion modes to maintain the same combustion phasing.

Partially premixed combustion (PPC) is a low-temperature combustion concept, which is between conventional diesel compression ignition (CI) and homogeneous charge compression ignition (HCCI). In PPC mode, the start of injection timing (SOI) is earlier than that of CI and later than that of HCCI and stratified in-cylinder fuel/air mixture can be formed to control the auto-ignition by the fuel injection timing. Gasoline fuel is beneficial for PPC mode because of its superior resistance to auto-ignition, which can enhance fuel-air charge mixing process with longer ignition delay time. The scope of this study is to investigate in-cylinder auto-ignition, combustion evolution, combustion stratification, and engine-out emissions at PPC operating mode under lean and low load engine conditions with different injection timings. Primary reference fuel PRF77, was selected as the low-octane test fuel.

In this study, the combustion system of a light-duty compression ignition engine running on a market gasoline fuel with Research Octane Number (RON) of 91 was optimized using computational fluid dynamics (CFD) and Machine Learning (ML). This work was focused on optimizing the piston bowl geometry at two compression ratios (CR) (17 and 18:1) and this exercise was carried out at full-load conditions (20 bar indicated mean effective pressure, IMEP). First, a limited manual piston design optimization was performed for CR 17:1, where a couple of pistons were designed and tested. Thereafter, a CFD design of experiments (DoE) optimization was performed where CAESES, a commercial software tool, was used to automatically perturb key bowl design parameters and CONVERGE software was utilized to perform the CFD simulations. At each compression ratio, 128 piston bowl designs were evaluated.

Light naphtha is the light distillate from crude oil and can be used in compression ignition (CI) engines; its low boiling point and octane rating (RON = 64.5) enable adequate premixing. This study investigates the combustion characteristics of light naphtha (LN) and its multicomponent surrogate under various start of injection (SOI) conditions. LN and a five-component surrogate for LN, comprised of 43% n-pentane, 12% n-heptane, 10% 2-methylhexane, 25% iso-pentane and 10% cyclo-pentane, has been tested in a single cylinder optical diesel engine. The transition in combustion homogeneity from CI combustion to homogenized charge compression ignition (HCCI) combustion was then compared between LN and its surrogate. The engine experimental results showed good agreement in combustion phasing, ignition delay, start of combustion, in-cylinder pressure and rate of heat release between LN and its surrogate.

Partially premixed combustion (PPC) is an operating mode that lies between the conventional compression ignition (CI) mode and homogeneous charge compression ignition (HCCI) mode. The combustion in this mixed mode is complex as it is neither diffusion-controlled (CI mode) nor governed solely by chemical kinetics (HCCI mode). In this study, CFD simulations were performed to evaluate flame index, which distinguishes between zones having a premixed flame and non-premixed flame. Experiments performed in the optical engine supplied data to validate the model. In order to realize PPC, the start of injection (SOI) was fixed at −40 CAD (aTDC) so that a required ignition delay is created to premix air/fuel mixture. The reference operating point was selected to be with 3 bar IMEP and 1200 rpm. Naphtha with a RON of 77 and its corresponding PRF surrogate were tested. The simulations captured the general trends observed in the experiments well.

In the context of stringent future emission standards as well as the need to reduce emissions of CO2 on a global scale, the cost of manufacturing engines is increasing. Naphtha has been shown to have beneficial properties for its use as a fuel in the transportation sector. Well to tank CO2 emissions from the production of Naphtha are lower than any other fuel produced in the refinery due to its lower processing requisites. Moreover, under current technology trends the demand for diesel is expected to increase leading to a possible surplus of light fuels in the future. Recent research has demonstrated that significant fuel consumption reduction is possible based on a direct injection gasoline engine system, when a low quality gasoline stream such as Naphtha is used in compression ignition mode. With this fuel, the engine will be at least as efficient and clean as current diesel engines but will be more cost effective (lower injection pressure, HC/CO after-treatment rather than NOx).

The present investigation pertains to the development of fast idle catalyst light-off strategy for a light duty gasoline compression ignition (GCI) engine. The engine cold start fast idle operation poses a problem of increased criteria emissions if the catalyst is not activated during the warm up period. Therefore, a control strategy is proposed here to minimize the criteria pollutants during the fast idle phase via enabling fast catalyst light off in a GCI engine and relying on the spark ignition of a globally stoichiometric fuel air mixture. The engine has unique design features such as certain geometry configuration between spark plug and fuel injector arrangement, and the location of spark plug in a high compression ratio (CR) diesel-like combustion chamber. The experiments were performed in a single cylinder GCI engine at cold start fast idle conditions using certification gasoline fuel (RON 91).

The present investigation expands on our previous work on development of fast idle catalyst light-off strategy for a light duty gasoline compression ignition (GCI) engine. In part 1, the steady state experimental investigation in a single cylinder GCI engine indicate an optimum strategy for effective catalyst light off during cold start fast idle operation. According to this strategy, the strategy includes (1) dispersing a first fuel injection during the intake stroke, (2) dispersing a second fuel injection during the expansion stroke, and (3) igniting a spark during the expansion stroke. This strategy increases the exhaust temperature during cold starts thereby assisting in lighting the oxidation catalyst, and reduce emissions and provide greater combustion stability as compared to other injection and spark strategies.

The objective of this study was to investigate the effect of aromatic on combustion stratification and particulate emissions for PRF60. Experiments were performed in an optical CI engine at a speed of 1200 rpm for TPRF0 (100% v/v PRF60), TPRF20 (20% v/v toluene + 80% PRF60) and TPRF40 (40% v/v toluene + 60% PRF60). TPRF mixtures were prepared in such a way that the RON of all test blends was same (RON = 60). Single injection strategy with a fuel injection pressure of 800 bar was adopted for all test fuels. Start of injection (SOI) was changed from early to late fuel injection timings, representing various modes of combustion viz HCCI, PPC and CDC. High-speed video of the in-cylinder combustion process was captured and one-dimensional stratification analysis was performed from the intensity of images. Particle size, distribution and concentration were measured and linked with the in-cylinder combustion images.

Gasoline compression ignition (GCI) engines have been considered an attractive alternative to traditional spark ignition engines. Low octane gasoline fuel has been identified as a viable option for the GCI engine applications due to its longer ignition delay characteristics compared to diesel and in the volatility range of gasoline fuels. In this study, we have investigated the effect of different injection timings at part-load conditions using light naphtha stream in single cylinder engine experiments in the GCI combustion mode with injection pressure of 130 bar. A toluene primary reference fuel (TPRF) was used as a surrogate for the light naphtha in the engine simulations performed here. A physical surrogate based on the evaporation characteristics of the light naphtha has been developed and its properties have been implemented in the engine simulations.

More stringent emissions standards along with higher fuel economy demands have obliged auto makers to develop technical solutions that exploit synergistic features from gasoline and diesel engines. To minimize NOx and soot trade-off, diesel powertrain has been developed to adopt increasingly complex and expensive technology such as extremely high pressure fuel injection systems, low pressure EGR, and variable valve timing. These attempts are associated with promoting Partially Premixed Charge Compression Ignition (PPC-CI) combustion via increasing mixing time and ignition delay. Alternatively, PPC-CI combustion can be achieved easier by using fuels with higher resistance to auto-ignition than conventional diesel fuel. Previous work has demonstrated the possibility of reducing the cost of future diesel after-treatment systems by using gasoline-like fuels.

The global need for de-carbonization and stringent emission regulations are pushing the current engine research toward alternative fuels. Previous studies have shown that the uHC, CO, and CO2 emissions are greatly reduced and brake thermal efficiency increases with an increase in hydrogen concentration in methane-hydrogen blends for the richer mixture compositions. However, the combustion suffers from high NOx emissions. While these trends are well established, there is limited information on a detailed optical study on the effect of air-excess ratio for different methane-hydrogen mixtures. In the present study, experimental investigations of different methane-hydrogen blends between 0 and 100% hydrogen concentration by volume for the air-excess ratio of 1, 1.4, 1.8, and 2.2 were conducted in a heavy-duty optical diesel engine converted to spark-ignition operation. The engine was equipped with a flat-shaped optical piston to allow bottom-view imaging of the combustion chamber.

Recent research [21] has shown that the compression ignition concept where very low cetane fuels (RON between 70 and 85) are run in compression ignition (CI) mode has several advantages. The engine will be at least as efficient and clean as the current diesel engines but will have a less complicated after-treatment system. The optimum fuel will be less processed and therefore simpler to make compared to current gasoline or diesel fuels. Naphtha, which is a product of the initial distillation of petroleum, is one such fuel. It provides a path to mitigate the global demand imbalance between heavier and lighter fuels that is otherwise projected. Since naphtha requires much less processing in the refinery than either gasoline or diesel [23], there is an additional benefit in terms of well-to-wheel CO2 emissions and overall energy consumed. Partially premixed charge compression ignition combustion with such a low cetane fuel has usually been investigated with a diesel engine base.

The literature study on PPC in optical engine reveals investigations on OH chemiluminescence and combustion stratification. So far, mostly PRF fuel is studied and it is worthwhile to examine the effect of fuel properties on PPC. Therefore, in this work, fuel having different octane rating and physical properties are selected and PPC is studied in an optical engine. The fuels considered in this study are diesel, heavy naphtha, light naphtha and their corresponding surrogates such as heptane, PRF50 and PRF65 respectively. Without EGR (Intake O2 = 21%), these fuels are tested at an engine speed of 1200 rpm, fuel injection pressure of 800 bar and pressure at TDC = 35 bar. SOI is changed from late to early fuel injection timings to study PPC and the shift in combustion regime from CI to PPC is explored for all fuels. An increased understanding on the effect of fuel octane number, physical properties and chemical composition on combustion and emission formation is obtained.

Extensive tests have been carried out in a single-cylinder Direct Injection Spark Ignition (DISI) engine using up to fifteen different fuels at inlet pressure of up to 3.4 bar abs. to study fuel effects as well as inlet pressure effects on knock. In addition fuel effects on particulate emissions at part-throttle were measured. Fuel anti-knock quality does not correlate with MON and is best described by the Octane Index, OI = RON-KS where S = RON -MON is the sensitivity of the fuel and K is a constant depending on the engine pressure/temperature regime. The RON of the fuels considered was in the range between 95 and 105 and the sensitivity between 8 and 13. K is negative at all the conditions tested, i.e., for a given RON, a higher sensitivity fuel has better anti-knock quality. K decreases with increasing intake pressure and more generally, decreases as Tcomp₁₅, the temperature of the unburned gas at a pressure of 15 bar decreases.

This paper is the second of a two part study which investigates the use of advanced combustion modes as a means of improving the efficiency and environmental impact of conventional light-duty vehicles. This second study focuses on drive cycle simulations and Life Cycle Assessment (LCA) for vehicles equipped with Octane-on-Demand combustion. Methanol is utilized as the high octane fuel, while three alternative petroleum-derived fuels with Research octane numbers (RONs) ranging from 61 to 90 are examined as candidates for the lower octane fuel. The experimental engine calibration maps developed in the previous study are first provided as inputs to a drive cycle simulation tool. This is used to quantify the total fuel consumption, octane requirement and tank-to-wheel CO2 emissions for a light-duty vehicle equipped with two alternative powertrain configurations. The properties of the lower octane fuel are shown to affect the vehicle fuel consumption and CO2 emissions significantly.