Search Results

This paper presents the vehicle model development and validation process for the Ford Focus battery electric vehicles (BEVs) using Autonomie and test results from Advanced Powertrain Research Facility in Argonne National Laboratory. The parameters or characteristic values for the important components such as the electric machine and battery pack system are estimated through analyzing the test data of the multi cycle test (MCT) procedure under the standard ambient condition. A novel process was used to import vehicle test data into Autonomie. Through this process, a complete vehicle model of the Ford Focus BEV is developed and validated under ambient temperature for different drive cycles (UDDS, HWFET, US06 and Steady-State). The simulation results of the developed vehicle model show coincident results with the test data within 0.5% ∼ 4% discrepancies for electrical consumption.

Because of their high efficiency and low emissions, fuel-cell vehicles are undergoing extensive research and development. As the entire powertrain system needs to be optimized, the requirements of each component to achieve FreedomCAR goals need to be determined. With the collaboration of FreedomCAR fuel cell, energy storage, and vehicle Technical Teams, Argonne National Laboratory (ANL) used several modeling tools to define the energy storage requirements for fuel cell vehicles. For example, the Powertrain System Analysis Toolkit (PSAT), which is a transient vehicle simulation software, was used with a transient fuel cell model derived from the General Computational Toolkit (GCtool). This paper describes the impact of degree of hybridization, control strategy, and energy storage technology on energy storage requirements for a fuel cell SUV vehicle platform.

Their easy availability, lower well-to-wheel emissions, and relative ease of use with existing engine technologies have made ethanol and ethanol-gasoline blends a viable alternative to gasoline for use in spark-ignition (SI) engines. The lower energy density of ethanol and ethanol-gasoline blends, however, results in higher volumetric fuel consumption compared with gasoline. Also, the higher latent heat of vaporization can result in cold-start issues with higher-level ethanol blends. On the other hand, a higher octane number, which indicates resistance to knock and potentially enables more optimal combustion phasing, results in better engine efficiency, especially at higher loads. This paper compares the fuel consumption and emissions of two ethanol blends (E50 and E85) with those for gasoline when used in conventional (non-hybrid) and power-split-type plug-in hybrid electric vehicles (PHEVs).

Fuel cell vehicles are undergoing extensive research and development because of their potential for high efficiency and low emissions. Because fuel cell vehicles remain expensive and there is limited demand for hydrogen at present, very few fueling stations are being built. To try to accelerate the development of a hydrogen economy, some original equipment manufacturers in the automotive industry have been working on a hydrogen-fueled internal combustion engine (ICE) as an intermediate step. This paper compares the fuel economy potential of hydrogen powertrains to conventional gasoline vehicles. Several timeframes are considered: 2010, 2015, 2030, and 2045. To address the technology status uncertainty, a triangular distribution approach was implemented for each component technology. The fuel consumption and cost of five powertrain configurations will be discussed and compared with the conventional counterpart.

Many of today's vehicle modeling tools are good for simulation, but they provide rather limited support for model building and management. Setting up a simulation model requires more than writing down state equations and running them on a computer. The role of a model library is to manage the physics of the system and allow users to share and reuse component models. In this paper, we describe how modern software techniques can be used to support modeling and design activities; the objective is to provide better system models in less time by assembling these system models in a “plug and play” architecture. With the introduction of hybrid electric vehicles, the number of components that can populate a model has increased considerably, and more components translates into more drivetrain configurations. To address these needs, we explain how users can simulate a large number of drivetrain configurations.

In recent studies, optimal control has shown promise as a strategy for enhancing the energy efficiency of connected autonomous vehicles. To maximize optimization performance, it is important to accurately predict constraints, especially separation from a vehicle in front. This paper proposes a novel prediction method for forecasting the trajectory of the nearest preceding car. The proposed predictor is designed to produce short to medium-length speed trajectories using a locally weighted polynomial regression algorithm. The polynomial coefficients are trained by using two types of information: (1) vehicle-to-vehicle (V2V) messages transmitted by multiple preceding vehicles and (2) vehicle-to-infrastructure (V2I) information broadcast by roadside equipment. The predictor’s performance was tested in a multi-vehicle traffic simulation platform, RoadRunner, previously developed by Argonne National Laboratory.

Plug-in Hybrid Electric Vehicles (PHEVs) have demonstrated the potential to provide significant reduction in fuel use across a wide range of dynamometer test driving cycles. Companies and research organizations are involved in numerous research activities related to PHEVs. One of the current unknowns is the impact of driving behavior and standard test procedure on the true benefits of PHEVs from a worldwide perspective. To address this issue, five different PHEV powertrain configurations (input split, parallel, series, series-output split and series-parallel), implemented on vehicles with different all-electric ranges (AERs), were analyzed on three different standard cycles (i.e., Urban Dynamometer Driving Schedule, Highway Fuel Economy Test, and New European Driving Cycle). Component sizes, manufacturing cost, and fuel consumption were analyzed for a midsize car in model year 2020 through the use of vehicle system simulations.

This study presents a process to quantify the fuel saving potential of electrified powertrains for medium and heavy duty vehicles. For this study, equivalent vehicles with electrified powertrains are designed with the underlying principle of not compromising on cargo carrying capacity or performance. Several performance characteristics, that are relevant for all types of medium and heavy duty vehicles, were identified for benchmarking based on the feedback from the industry. Start-stop hybrids, parallel pre-transmission hybrids, plug-in hybrids, and battery electric vehicles are the technology choices in this study. This paper uses one vehicle as an example, explains the component sizing process followed for each powertrain, and examines each powertrain’s fuel saving potential. The process put forth in this paper can be used for evaluating vehicles that belong to all medium and heavy duty classes.

This paper introduces an eco-driving highway cruising algorithm based on optimal control theory that is applied to a conventionally-powered connected and automated vehicle. Thanks to connectivity to the cloud and/or to infrastructure, speed limit and slope along the future route can be known with accuracy. This can in turn be used to compute the control variable trajectory that will minimize energy consumption without significantly impacting travel time. Automated driving is necessary to the implementation of this concept, because the chosen control variables (e.g., torque and gear) impact vehicle speed. An optimal control problem is built up where quadratic models are used for the powertrain. The optimization is solved by applying Pontryagin’s minimum principle, which reduces the problem to the minimization of a cost function with parameters called co-states.

Argonne National Laboratory (ANL), working with the Partnership for a New Generation of Vehicles (PNGV), maintains hybrid vehicle simulation software: the PNGV System Analysis Toolkit (PSAT). The importance of component models and the complexity involved in setting up optimized control strategies require validation of the models and controls developed in PSAT. Using ANL's Advanced Powertrain Test Facilities (APTF), more than 50 tests on the Honda Insight were used to validate the PSAT drivetrain configuration. Extensive instrumentation, including the half-shaft torque sensor, provides the data needed for through comparison of model results and test data. In this paper, we will first describe the process and the type of test used to validate the models. Then we will explain the tuning of the simulated vehicle control strategy, based on the analysis of the differences between test and simulation.

The establishment of Corporate Average Fuel Economy (CAFE) standards by the Energy Policy and Conservation Act (EPCA) of 1975 marked a pivotal moment in the automotive industry's pursuit of greater fuel efficiency. The responsibility for the development and enforcement of these standards was assigned to the U.S. Department of Transportation (DOT), with the National Highway Traffic Safety Administration (NHTSA) assuming a critical role in their oversight and implementation. In collaboration with Argonne National Laboratory (Argonne), supported by the U.S. Department of Energy (DOE), significant strides have been made in advancing fuel efficiency through the development of Autonomie, a leading full-vehicle simulation tool. Through an Inter-Agency Agreement between the DOE Argonne Site Office and Argonne, comprehensive full-vehicle simulations are conducted to support NHTSA's CAFE rulemaking processes.

Near-term advances in spark ignition (SI) engine technology (e.g., variable value lift [VVL], gasoline direct injection [GDI], cylinder deactivation, turbo downsizing) for passenger vehicles hold promise of delivering significant fuel savings for vehicles of the immediate future. Similarly, trends in transmissions indicate higher (8-speed, 9-speed) gear numbers, higher spans, and a focus on downspeeding to improve engine efficiency. Dual-clutch transmissions, which exhibit higher efficiency in lower gears, than the traditional automatics, and are being introduced in the light-duty vehicle segment worldwide. Another development requiring low investment and delivering immediate benefits has been the adaptation of start-stop (micro hybrids or idle engine stop technology) technology in vehicles today.

Connectivity and automation are increasingly being developed for cars and trucks, aiming to provide better safety and better driving experience. As these technologies mature and reach higher adoption rates, they will also have an impact on the energy consumption: Connected and Automated Vehicles (CAVs) may drive more smoothly, stop less often, and move at faster speeds, thanks to overall improvements to traffic flows. These potential impacts are not well studied, and any existing studies tend to focus solely on conventional engine-powered cars, leaving aside electrified vehicles such as Hybrid Electric Vehicles (HEVs) and Battery Electric Vehicles (BEVs). This work intends to address this issue by analyzing the energy impact of various CAV scenarios on different types of electric vehicles using high-fidelity models. The vehicles-all midsize, one HEV, one BEV, and a conventional-are modeled in Autonomie, a high-fidelity, forward-looking vehicle simulation tool.

Plug-in Hybrid Electric Vehicles (PHEVs) offer the ability to significantly reduce petroleum consumptions. Argonne National Laboratory (ANL), working with the FreedomCAR and Fuels Partnership, participated in the definition of the battery requirements for PHEVs. Previous studies have demonstrated the impact of vehicle characteristics such as vehicle class, mass or electrical accessories. However, outstanding questions remain regarding the impact of drive cycles on the requirements. In this paper, we will first evaluate the consequences of sizing the electrical machine and the battery powers to follow the Urban Dynamometer Driving Schedule (UDDS) to satisfy CARB requirements, including how many other driving cycles can be followed in Electric Vehicle (EV) mode. Then, we will study the impact of sizing the electrical components on other driving cycles.

Manufacturers have been considering various technology options to improve vehicle fuel economy. Some of the most promising technologies are related to vehicle electrification. To evaluate the benefits of vehicle electrification to support the 2017-2025 CAFE regulations, a study was conducted to simulate many of the most common electric drive powertrains currently available on the market: 12V Micro Hybrid Vehicle (start/stop systems), Belt-integrated starter generator (BISG), Crank-integrated starter generator (CISG), Full Hybrid Electric Vehicle (HEV), PHEV with 20-mile all-electric range (AER) (PHEV20), PHEV with 40-mile AER (PHEV40), Fuel-cell HEV and Battery Electric vehicle with 100-mile AER (EV100). Different vehicle classes were also analyzed in the study process: Compact, Midsize, Small SUV, Midsize SUV and Pickup. This paper will show the fuel displacement benefit of each powertrain across vehicle classes.

Because of their high efficiency and low emissions, fuel-cell vehicles are undergoing extensive research and development. When considering the introduction of advanced vehicles, engineers must perform a well-to-wheel (WTW) evaluation to determine the potential impact of a technology on carbon dioxide and Greenhouse Gas (GHG) emissions and to establish a basis that can be used to compare other propulsion technology and fuel choices. Several modeling tools developed by Argonne National Laboratory (ANL) were used to evaluate the overall environmental and fuel-saving impacts associated with an advanced powertrain configuration. The Powertrain System Analysis Toolkit (PSAT) transient vehicle simulation software was used for pump-to-wheel (PTW) analysis, and GREET (Greenhouse gases, Regulated Emissions and Energy use in Transportation) was used for well-to-pump (WTP) analysis. This paper assesses the impact of FreedomCAR vehicle goals on a WTW energy basis.

Plug-in hybrid electric vehicles (PHEVs) have the ability to significantly reduce petroleum consumption. Argonne National Laboratory (Argonne), working with the FreedomCAR and Fuels Partnership, helped define the battery requirements for PHEVs. Previous studies demonstrated the impact of the vehicle's characteristics, such as its class, mass, or electrical accessories, on the requirements. However, questions on the impact of drive cycles remain outstanding. In this paper, we evaluate the consequences of sizing the electrical machine and the battery to follow standard drive cycles, such as the urban dynamometer driving schedule (UDDS), as well as real-world drive cycles in electric vehicle (EV) mode. The requirements are defined for several driving conditions (e.g., urban, highway) and types of driving behavior (e.g., smooth, aggressive).

Thermoelectric generators (TEGs) can be used for a variety of applications in automobiles. There is a lot of interest in using them for waste heat recovery from a fuel economy point of view. This paper examines the potential of TEGs to provide cost-effective improvements in the fuel economy of conventional vehicles and hybrid electric vehicles (HEVs). Simulation analysis is used to quantify fuel economy benefits. The paper explains how a TEG is used in a vehicle and explores the idea of improving the TEG design by introducing a thermal reservoir in the TEG model to improve the waste heat recovery. An effort is made to identify the technological and economic barriers (and their thresholds) that could prevent TEGs from becoming an acceptable means of waste heat recovery in automobiles.

In support of the U.S Department of Energy's Vehicle Technologies Program, numerous vehicle technology combinations have been simulated using Autonomie. Argonne National Laboratory (Argonne) designed and wrote the Autonomie modeling software to serve as a single tool that could be used to meet the requirements of automotive engineering throughout the development process, from modeling to control, offering the ability to quickly compare the performance and fuel efficiency of numerous powertrain configurations. For this study, a multitude of vehicle technology combinations were simulated for many different vehicles classes and configurations, which included conventional, power split hybrid electric vehicle (HEV), power split plug-in hybrid electric vehicle (PHEV), extended-range EV (E-REV)-capability PHEV, series fuel cell, and battery electric vehicle.

Manufacturers have been considering various technology options to improve vehicle fuel economy. One of the most cost effective technology is related to advanced transmissions. To evaluate the benefits of transmission technologies and control to support the 2017-2025 CAFE regulations, a study was conducted to simulate many of the many types of transmissions: Automatic transmissions, Manual Transmission as well as Dual Clutch Transmissions including the most commonly used number of gears in each of the technologies (5-speeds, 6-speeds, and 8-speeds). Different vehicle classes were also analyzed in the study process: Compact, Midsize, Small SUV, Midsize SUV and Pickup. This paper will show the fuel displacement benefit of each advanced transmission across vehicle classes.