Search Results

Crankshaft is a dynamic component that copes with elevated alternating stresses. In order to ensure the service reliability, fillet rolling process is being applied. The state of the art empirical assumptions to consider the effect of fillet rolling process on crankshaft fatigue are conservative. This leads to an over-engineering of the crankshaft. However, calculation of the compressive residual stresses due to surface treatment is a demanding task. The quality of the durability analysis can only be increased by an accurate consideration of the fillet rolling effect. Therefore, Hegenscheidt-MFD, FEV Motorentechnik and Institute for Combustion Engines (VKA) cooperated to enlighten the phenomenon of the fillet rolling process. Process calculations are applied and validated by the measurements and tests. The calculated residual stresses are then superposed with the dynamic loads calculated by FEV Virtual Engine.

Due to increasing demand for environment friendly vehicles with better fuel economy and strict legislations on greenhouse gas emissions, lightweight design has become one of the most important issues concerning the automobile industry. Within the scope of this work lightweight design potentials that a conventional single cylinder engine crankshaft offers are researched through utilization of structural optimization techniques. The objective of the study is to reduce mass and moment of inertia of the crankshaft with the least possible effect on the stiffness and strength. For precise definition of boundary conditions and loading scenarios multi body simulations are integrated into the optimization process. The loading conditions are updated at the beginning of each optimization loop, in which a multi body simulation of the output structure from the previous optimization loop is carried out.

This paper introduces a new approach based on a statistical investigation and finite element analysis (FEA) methodology to predict the crankshaft torsional stiffness and stress concentration factors (SCF) due to torsion and bending which can be used as inputs for simplified crankshaft multibody models and durability calculations. In this way the reduction of the development time and effort of passenger car crankshafts in the pre-layout phase is intended with a least possible accuracy sacrifice. With the designated methodology a better approximation to reality is reached for crank torsional stiffness and SCF due to torsion and bending compared with the empirical approaches, since the prediction does not depend on the component tests with limited numbers of specimen, as in empirical equations, but on various FE calculations.

This paper introduces different modeling approaches of crankshafts, compares the refinement levels and discusses the difference between the results of the crankshaft durability calculation methodologies. A V6 crankshaft is considered for the comparison of the refinement levels depending on the deviation between the signals such as main bearing forces and deflection angle. Although a good correlation is observed between the results in low speed range, the deviation is evident through the mid to high speed ranges. The deviation amplitude differs depending on the signal being observed and model being used. An inline 4 crankshaft is considered for the comparison of the durability results. The analysis results show that the durability potential is underestimated with a classical crankshaft calculation approach which leads to a limitation of maximum speed of 5500 rpm.

Due to the contradiction of the market demands and legal issues OEMs are forced to invest in finding concepts that assure high fuel economy, low exhaust emissions and high specific power at the same time. Since mechanical losses may amount up to 10 % of the fuel energy, a key to realise such customer/government specific demands is the improvement of the mechanical performance of the engines, which comprises mainly friction decrease and lightweight design of the engine parts. In order to achieve the mentioned objectives, it has to be checked carefully for each component whether the design potentials are utilized. Many experimental studies show that there is still room for optimization of the cranktrain parts, especially for the crankshaft. A total exploitation of the crankshaft potentials is only possible with advanced calculation approaches that ensure the component layout within design limits.

Torque and performance requirements of Diesel engines are continually increasing while lower emissions and fuel consumption are demanded, thus increasing thermal and mechanical loads of the main components. The level of peak firing pressure is approaching 200 bar (even higher in Heavy Duty Diesel engines), consequently, a structural optimization of crankcase, crank train components and in particular of the cylinder head is required to cope with the increasing demands. This report discusses design features of cylinder head concepts which have the capability for increasing thermal and mechanical loads in modern Diesel engines

Due to the rapidly increasing raw oil price the reduction of fuel consumption has become one of the most important targets for the development of modern passenger car engines. After large progress has been achieved in the combustion process development - CAE has been one of the keys to success - nowadays further potential is being investigated. The mechanical friction is very much in the focus of the engine development engineers. While in the Valve Train the potential of roller contacts and surface treatment is the main development direction, in the cranktrain the reduction of bearing diameters is being investigated. Due to increasing specific loads on the crankshaft there are clear limits. At the piston group the potential is almost untouched. While optimizations of the piston skirt contour or the ring pack bring up the risk of negative influences on blow by and oil consumption, the application of a crank offset is an easy design measure having almost no risks.

The loads on the plain bearings of modern combustion engines increase continuously. Reasons for this development are increasing engine speeds on gasoline engines, growing cylinder peak pressures at diesel engines and both combined with the steady trend toward light weight concepts. The still significantly increasing power output of modern engines has to be combined with actions reducing the engine friction losses, as for example smaller bearing dimensions or lower engine oil viscosities. At the same time the comfort, lifetime and engine service interval targets are aggravating boundary conditions. This development leads to the point, where former approaches toward plain bearing layout reach their systematic limitations - a first indication are bearing failures, which occur even though all conventional layout criteria's are fulfilled. Further effects need to be considered to simulate the behavior of the plain bearing under the boundary conditions of a fired combustion engine.

The combination of multi purpose software with powertrain specific application codes allows highly flexible simulation models, which are independent on the specific engine concept. Related to the requests those models may be refined or simplified during the simulation process. Finally a fully coupled 3D dynamic simulation including flexible components is performed to assess the engine crankshaft's durability. To take into account the stiffness of the cranktrain components and the cylinder block at first a linear Finite Element Analysis (FEA) simulation is performed. Via modal reduction the complete deformation order information of the FEA simulation are reduced to the necessary information for the dynamic Multi Body System (MBS) simulation [1, 2]. All main boundary conditions of the system, e. g. gas forces, oil temperature or driveline application are taken into account.

A combined finite element method (FEM), multibody system simulation (MSS), and hydrodynamic (HD) bearing simulation technique can be applied to solve for engine crankshaft and cylinder block dynamics. The cylinder block and crankshaft are implemented in the MSS program as flexible FEM structures. The main bearing oil film reaction is described in the MSS program by a pre-calculated reaction force database. The results are displacements and deformations of the crank train parts and the main bearing reaction forces. Verification of the tool was carried out by comparison of main bearing cap accelerations to measured data.