Search Results

The present investigation details an experimental procedure for frontal impact responses of a generic steel front bumper crush can (FBCC) assembly subjected to a rigid full and 40% offset impact. There is a paucity of studies focusing on component level tests with FBCCs, and of those, speeds carried out are of slower velocities. Predominant studies in literature pertain to full vehicle testing. Component level studies have importance as vehicles aim to decrease weight. As materials, such as carbon fiber or aluminum, are applied to vehicle structures, computer aided models are required to evaluate performance. A novel component level test procedure is valuable to aid in CAE correlation. All the tests were conducted using a sled-on-sled testing method. Several high-speed cameras, an IR (Infrared) thermal camera, and a number of accelerometers were utilized to study impact performance of the FBCC samples.

The short NiTi fiber-reinforced NiTi/Al6061-SiC composite was recently developed through the U.S. Army SBIR Phase-II program [1]. The objectives of this project are to use short NiTi fiber reinforcement to induce compressive stress through shape memory effect, to use silicon carbide (SiC) particulate reinforcement to enhance the mechanical properties of the aluminum matrix, to gain fundamental knowledge of short NiTi fiber-reinforced aluminum matrix composite, and eventually to improve fatigue resistance, impact damage tolerance and fracture toughness of the composite. The fatigue life, damage and fracture behavior of TiNi/Al6061-SiC, TiNi/Al6061, Al6061-SiC composites as well as monolithic Al6061 alloy were investigated under fully reversed cyclic loading. It was found that fatigue life of NiTi/Al6061-SiC composite, in term of the cycles, increased by two orders of magnitude, compared to monolithic Al6061 alloy

A composite of an aluminum matrix reinforced by short TiNi shape memory alloy (SMA) fibers was fabricated. The processing and thermomechanical behaviors of the composite TiNi/Al6061 were investigated experimentally and analytically. Optimal hot-pressing conditions of TiNi/Al6061 processing were identified. The shape memory effect (SME) was activated by prestraining the composite at the temperature between Ms and As, followed by heating up to Af. SME on mechanical properties, such as microhardness, yield stresses of the composite, were investigated. A computational model for the strengthening mechanism of the short fiber metal matrix composite was utilized to analyze SME on yield stress of the composite. Yield stress of the composite as a function of prestrain was predicted numerically and verified experimentally.

The Isodamp damping material (also known as Navy Damp) used in the ribs of current crash test dummies provides human-like damping to the thorax under impact. However, the range of temperature over which it can be used is very small. A new rib design using laminates of steel, fiberglass, and commercially available viscoelastic material has been constructed. Load-deflection response and hysteresis of the laminated ribs were compared with corresponding conventional ribs fabricated from steel and Isodamp. Impact tests were conducted on laminated and conventional ribs at 18.5° C, 22.2° C and 26.6° C. Results indicate that the response of the laminated ribs is essentially the same as that of the ribs with Isodamp at 22.2° C, which is the operating temperature of the conventional ribs. The variation in the impact response of the newly developed laminated ribs in the temperature range of 18.5° C to 26.6° C was less than 10%.

Light-weight adhesively bonded aluminum hat sections under axial compression can be used for energy absorption as a crash component in the vehicle. In order to obtain a comprehensive evaluation on safety and performance of this type of structure, the roles of adhesives as well as the aluminum adherend were investigated, and it was necessary to establish an appropriate FEA model which can be used for structural failure prediction and energy absorption response. It was found that the global behavior of short length adhesively bonded hat sections under axial compression is primarily governed by large plastic buckling deformation, and that the main contribution of the adhesive is to present separation of the flanges and corresponding reductions of effective flange thickness.

The automobile industry is seeing an increased need for the application of plastics and their derivatives in various forms such as fiber reinforced plastics, in the design and manufacture of various automotive structural components, to reduce weight, cost and improve fuel efficiency. A lot of effort is being directed at the development of structural plastics, to meet specific automotive requirements such as stiffness, safety, strength, durability and environmental standards and recyclability. Fiber reinforced plastics being viscoelastic in behavior, are susceptible to the rate of loading or the strain rate, especially at high temperature conditions. Bonded sections made up of fiber reinforced plastics therefore require the understanding of their mechanical behavior at different strain rates, such as low rate loading (to simulate quasi-static loading) and high strain rate loading (to simulate impact type loading).

Low cost and solid lubricant containing plasma spray coated cylinder liners have been investigated for their frictional performance under simulated engine conditions. A bench testing system which has high stroke and large contact width has been used to obtain friction data for plasma spray coated cylinder liners. Results are compared with conventional cast-iron samples. Experimental data has been developed as friction coefficient / crank angle degree diagrams. The effects of speed and temperature have been investigated. Plasma spray coated cylinder liners showed lower friction and higher tendency to develop hydrodynamic lubrication compared to conventional cast-iron bores.