Search Results

To evaluate vehicle crash performance in the early design stages, a reliable fracture model is needed in crash simulations to predict material fracture initiation and propagation. In this paper, a generalized incremental stress state dependent damage model (GISSMO) in LS-DYNA® was calibrated and validated for a 780-MPa third generation advanced high strength steels (AHSS), namely 780 XG3TM steel that combines high strength and ductility. The fracture locus of the 780 XG3TM steel was experimentally characterized under various stress states including uniaxial tension, shear, plane strain and equi-biaxial stretch conditions. A process to calibrate the parameters in the GISSMO model was developed and successfully applied to the 780 XG3TM steel using the fracture test data for these stress states.

Edge flanging represents one of the forming modes employed in multistage forming, and advanced high strength steels (AHSS) are more prone to edge cracking during sheared edge flanging than the conventional high strength steels (HSS) and mild steels. The performance of the sheared edge in flanging operation depends on the remaining ductility of the material in the sheared edge after the work hardening (WH) and damage produced by blanking and subsequent forming operations. Therefore, it is important to analyze the effect of work hardening produced by blanking and subsequent forming operations prior to edge flanging on the edge flanging performance. In this study, the effect of different forming operation sequences prior to edge flanging on the edge flanging performance was analyzed for a dual phase 780 steel.

Gas Metal Arc Welding (GMAW) is widely employed for joining relatively thick sheet steels in automotive body-in-white structures and frames. The GMAW process is very flexible for various joint geometries and has relatively high welding speed. However, fatigue failures can occur at welded joints subjected to various types of loads. Thus, vehicle design engineers need to understand the fatigue characteristics of welded joints produced by GMAW. Currently, automotive structures employ various advanced high strength steels (AHSS) such as dual-phase (DP) and transformation-induced plasticity (TRIP) steels to produce lighter vehicle structures with improved safety performance and fuel economy, and reduced harmful emissions. Relatively thick gages of AHSS are commonly joined to conventional high strength steels and/or mild steels using GMAW in current body-in-white structures and frames.

In the North American automotive industry, various advanced high strength steels (AHSS) are used to lighten vehicle structures, improve safety performance and fuel economy, and reduce harmful emissions. Relatively thick gages of AHSS are commonly joined to conventional high strength steels and/or mild steels using Gas Metal Arc Welding (GMAW) in the current generation body-in-white structures. Additionally, fatigue failures are most likely to occur at joints subjected to a variety of different loadings. It is therefore critical that automotive engineers need to understand the fatigue characteristics of welded joints. The Sheet Steel Fatigue Committee of the Auto/Steel Partnership (A/S-P) completed a comprehensive fatigue study on GMAW joints of both AHSS and conventional sheet steels including: DP590 GA, SAE 1008, HSLA HR 420, DP 600 HR, Boron, DQSK, TRIP 780 GI, and DP780 GI steels.

To improve the energy absorption capacity of front-end structures during a vehicle crash, a novel 12-sided cross-section was developed and tested. Computer-aided engineering (CAE) studies showed superior axial crash performance of the 12-sided component over more conventional cross-sections. When produced from advanced high strength steels (AHSS), the 12-sided cross-section offers opportunities for significant mass-savings for crash energy absorbing components such as front or rear rails and crush tips. In this study, physical crash tests and CAE modeling were conducted on tapered 12-sided samples fabricated from AHSS. The effects of crash trigger holes, different steel grades and bake hardening on crash behavior were examined. Crash sensitivity was also studied by using two different part fabrication methods and two crash test methods. The 12-sided components showed regular folding mode and excellent energy absorption capacity in axial crash tests.

In an attempt to develop gas-metal arc-welded (GMAW) sheet steel coupons with tightly controlled weld geometry for fatigue testing, it was discovered that the very slight changes in welding process parameters strongly influence the weld geometry. The extent of fusion zone, horizontal and vertical leg lengths, and depth of penetration were considered to define the weld geometry. In order to elucidate the sensitivity of weld geometry to process parameters, a study was conducted on welding of various types of specimens. The paper reports the results of variations in weld geometry with small changes in process parameters. In addition, through several examples, it is demonstrated that variability in the weld geometry is unavoidable even with very tight weld process control.

As a result of the increasing usage of high strength steels in automotive body structures, a number of formability issues, particularly bend and edge stretch failures, have come to the forefront of attention of both automotive OEMs and steel makers. This investigation reviews these stamping problems and attempts to identify how certain material properties and microstructural features relate to forming behavior. Various types of dual phase steels were evaluated in terms of tensile, bending, hole expansion, limiting dome height, and impact properties. In addition, the key microstructural differences of each grade were characterized. In order to understand the material behavior under practical conditions, stamping trials were conducted using actual part shapes. It was concluded that material properties can be optimized to maximize local formability in stamping applications. The results also emphasize that the dual phase classification can encompass a broad range of property variations.

Drop tower crash tests in a three-point bending configuration were carried out on spot welded box sections, adhesive bonded box sections, and laser welded cylindrical tubes made from a variety of advanced high strength steels. In the tests, a 147-kg indenter with a 28-cm diameter impacts the specimen at approximately 6 m/s, and the bending loads and energy absorption are determined. The results show that the maximum bending loads best correlate to the product of yield strength and thickness-squared, while the energy absorbed over 10-cm displacement best correlates to ultimate tensile strength times thickness-squared. As such, higher strength steels can be used to improve crash performance without increasing weight or to maintain crash performance with weight reduction. Other significant findings of the study are as follows. Bake hardening alone may improve bending crash performance slightly, while cold rolling and baking does not.

Because of increasing fuel costs and environmental concerns, the automotive industry is under enormous pressure to reduce vehicle weight. One strategy, downgaging, substitutes a reduced gage (thickness) steel in place of a thicker one, and is usually accompanied by a material grade change to a higher strength steel. Thus, Advanced High Strength Steels (AHSS) are increasingly used for lightweight automotive body structures. The critical durability concern with steels is the spot welds used to join them, since fatigue cracks in body structures preferentially initiate at spot welds. Hence, the Auto/Steel Partnership (A/SP) Sheet Steel Fatigue Taskforce undertook an investigation both to study the fatigue performance of AHSS spot welds, and to generate data for OEM durability analysis. The study included seven AHSS grades and, for comparison, mild steels and a conventional High Strength Low Alloy grade, HSLA340.

Axial drop tower crash tests were carried out on a variety of 70-mm outer-diameter continuous-welded cylindrical steel tubes with several thicknesses (t). Ultimate tensile strength (UTS) ranged from less than 300 MPa for a fully stabilized steel to greater than 800 MPa for the advanced high strength steels (AHSS). In the tests, a 520-kg weight is dropped from a height of 3.3 meters to achieve impact velocities of 6.1 to 6.7 m/s (14 to 15 mph). Load and acceleration data are recorded as a function of time as the tube is crushed axially. The results show that, for a given impact condition, the peak and average crush loads of a steel tube is directly proportional to UTS × t2, while axial crush distance is inversely proportional to UTS × t2. As such, crash deformation can be reduced by substituting higher strength steels of the same thickness, or existing crash deformation can be maintained and weight reduction achieved by substituting higher strength steels with reduced thickness.

The influence of strain rate on work hardening behavior has been determined for a variety of high strength steels including high-strength low-alloy (HSLA), dual phase (DP), and transformation-induced plasticity (TRIP) steels. Tensile testing was performed at true strain rates of 10-3 s-1 and 1.0 s-1 to represent laboratory testing conditions and dynamic press-forming operations, respectively. Work hardening behavior is described by the conventional strain hardening exponent (n-value), the work hardening rate (dσ/dε), and the Shape-Tilt-Strength (STS) equation as an alternative approach. The effects of deformation temperature and temperature rise during deformation (adiabatic heating) on work hardening are also evaluated. Increasing the strain rate generally increases the work hardening rate at smaller strains, which may contribute to a broader initial strain distribution in press forming.

Steel-plastic-steel (SPS) laminated sheet materials can be utilized in certain automotive applications to achieve significant weight savings over “conventional” sheet steels. Three SPS laminates were produced using various combinations of light gage steel skins and polypropylene cores. Compared to homogeneous steels, density reductions of 35 to 46 percent were achieved. Benefiting from the ductility of their steel skins, SPS laminates can posses adequate formability for typical automotive sheet applications. Furthermore, the forming limit curves can be predicted using the work hardening exponent and thickness of the composite laminate. In three-point bending, the elastic stiffness of SPS laminates is nearly equivalent to that of monolithic steels of the same thickness. Thus, weight reductions similar to those of aluminum alloys can be achieved utilizing laminates in stiffness-critical applications.