Search Results

In recent years, the increase of gasoline fuel injection pressure is a way to improve thermal efficiency and lower engine-out emissions in GDI homogenous combustion concept. The challenge of controlling particulate formation as well in mass and number concentrations imposed by emissions regulations can be pursued improving the mixture preparation process and avoiding mixture inhomogeneity with ultra-high injection pressure values up to 100 MPa. The increase of the fuel injection pressure in GDI homogeneous systems meets the demand for increased injector static flow, while simultaneously improves the spray atomization and mixing characteristics with consequent better combustion performance. Few studies quantify the effects of high injection pressure on transient gasoline spray evolution. The aim of this work was to simulate with OpenFOAM the spray morphology of a commercial gasoline injected in a constant volume vessel by a prototypal GDI injector.

The increasing diffusion of gasoline direct injection (GDI) engines requires a more detailed and reliable description of the phenomena occurring during the fuel injection process. As well known the thermal and fluid-dynamic conditions present in the combustion chamber greatly influence the air-fuel mixture process deriving from GDI injectors. GDI fuel sprays typically evolve in wide range of ambient pressure and temperatures depending on the engine load. In some particular injection conditions, when in-cylinder pressure is relatively low, flash evaporation might occur significantly affecting the fuel-air mixing process. In some other particular injection conditions spray impingement on the piston wall might occur, causing high unburned hydrocarbons and soot emissions, so currently representing one of the main drawbacks of GDI engines.

In the present paper, a new concept of open nozzle spray was investigated as possible application for compression ignition engines. The study concerns an experimental and numerical characterization of a spray generated through a prototype high-pressure hollow-cone nozzle (HCN). The experimental description of the injection process was carried out under evaporative and non-evaporative conditions injecting the fuel in a constant-volume combustion vessel controlled in pressure and temperature in order to measure the spatial and temporal fuel pattern at engine-like gas densities. OpenFOAM libraries in the lib-ICE version of the numerical code were employed for simulating the spray dynamics after a first validation phase based on the experimental data. Results show a typical spray structure of the outward-opening nozzle with the overall fluid-dynamic arrangement having a good fuel distribution along the hollow-cone geometry but showing a reduced spatial penetration.

The adoption of gaseous fuels for Light Duty (LD) engines is considered a promising solution to efficiently reduce greenhouse gases emissions and diversify fuels supplies, while keeping pollutants production within the limits. In this respect, the Dual Fuel (DF) concept has already proven to be, generally speaking, a viable solution, industrially implemented for several applications in the Heavy-Duty (HD) engines category. Despite this, some issues still require a technological solution, preventing the commercialization of DF engines in wider automotive fields, including the release of high amounts of unburned species, possibility of engine knock, chance of thermal efficiency reduction. In this framework, numerical simulation can be a useful tool, not only to better understand specific characteristics of DF combustion, but also to explore specific geometrical modifications and engine calibrations capable to adapt current LD architectures to this concept.

In the aim of reducing CO2 emissions and fuel consumption, the improvement of the diesel engine performance is based on the optimization of the whole combustion system efficiency. The focus of new technological solutions is devoted to the optimization of thermodynamic efficiency especially in terms of reduction of losses of heat exchange. In this context, it is required a continuous development of the engine combustion system, first of all the injection system and in particular the nozzle design. To this reason in the present paper a new concept of an open nozzle spray was investigated as a possible solution for application on diesel engines. The study concerns some experimental and numerical activities on a prototype of an open nozzle. An external supplier provided the prototypal version of the injector, with a dedicated piezoelectric actuation system, and with an appropriate choice of geometrical design parameters.

The paper reports an experimental study on the effect of compression ratio variation on the performance and pollutant emissions of a single-cylinder light-duty research diesel engine operating in DF mode. The architecture of the combustion system as well as the injection system represents the state-of-the-art of the automotive diesel technology. Two pistons with different bowl volume were selected for the experimental campaign, corresponding to two CR values: 16.5 and 14.5. The designs of the piston bowls were carefully performed with the 3D simulation in order to maintain the same air flow structure at the piston top dead center, thus keeping the same in-cylinder flow characteristics versus CR. The engine tests choice was performed to be representative of actual working conditions of an automotive light-duty diesel engine.

An increasing interest in the use of natural gas in CI engines is currently taking place, due to several reasons: it is cheaper than conventional Diesel fuel, permits a significant reduction in the amount of emitted carbon dioxide and is intrinsically cleaner, being much less prone to soot formation. In this respect, the Dual Fuel (DF) concept has already proven to be a viable solution, industrially implemented for several applications in the high duty engines category. Despite this, some issues still require a technological solution, preventing the commercialization of DF engines in wider automotive fields: the release of high amounts of unburned fuel, the risk of engine knock, the possible thermal efficiency reduction are some factors regarding the fuel combustion aspect. DF configuration examined in the present paper corresponds to Port Fuel Injection of natural gas and direct injection of the Diesel Fuel.

This paper reports an experimental and numerical investigation on the spatial and temporal liquid- and vapor-phase distributions of diesel fuel spray under engine-like conditions. The high pressure diesel spray was investigated in an optically-accessible constant volume combustion vessel for studying the influence of the k-factor (0 and 1.5) of a single-hole axial-disposed injector (0.100 mm diameter and 10 L/d ratio). Measurements were carried out by a high-speed imaging system capable of acquiring Mie-scattering and schlieren in a nearly simultaneous fashion mode using a high-speed camera and a pulsed-wave LED system. The time resolved pair of schlieren and Mie-scattering images identifies the instantaneous position of both the vapor and liquid phases of the fuel spray, respectively. The studies were performed at three injection pressures (70, 120, and 180 MPa), 23.9 kg/m3 ambient gas density, and 900 K gas temperature in the vessel.

The present paper describes an experimental and numerical study on the effect of the nozzle flow number (FN) on the full load performance of a modern Euro5 diesel automotive engine, in terms of torque, efficiency and exhaust emissions. The improvement of the diesel engine performance requires a continuous development of the engine components, first of all the injection system and in particular the nozzle design. One of the most crucial factors affecting performance and emissions is the nozzle flow number and its influence becomes more and more important as high performance and low emissions are continuous requirements. Indeed, reducing the nozzle flow number, due to an increase of spray-air mixing, an improvement in PM-NOx trade-off is generally expectable. On the other hand, at full load, where peak firing pressure and exhaust valve temperature become the limiting factors, critical operating conditions can be easily reached reducing the nozzle hole diameter.

Premixed combustion modes in compression ignition engines are studied as a promising solution to meet fuel economy and increasingly stringent emissions regulations. Nevertheless, PCCI combustion systems are not yet consolidated enough for practical applications. The high complexity of such combustion systems in terms of both air-fuel charge preparation and combustion process control requires the employment of robust and reliable numerical tools to provide adequate comprehension of the phenomena. Object of this work is the development and validation of suitable models to evaluate the effects of charge premixing levels in diesel combustion. This activity was performed using the Lib-ICE code, which is a set of applications and libraries for IC engine simulations developed using the OpenFOAM® technology.

The OpenFOAM® CFD methodology is nowadays employed for simulation in internal combustion engines and a lot of work has been done for an appropriate description of all complex phenomena. At the moment in the RANS turbulence models available in the OpenFOAM® toolbox the turbulence modulation is not yet included, and the present work analyzes the predictive capabilities of the code in simulating high injection pressure fuel sprays after modeling the influence of the dispersed phase on the turbulence structure. Different experiments were employed for the validation. At first, non-evaporating diesel spray was considered in a constant volume and quiescent vessel. The validation was performed via the available experimental spray evolution in terms of penetrations and spatial/temporal fuel distributions. Then the Sandia combustion chamber was chosen for diesel spray simulation in non-reacting conditions.

The present work is focused on multidimensional simulations of combustion in Diesel engines, using detailed kinetics reaction schemes. The selected reaction mechanism is the scheme developed by Liu et al. [1].The simulations are performed through the open source CFD Toolbox OpenFOAM (Open Field Operation and Manipulation). OpenFoam uses finite volume methods to solve systems of partial differential equations ascribed on any 3D unstructured mesh of polyhedral cells. A preliminary analysis relevant for diesel combustion studies is performed in constant volume homogeneous conditions. Here the treatment of the stiff ordinary differential equations arising from the usage of detailed kinetics reaction mechanisms and the performance of different solvers are investigated. The CVODE package has been integrated in OpenFOAM, as an alternative solver to the one provided by the original version of the code.

This paper describes a characterisation of the combustion behaviour in an optical Common Rail diesel engine fed by different advanced fuels, via the application of the two-colour pyrometry technique. The acquired images were processed in order to calculate the instantaneous flame temperature and soot volume fraction. For the measurements, a single test point was chosen as representative of the reference four-cylinder engine performance in the European driven cycle ECE+EUDC. The test point was the 1500 rpm and 22 mm3/stroke of injected fuel volume, correspondent to the engine point of 1500rpm @ 5 bar of BMEP for the 4-cylinder engine of 1.9L of displacement. As general overview, the flame luminosity from combustion of the fuel injected during pilot injection was always below the threshold of sensitivity of the detection system.

This paper reports some results on the performance of an advanced common rail (CR) DI diesel engine burning 12 model diesel fuels. The experiments were carried out within a co-operative research program “NeDeNeF” (New Diesel Engines and New Diesel Fuels), partly sponsored by the Commission of European Communities. Partners of the project with Istituto Motori (IM) were: FEV (Germany), VTT (Finland), NTUA (Greece), Brunel University (UK), Fortum (Finland), LAT (Greece) under the coordination of the IFP (France). The matrix of twelve fuels was prepared by the fuel producer partner (Fortum). The research program of the Diesel Engines and Fuels Department of Istituto Motori aimed at assessing the effect of fuel quality on exhaust emissions. The engine employed in the tests was a Fiat four-cylinder DI CR diesel engine, EURO3 version, of 1.9 litre, installed on Fiat Group class C Cars (1350kg of mass).

This paper describes a preliminary characterization of in-cylinder spray and combustion behavior from a high-pressure common rail injection system. The engine used in the tests was a single-cylinder optical research diesel engine, adequately developed in a full-fired version, equipped with a common rail injection system. An elongated piston allows for the optical access to the combustion chamber for diagnostic applications. Characteristic of the optical engine is the availability to investigate different combustion system designs due to an interchangeable head-cylinder group. The system configuration tested in the present work corresponds to a four-cylinder engine of 1930 cc of displacement that is representative in the class of light duty d.i. diesel engine. Spray and combustion evolutions were visualized through a high-speed CCD camera synchronized with a copper vapor laser acting as light source.

In this paper some preliminary results on the emission performance of a modern CR DI diesel engine running on reformulated diesel fuels are discussed. The engine employed in the tests was a Fiat M724 1910cc, installed on Alfa Romeo 156 1.9 JTD. Modern injection systems can modify the spray structure with respect to a spray of a classical rotary injection pump so the well-consolidated knowledge on the correlation between fuel parameters and pollutant emissions may not be valid for the new generation of DI diesel engines. Two high quality fossil fuels and a synthetic fuel were selected for the tests. Tests were directed to analyze the relative influence on exhaust emissions between injection parameters and fuel quality. One engine test point (2000 rpm × 2 bar of b.m.e.p.) was chosen, with different setting of injection pressure, EGR ratio and pilot injection activation.