Search Results

Mild hybridisation, using a 48 V system architecture, offers fuel consumption benefits approaching those achieved using high-voltage systems at a much lower cost. To maximise the benefits from a 48 V mild-hybrid system, it is desirable to recuperate during deceleration events at as high a power level as possible, whilst at the same time having a relatively compact and low cost system. This paper examines the particular requirements of the battery pack for such a mild-hybrid application and discusses the trade-offs between battery power capabilities and possible fuel consumption benefits. The technical challenges and solutions to design a 48 V mild-hybrid battery pack are presented with special attention to cell selection and the thermal management of the whole pack. The resulting battery has been designed to achieve a continuous-power capability of more than 10 kW and a peak-power rating of up to 20 kW.

Computer programs that simulate the wave propagation phenomena involved in manifold tuning mechanisms are used extensively in the design and development of internal combustion engines. Most comprehensive engine simulation programs are based on the governing equations of one-dimensional gas flow as these provide a reasonable compromise between modelling accuracy and computational speed. The propagation of pressure waves through pipe junctions is, however, an intrinsically multi-dimensional phenomenon. The modelling of such junctions within a one-dimensional simulation represents a major challenge, since the geometry of the junction cannot be fully represented but can have a major influence on the flow. This paper introduces a new pressure-loss junction model which can mimic the directionality imposed by the angular relationship of the pipes forming a multi-pipe junction. A simple technique for estimating the pressure-loss data required by the model is also presented.

Turbulent Jet Ignition is an advanced spark initiated pre-chamber combustion system for otherwise standard spark ignition engines found in current passenger vehicles. This next generation pre-chamber design simply replaces the spark plug in a conventional spark ignition engine. Turbulent Jet Ignition enables very fast burn rates due to the ignition system producing multiple, widely distributed ignition sites, which consume the main charge rapidly. This high energy ignition results from the partially combusted (reacting) pre-chamber products initiating combustion in the main chamber. The distributed ignition sites enable relatively small flame travel distances enabling short combustion durations and high burn rates. Multiple benefits include extending the knock limit and initiating combustion in very dilute mixtures (excess air and or EGR), with dilution levels being comparable to other low temperature combustion technologies (HCCI), without the complex control drawbacks.

Current focus on techniques to reduce the tailpipe carbon dioxide (CO₂) emissions of road vehicles is increasing the interest in hybrid and electric vehicle technologies. Pure electric vehicles require bulky, heavy, and expensive battery packs to enable an acceptable drivable range to be achieved. Extended-range electric vehicles (E-REVs) partly overcome the limitations of current battery technology by having an onboard fuel converter that converts a liquid fuel, such as gasoline, into electrical energy whilst the vehicle is driving. Thus enabling the traction battery storage capacity to be reduced, whilst still maintaining an acceptable vehicle range. This paper presents results from a drive style analysis toolset that enable US and EU fleet vehicle drive data to be categorized and compared. Key metrics, such as idle frequency, idle duration, vehicle speed, and vehicle acceleration are analyzed.

MAHLE Powertrain has built a range-extended electric vehicle demonstrator, with a series hybrid configuration. The vehicle is intended to operate predominantly purely electrically. Once the battery state of charge is depleted a gasoline engine (range extender) is activated to provide the energy required to propel the vehicle. As part of the continuing development of this vehicle, MAHLE Powertrain has recorded data during real world driving, with the aim of further investigating the actual usage a range-extended electric vehicle under non-laboratory test conditions. The vehicle is instrumented with a data acquisition system which records physical parameters, for example coolant temperatures, as well as CAN-based data from the engine and vehicle management systems.

MAHLE has developed a heavily downsized demonstrator engine to explore the limits, and potential benefits, of engine downsizing. The 1.2 litre, 3-cylinder, MAHLE downsizing (Di3) engine, in conjunction with an Aeristech 48 V electric supercharger (eSupercharger, eSC), achieves a BMEP level of 35 bar and a specific power output in excess of 160 kW/litre. The eSupercharger enables high specific power output, good low speed torque and excellent transient response. The resulting heavily downsized engine has been installed into a demonstrator vehicle that also features 48 V mild hybridization. At specific power output levels above 90 kW/litre the engine is operated with excess fuel in order to protect the turbine from excessive exhaust gas temperatures. In this analytical study, the boosting system requirements to maintain lambda 1 fuelling, via the use of EGR, across the entire engine operating map for the eSupercharged version of the MAHLE Di3 engine, have been explored.

Driven by legislation, economics and increasing societal awareness, engine and vehicle manufacturers are facing increasing pressure to reduce vehicle emissions and deliver improved fuel economy. Significant reductions in carbon dioxide (CO2) emissions will need to be achieved to meet these requirements whilst at the same time satisfying the more stringent forthcoming emissions regulations. This focus on techniques to reduce the tailpipe CO2 is increasing the interest in novel combustion technologies, including dilute combustion in gasoline engines. The pre-chamber based jet ignition concept produces high energy jets of partially combusted species that induce ignition at multiple locations in the main combustion chamber to enable rapid, stable combustion, even with dilute mixtures. The present study focusses on the beneficial synergies of the pre-chamber system with high geometric compression ratio (CR), Miller cycle operation and cooled external exhaust gas recirculation (EGR).

In order to achieve the required future CO2 reduction targets, significant further development of both gasoline and diesel engines is required. One of the main methods to achieve this with the gasoline engine in the short to medium term is through the application of engine downsizing, which has resulted in numerous downsized engines already being brought to production. It is, however, considered that there is still significant further CO2 reduction potential through continued development of this technology. This paper considers the future development of gasoline engine downsizing in the short to medium term and the various technologies that can be applied to further increase the efficiency of operation. As such this paper covers, among other areas, fundamental engine layout and design, alternative boosting systems, methods of increasing part load efficiency and vehicle modelling, and uses analysis tools and engine test results to show the benefits achievable.

The automobile industry is under intense pressure to reduce carbon dioxide (CO2) emissions of vehicles. There is also increasing pressure to reduce the other tail-pipe emissions from vehicles to combat air pollution. Electric powertrains offer great potential for eliminating tailpipe CO2 and all other tailpipe emissions. However, current battery technology and recharging infrastructure still present limitations for some applications, where a continuous high-power demand is required. Furthermore, not all markets have the infrastructure to support a sizeable electric fleet and until the grid energy generation mix is of a sufficiently low carbon intensity, then significant vehicle life-cycle CO2 savings could not be realized by the Battery Electric Vehicles. This investigation examines the effects of combustion, efficiencies, and emissions of two alcohol fuels that could help to significantly reduce CO2 in both tailpipe and the whole life cycle.

Charge-coolers have a significant effect on the performance of turbocharged internal combustion engines. For a comprehensive simulation of internal combustion engines fitted with such devices it is important to model the whole of the manifold system. A wave-action model of a charge-cooler boundary is proposed, together with a methodology for predicting the heat transfer coefficient of the device. This approach enables the instantaneous effectiveness of the charge-cooler to be predicted as a function of the mass flow rate through the device.

Current focus on techniques to reduce the tailpipe CO₂ emissions of road vehicles is increasing the interest in hybrid and electric vehicle technologies. Pure electric vehicles require bulky, heavy, and expensive battery packs to enable an acceptable drive-able range to be achieved. Extended-range electric vehicles (E-REV) partly overcome the limitations of current battery technology by having a "range extender" unit, which consists of an onboard fuel converter that converts a liquid fuel, such as gasoline, into electrical energy whilst the vehicle is driving. This enables the traction battery storage capacity to be reduced, whilst still maintaining an acceptable vehicle driving range. In a previous paper the power requirement of a range extender for a typical C segment passenger car was investigated using drive-cycle modeling over real-world cycles. This paper presents the detailed design of the range extender engine.

Extreme engine downsizing is a modern solution aimed towards the goal of meeting new emissions regulations for internal combustion engines. A higher percentage downsized engine will produce less CO2. By extension, a higher boost level is required to generate high engine torque performance. The transient load step of a higher boost system at low RPM is currently an issue for conventional boosting. Aeristech has developed an electric supercharger to be matched with a conventional turbocharger to create a new type of two stage boosting system and a simpler downsized gasoline engine usable in mainstream vehicle segments. Whereas most electric pressure charging devices are capable of transient output to alleviate turbo lag. The electric supercharger is capable of steady-state air delivery. This makes the electric supercharger a dual-function device, alleviating turbo lag and also supplementing the compressor map of the turbocharger or main boost device.

Today the light-duty commercial market is dominated by internal combustion engine powered vehicles, primarily diesel-powered delivery vans, which contribute to urban air quality issues. Global concerns regarding climate change have prompted zero emission vehicles to be mandatory in many markets as soon as 2035. For the light-duty commercial vehicle sector there is significant interest in pure electric vehicles. However, for some markets, or usage cases, electric vehicles may not be the best solution due to practical limitations of battery energy storage capacity or recharging times. For such applications there is growing interest in hydrogen fuel cells as a zero emissions alternative. Bramble Energy’s patented printed circuit board (PCB) fuel cell technology (PCBFC™) enables the use of cost-effective production methods and materials from the PCB industry to reduce the cost and complexity of manufacturing hydrogen fuel cell stacks.

The work examined the practicality of converting a modern production 6 cylinder 7.7 litre heavy-duty diesel engine for flex dual-fuel operation with ammonia as the main fuel. A small amount of diesel fuel (pilot) was used as an ignition source. Ammonia was injected into the intake ports during the intake stroke, while the original direct fuel injection equipment was retained and used for pilot diesel injection. A bespoke engine control unit was used to control the injection of both fuels and all other engine parameters. The aim was to provide a cost-effective retrofitting technology for existing heavy-duty engines, to enable eco-friendly operation with minimal carbon emissions. The tests were carried out at a baseline speed of 600 rpm for the load range of the engine (10-90%), with minimum pilot diesel quantity and as high as 90% substitution ratio of ammonia for diesel fuel.

Gasoline engine downsizing is already established as a technology for reducing vehicle CO2 emissions. Further benefits are possible through more aggressive downsizing, however, the tradeoff between the CO2 reduction achieved and vehicle drivability limits the level of engine downsizing currently adopted by vehicle manufacturers. This paper will present the latest results achieved from a very heavily downsized engine, and resulting demonstrator vehicle, featuring eSupercharging in combination with a conventional turbocharger. The original 1.2 litre, 3-cylinder, MAHLE downsizing engine has been re-configured to enable a specific power output in excess of 160 kW/litre. Of key importance is a cost effective, efficient and flexible boosting system.

Significant reductions in vehicle carbon dioxide (CO2) emissions are required to meet fleet targets and this is increasing the interest in new combustion concepts for internal combustion engines. There is also an increased focus on the use of renewable fuels to reduce environmental impact. This study focusses on the use of methanol as an internal combustion engine fuel. Methanol is a liquid fuel that is readily produced from waste bio-matter, as well as synthetically using renewable energy, and is proposed as a primary energy vector in hard-to-decarbonise sectors, such as Marine, but could be equally applicable to road transportation. In this study, the MAHLE Di3 engine, which is a highly boosted 3-cylinder gasoline direct injection engine capable of operating at over 30 bar BMEP, has been modified to include MAHLE Jet Ignition technology, in both passive and active configurations, as well as utilising a very high compression ratio to maximise thermal efficiency.

This paper investigates the energy efficiency and emissions benefits possible with connected and autonomous vehicles (CAVs). Such benefits could be instrumental in decarbonising the transport sector. The impact of CAV technology on operation, usage and specification of vehicles for optimised energy efficiency is considered. Energy consumption reductions of 55% – 66% are identified for a fully autonomous road transport system versus the present. 46% is possible for a CAV on today’s roads. Smoothing effects and reduced stoppage in the drive cycle achieve a 31% reduction in travel time if speed limits are not reduced. CAV powertrain optimised for different scenarios requires just 10 kW – 40 kW maximum power whilst the vehicle mass is reduced by up to 40% relative to current cars. Urban-optimised powertrain, with only 10 kW – 15 kW maximum power, allows energy consumption reductions of over 71%.

The main focus nowadays for the development of future vehicle powertrain systems is the improvement in fuel efficiency alongside the reduction of pollutant emissions and greenhouse gasses, most notably carbon dioxide. The automotive community is already engaged in seeking solutions to these issues, however, the ideal solution, namely zero emission vehicle is still regarded as being a long way from fruition for the mass market. In the meantime steps are being taken, in terms of engineering development, towards improved fuel efficiency and sustainability of relatively conventionally powered vehicles. One approach to the decarbonization of road vehicles is to supplement existing fossil fuels with sustainable biofuels.

Ammonia (NH3) is emerging as a potential fuel for longer range decarbonised heavy transport, predominantly due to favourable characteristics as an effective hydrogen carrier. This is despite generally unfavourable combustion and toxicity attributes, restricting end use to applications where robust health and safety protocols can always be upheld. In the currently reported work, a spark ignited thermodynamic single cylinder research engine was upgraded to include gaseous ammonia and hydrogen port injection fueling, with the aim of understanding maximum viable ammonia substitution ratios across the speed-load operating map. The work was conducted under stoichiometric conditions with the spark timing re-optimised for maximum brake torque at all stable logged sites. The experiments included industry standard measurements of combustion, performance and engine-out emissions.