Search Results

The current publication considers the benefits of placing a SCR system upstream of the DOC. This will enable rapid light-off of the upstream system. The tradeoff between engine out NOx levels, exhaust temperature, and dosing levels between upstream and downstream SCR will be compared with respect to achieving below 0.05 g/hp-hr NOx over the composite FTP and RMC. NOx conversion efficiency will also be compared with respect to N2O formation and NH3 slip.

As vehicle emissions regulations become increasingly stringent, there is a growing need to accurately model aftertreatment systems to aid in the development of ultra-low NOx vehicles. Common solutions to this problem include the development of complex chemical models or expansive neural networks. This paper aims to present the development process of a simpler Selective Catalytic Reduction (SCR) conversion efficiency Simulink model for the purposes of modeling tail pipe NOx emission levels based on various inputs, temperature shifts and SCR locations, arrangements and/or sizes in the system. The main objective is to utilize this model to predict tail pipe NOx emissions of the EPA Federal Test Procedures for heavy-duty vehicles. The model presented within is focused exclusively on heavy-duty application compression ignition engines and their corresponding aftertreatment setups.

Current legislative trends regarding diesel emissions are striving to achieve two seemingly competing goals: simultaneously lowering NOx and greenhouse gas (GHG) emissions. These two goals are considered at odds since lower GHG emissions (e.g. CO2) is achieved via high combustion efficiency that result in higher engine out NOx emissions and lower exhaust gas temperatures [1, 2]. Conversely, NOx reduction technologies such as SCR require temperatures above 200°C for dosing the reductant (DEF) [3, 4, 5] as well as for high conversion efficiencies [1, 2, 6, 7, 8, 9]. Dosing DEF requires injection pressures around 5 bar to ensure proper penetration into the exhaust stream as well as generate the appropriate spray pattern and droplet sizes. Dosing DEF generally requires long mixing and/or high turbulence (high restriction) areas so that the aqueous urea solution can be converted into gaseous NH3 without deposit formation [8, 10, 11, 12, 13, 14, 15].

Formation of urea injection related deposits in a heavy-duty urea-SCR system was studied using an engine lab setup. The exhaust system was instrumented with thermocouples to track temperature changes caused by the liquid spray. Impact of operating parameters (exhaust and ambient temperature, urea solution injection rate) and system design modification (insulation, wiremesh insert) on the temperature profiles and deposit quantities was studied. Deposits were found in all tests conducted under typical exhaust temperatures. Deposition rate increased with lower exhaust and ambient temperature, and with higher injection rate. Mixer insulation and wiremesh upstream of the mixer reduced the deposits.

In this study, a 15-L heavy-duty diesel engine and an emission control system consisting of diesel oxidation catalysts, NOx adsorber catalysts, and diesel particle filters were evaluated over the course of a 2000 hour aging study. The work is a follow-on to a previously documented development effort to establish system regeneration and sulfur management strategies. The study is one of five projects being conducted as part of the U.S. Department of Energy's Advanced Petroleum Based Fuels - Diesel Emission Control (APBF-DEC) activity. The primary objective of the study was to determine if the significant NOx and PM reduction efficiency (>90%) demonstrated in the development work could be maintained over time with a 15-ppm sulfur diesel fuel. The study showed that high NOx reduction efficiency can be restored after 2000 hours of operation and 23 desulfation cycles.

This paper outlines the development and integration of an advanced emission control system with a modern heavy-duty diesel engine for use in a series of catalyst aging tests. The project that is discussed is one of several being conducted under the Department of Energy's Advanced Petroleum-Based Fuels - Diesel Emission Control (APBF-DEC) activity. This government/industry collaboration is examining how systems of advanced fuels, engines, and emission control systems can deliver significantly lower emissions while maintaining or improving vehicle fuel economy. This project is using a Cummins ISX EGR engine (15 L) with a secondary fuel injection system to enable NOx adsorber catalyst regeneration. Development of the strategies for NOx regeneration and sulfur removal as well as integration of the emission control hardware is discussed. Performance of oven aged systems tested over transient and steady-state cycles is summarized.