Search Results

In the present study, Large Eddy Simulations (LES) have been performed with a 3D model of a step nozzle injector, using n-pentane as the injected fluid, a representative of the high-volatility components in gasoline. The influence of fuel temperature and injection pressure were investigated in conditions that shed light on engine cold-start, a phenomenon prevalent in a number of combustion applications, albeit not extensively studied. The test cases provide an impression of the in-nozzle phase change and the near-nozzle spray structure across different cavitation regimes. Results for the 20oC fuel temperature case (supercavitating regime) depict the formation of a continuous cavitation region that extends to the nozzle outlet. Collapse-induced pressure wave dynamics near the outlet cause a transient entrainment of air from the discharge chamber towards the nozzle.

Reported in the current paper is a study into the cycle efficiency effects of utilising a complex valvetrain mechanism in order to generate variable in-cylinder charge motion and therefore alter the dilution tolerance of a Direct Injection Spark Ignition (DISI) engine. A Jaguar Land Rover Single Cylinder Research Engine (SCRE) was operated at a number of engine speeds and loads with the dilution fraction varied accordingly (excess air (lean), external Exhaust Gas Residuals (EGR) or some combination of both). For each engine speed, load and dilution fraction, the engine was operated with either both intake valves fully open - Dual Valve Actuation (DVA) - or one valve completely closed - Single Valve Actuation (SVA) mode. The engine was operated in DVA and SVA modes with EGR fractions up to 20% with the excess air dilution (Lambda) increased (to approximately 1.8) until combustion stability was duly compromised.

The design of a Diesel injector is a key factor in achieving higher engine efficiency. The injector's fuel atomisation characteristics are also critical for minimising toxic emissions such as unburnt Hydrocarbons (HC). However, when developing injection systems, the small dimensions of the nozzle render optical experimental investigations very challenging under realistic engine conditions. Therefore, Computational Fluid Dynamics (CFD) can be used instead. For the present work, transient, Volume Of Fluid (VOF), multiphase simulations of the flow inside and immediately downstream of a real-size multi-hole nozzle were performed, during and after the injection event with a small air chamber coupled to the injector downstream of the nozzle exit. A Reynolds Averaged Navier-Stokes (RANS) approach was used to account for turbulence. Grid dependency studies were performed with 200k-1.5M cells.

Flash-boiling of sprays may occur when a superheated liquid is discharged into an ambient environment with lower pressure than its saturation pressure. Such conditions normally exist in direct-injection spark-ignition engines operating at low in-cylinder pressures and/or high fuel temperatures. The addition of novel high volatile additives/fuels may also promote flash-boiling. Fuel flashing plays a significant role in mixture formation by promoting faster breakup and higher fuel evaporation rates compared to non-flashing conditions. Therefore, fundamental understanding of the characteristics of flashing sprays is necessary for the development of more efficient mixture formation. The present computational work focuses on modelling flash-boiling of n-Pentane and iso-Octane sprays using a Lagrangian particle tracking technique.

This paper addresses the need for fundamental understanding of the mechanisms of fuel spray formation and mixture preparation in direct injection spark ignition (DISI) engines. Fuel injection systems for DISI engines undergo rapid developments in their design and performance, therefore, their spray breakup mechanisms in the physical conditions encountered in DISI engines over a range of operating conditions and injection strategies require continuous attention. In this context, there are sparse data in the literature on spray formation differences between conventionally drilled injectors by spark erosion and latest Laser-drilled injector nozzles. A comparison was first carried out between the holes of spark-eroded and Laser-drilled injectors of same nominal type by analysing their in-nozzle geometry and surface roughness under an electron microscope.

One of the latest advancements in injector technology is laser drilling of the nozzle holes. In this context, the spray formation and atomisation characteristics of gasoline, ethanol and 1-butanol were investigated for a 7-hole spark eroded (SE) injector and its ‘direct replacement’ Laser-drilled (LD) injector using optical techniques. In the first step of the optical investigation, high-speed spray imaging was performed in a quiescent injection chamber with global illumination using diffused Laser light. The images were statistically analyzed to obtain spray penetration, spray tip velocity and spray ‘cone’ angles. Furthermore, droplet sizing was undertaken using Phase Doppler Anemometry (PDA). A single spray plume was isolated for this analysis and measurements were obtained across the plume at a fixed distance from the nozzle exit.

This paper presents a study of the combustion mechanism of hydrous and anhydrous ethanol in comparison to iso-octane and gasoline fuels in a single-cylinder spark-ignition research engine operated at 1000 rpm with 0.5 bar intake plenum pressure. The engine was equipped with optical access and tests were conducted with both Port Fuel Injection (PFI) and Direct Injection (DI) mixture preparation methods; all tests were conducted at stoichiometric conditions. The results showed that all alcohol fuels, both hydrous and anhydrous, burned faster than iso-octane and gasoline for both PFI and DI operation. The rate of combustion and peak cylinder pressure decreased with water content in ethanol for both modes of mixture preparation. Flame growth data were obtained by high-speed chemiluminescence imaging. These showed similar trends to the mass fraction burned curves obtained by in-cylinder heat release analysis for PFI operation; however, the trend with DI was not as consistent as with PFI.

International obligations to reduce carbon dioxide emissions and requirements to strengthen security of fuel supply, indicate a need to diversify towards the use of cleaner and more sustainable fuels. Hydrogen has been recommended as an encouraging gaseous fuel for future road transportation since with reasonable modifications it can be burned in conventional internal combustion engines without producing carbon-based tailpipe emissions. Direct injection of hydrogen into the combustion chamber can be more preferable than port fuel injection since it offers advantages of higher volumetric efficiency and can eliminate abnormal combustion phenomena such as backfiring. The current work applied a fully implicit computational methodology along with the Reynolds-Averaged Navier-Stokes (RANS) approach to study the mixture formation and combustion in a direct-injection spark-ignition engine with hydrogen fuelling.

Particulate emissions are of growing concern due to health impacts. Many urban areas around the world currently have particulate matter levels exceeding the World Health Organisation safe limits. Gasoline engines, especially when equipped with direct injection systems, contribute to this pollution. In recognition of this fact European limits on particulate mass and number are being introduced. A number of ways to meet these new stringent limits have been under investigation. The focus of this paper is on particulate emissions reduction through improvements in fuel delivery. This investigation is part of the author's ongoing particulate research and development that includes optical engine spray and combustion visualisation, CFD method development, engine and vehicle testing with the aim to move particulate emission development upstream in the development process.

Hydrogen has been largely proposed as a possible fuel for internal combustion engines. The main advantage of burning hydrogen is the absence of carbon-based tailpipe emissions. Hydrogen's wide flammability also offers the advantage of very lean combustion and higher engine efficiency than conventional carbon-based fuels. In order to avoid abnormal combustion modes like pre-ignition and backfiring, as well as air displacement from hydrogen's large injected volume per cycle, direct injection of hydrogen after intake valve closure is the preferred mixture preparation method for hydrogen engines. The current work focused on computational studies of hydrogen injection and mixture formation for direct-injection spark-ignition engines. Hydrogen conditions at the injector's nozzle exit are typically sonic.

In-cylinder air flow structures are known to play a major role in mixture preparation and engine operating limits for DISI engines. In this paper PIV was undertaken on in-cylinder flow fields for three different planes of measurement in the intake and compression strokes of a DISI engine for a low-load engine operating condition at 1500 RPM, 0.5 bar inlet plenum pressure (World Wide Mapping Point). One of these planes was vertical, cutting through the centrally located spark plug (tumble plane); the other two planes were horizontal, one close to TDC (10 mm below fire face) and the other one close to mid stroke (50 mm below fire face). Statistical analysis was undertaken on the numbers of cycles needed to determine ensemble average flow-field and turbulent kinetic energy maps with up to 1200 cycles considered. The effect of engine head temperature was also examined by obtaining flow fields using PIV with the engine head coolant held at 20 °C and 80 °C.

Spray characteristics of injectors depend on, among other factors, not only the level of turbulence upstream of the nozzle plate, but also on whether cavitation arises. "Bulk" cavitation, by which we mean cavitation which arises far from walls and thus far from streamline curvature associated with salient points on a wall, has not been investigated thoroughly experimentally and moreover it is quite challenging to predict by means of computational fluid dynamics. Information about the effect of the injector geometry on the formation of bulk cavitation and quantitative measurements of the flow field that promotes this phenomenon in gasoline injectors does not exist and this forms the background to this work. Evolution of bulk cavitation was visualized in two gasoline multi-hole injectors by means of a fast camera.

This work involved study of the effects of alcohol blends on combustion, fuel economy and emissions in a single cylinder research engine equipped with a mechanical fully variable valvetrain on the inlet and variable valve timing on the exhaust. A number of splash blends of gasoline, iso-octane, ethanol and butanol were examined during port fuel injected early inlet valve closing operation, both with and without variable valve timing. Under low valve overlap conditions, it was apparent that the inlet valve durations/lifts required for full unthrottled operation were remarkably similar for the wide range of blends studied. However, with high valve overlap differences in burning velocities and internal EGR tolerances warranted changes in these valve settings.

Hydrogen has been largely proposed as a possible alternative fuel for internal combustion engines. Its wide flammability range allows higher engine efficiency with leaner operation than conventional fuels, for both reduced toxic emissions and no CO2 gases. Independently, Homogenous Charge Compression Ignition (HCCI) also allows higher thermal efficiency and lower fuel consumption with reduced NOX emissions when compared to Spark-Ignition (SI) engine operation. For HCCI combustion, a mixture of air and fuel is supplied to the cylinder and autoignition occurs from compression; engine is operated throttle-less and load is controlled by the quality of the mixture, avoiding the large fluid-dynamic losses in the intake manifold of SI engines. HCCI can be induced and controlled by varying the mixture temperature, either by Exhaust Gas Recirculation (EGR) or intake air pre-heating.

This experimental work was concerned with the combination of internal EGR with an early inlet valve closure strategy for improved part-load fuel economy. The experiments were performed in a new spark-ignited thermodynamic single cylinder research engine, equipped with a mechanical fully variable valvetrain on both the inlet and exhaust. During unthrottled operation at constant engine speed and load, increasing the mass of trapped residual allowed increased valve duration and lift to be used. In turn, this enabled further small improvements in gas exchange efficiency, thermal efficiency and hence indicated fuel consumption. Such effects were quantified under both port and homogeneous central direct fuel injection conditions. Shrouding of the inlet ports as a potential method to increase in-cylinder gas velocities has also been considered.

Current developments in fuels and emissions regulations are resulting in increasingly severe operating environment for the injection system. Formation of deposits within the holes of the injector nozzle or on the outside of the injector tip may have an adverse effect on overall system performance. This paper provides a critical review of the current understanding of the main factors affecting deposit formation. Two main types of engine test cycles, which attempt to simulate field conditions, are described in the literature. The first type involves cycling between high and low load. The second involves steady state operation at constant speed either at medium or high load. A number of influences on the creation of deposits are identified. This includes fouling through thermal condensation and cracking reactions at nozzle temperatures of around 300°C. Also the design of the injector holes is an influence, because it can influence cavitation.

Recent pressures on vehicle manufacturers to reduce their average fleet levels of CO2 emissions have resulted in an increased drive to improve fuel economy and enable use of fuels developed from renewable sources that can achieve a net reduction in the CO2 output of each vehicle. The most popular choice for spark-ignition engines has been the blending of ethanol with gasoline, where the ethanol is derived either from agricultural or cellulosic sources such as sugar cane, corn or decomposed plant matter. However, other fuels, such as butanol, have also arisen as potential candidates due to their similarities to gasoline, e.g. higher energy density than ethanol. To extract the maximum benefits from these new fuels through optimized engine design and calibration, an understanding of the behaviour of these fuels in modern engines is necessary.

In recent times regulatory pressure to reduce CO2 emissions has driven research towards looking at blending fossil fuels with alternatives such as crop-produced alcohols. The alcohol of interest in this paper is ethanol and it was studied in mixtures with gasoline and iso-octane in an optical spark-ignition engine, running at 1500 RPM at low-load operation with 0.5 bar absolute intake plenum pressure. Specifically, tests involved fuels of 100% gasoline and 100% iso-octane, so that differences between multi and single-component fuels could be compared within this environment. A mixture of 25% ethanol with 75% iso-octane was also tested and compared. Finally, mixtures of high-percentage of ethanol (85% ethanol) in gasoline and in iso-octane were used in the study and compared. Tests were undertaken using a standard port injection system as well as a direct injection system so an appraisal of both mixture preparation methods could be made.

In an attempt to study the numerous contributors towards cyclic variations in combustion in a direct injection spark ignition engine, simultaneous high-speed imaging of fuel injection and flame growth are undertaken on a crank-angle resolved basis in a single-cylinder optical research engine. Batches of images from 100 consecutive cycles are acquired for all conditions with synchronised in-cylinder pressure logging. The engine is motored and fired at stoichiometric conditions at 1500 RPM under part-load and wide-open-throttle conditions (0.5-1.0 bar intake pressure), with injection timing set early in the intake stroke to promote homogeneous mixture formation with a centrally mounted multi-hole injector. Liquid impingement is observed on the cylinder walls and on the piston crown with early intake injection and multiple injection strategies are employed in an attempt to reduce impingement and alter mixture preparation and subsequent combustion.

Extensive literature exists on spray development, mixing and combustion regarding engine modeling and diagnostics using single-component and model fuels. However, often the variation in data between different fuels, particularly relating to spray development and its effect on combustion, is neglected or overlooked. By injecting into a quiescent chamber, this work quantifies the differences in spray development from a multi-hole direct-injection spark-ignition engine injector for two single-component fuels (iso-octane and n-pentane), a non-fluorescing multi-component model fuel which may be used for in-cylinder Laser Induced Fluorescence experiments, and several grades of pump gasoline (with and without additives). High-speed recordings of the sprays were made for a range of fuel temperatures and gas pressures. It is shown that a fuel temperature above that of the lowest boiling point fraction of the tested fuel at the given gas pressure causes a convergence of the spray plumes.