Search Results

Real gas effects are studied during the compression stroke of a diesel engine. Several different real gas models are compared to the ideal gas law and to the experimental pressure history. Comparisons are done with both 1-D and CFD simulations, and reasons and answers are found out for the observed differences between simulations and experimental data. The engine compression ratio was measured for accurate model predictions. In addition, a 300bar extreme pressure case is also analyzed with the real gas model since an engine capable for this performance level is currently being built at the Aalto University School of Science and Technology. Real gas effects are even more important in these extreme conditions than in normal operating pressures. Finally, it is shown that the predicted pressure history during an engine compression stroke by a real gas model is more accurately predicted than by the ideal gas law.

Knocking combustion is a major obstacle towards engine downsizing and boosting—popular techniques towards meeting the increasingly stringent emission standards of SI engines. The commercially available gasoline is a mixture of many chemical compounds like paraffins, isoparaffins, olefins and aromatics⁠. Therefore, the modeling of its combustion process is a difficult task. Additionally, the blends of certain compounds exhibit non-linear behavior in comparison to the pure components in terms of knock resistance. These facts require further analysis from the perspective of combustion chemistry. The present work analyses the effects of blending ethanol to FACE-C gasoline. A range of pressures, temperatures, and equivalence ratios has been considered for this purpose. The open source softwares Cantera version 2.4.0 and OpenSMOKE++ Suite have been used for the simulations.

Gasoline blending is known to be complicated, because individual gasoline fractions with different octane numbers, Research Octane Number (RON) or Motor Octane Number (MON) do not always blend linearly. Instead, they may blend non-linearly, in a synergistic or antagonistic manner. Even though RON and MON are regulated properties, linear and non-linear octane blending is not a broadly understood topic. The target in the developing process of a modern SI engine is to have 100% combustion efficiency which would lead to the reduction of hydrocarbon and carbon monoxide emissions. Therefore, the properties of gasoline, especially RON and MON, need to be optimized to ensure proper ignition in the engine and prevent harmful autoignition reactions. There are hundreds of hydrocarbons in gasoline which have different octane numbers (ON). The explanations for these variations are the structural differences in hydrocarbon molecules that influence on their reactivity.

The engine fueled with methane/diesel is a promising and highly attractive operation mode due to its high performance-to-cost ratio and clean-burning qualities. However, the combustion process and chemical reactions in dual fuel combustion are highly complex, involving short transient pilot-fuel injection into the premixed gaseous fuel charge, autoignition, and combustion mode transition into premixed flame propagation. The motivation of the current investigation is to gain an insight into the combustion dynamics in dual fuel combustion engine based on chemical radicals and thermal radiation. The chemiluminescence (CL) and natural luminosity (NL) are expected to provide specific characteristics in combustion control and monitoring. To visualize the highly unsteady combustion process in terms of OH*, CH2O* radicals and natural luminous emissions, the band pass filters with 308 nm, 330 nm combined with an image doubler are employed to visualize the OH* and CH2O* CL simultaneously.

Over the past few years, the growing concerns about global warming and efforts to reduce engine-out emissions have made the dual-fuel (DF) engines more popular in marine and power industries. The use of natural gas as an alternative fuel in DF engines has both the environmental and economic advantages over the conventional diesel combustion. However, the misfire phenomenon at lean conditions limits the operating range of DF combustion and causes emissions of unburned hydrocarbon (UHC) and unburned methane (methane-slip) in the environment. The greenhouse effect of methane is considered 28 times greater than CO2 over a 100-year perspective, which raises concerns for the governments and marine engine manufacturers. In efforts to reduce the UHC and methane-slip from DF engines, this study discusses ethane enrichment of diesel-methane DF combustion in a full-metal single-cylinder research engine under lean condition (λGFB = ~2.0) while keeping the total-fuel energy rather constant.

The direct injection (DI) natural gas engine is considered as one of the promising technologies to achieve the continuing goals of the higher efficiency and reduced emissions for internal combustion engines. Shock wave phenomena can easily occur near the nozzle exit when high pressure gaseous fuel is injected directly into the engine cylinder. In the present study, high pressure gas issuing from a prototype gas injector was experimentally studied using planar laser-induced fluorescence (PLIF) technique. Acetone was selected as a fuel tracer. The effects of injection pressures on the flow structure and turbulent mixing were investigated based on a series of high resolution images. The jet macroscopic structures, such as jet penetration, cone angle and jet volume, are analyzed under different injection pressures. Results show that barrel shock waves can significantly influence the jet flow structure and turbulent mixing.

As CO2 emissions from traffic must be reduced and fossil-based traffic fuels need to phase out, bio-based traffic fuels alone cannot meet the future demand due to their restricted availability. Another way to support fossil phase-out is to include synthetic fuels that are produced from circular carbon sources with renewable energy. Several different fuel types have been proposed, while, methanol only requires little processing from raw materials and could be used directly or as a drop-in fuel for some of the current engine fleet. CO2 emissions arising from fuel production are significantly reduced for synthetic renewable methanol compared to the production of fossil gasoline. Methanol has numerous advantages over the currently used fossil fuels with high RON and flame speed in spark-ignition engines as well as high efficiency and low emissions in combustion ignition engines.

The flow through the valves of an engine cylinder head is very complex in nature due to very high gas velocities and strong flow separation. However, it is also the typical situation in almost every engine related flow. In order to gain better understanding of the flow features after the cylinder head, and to gain knowledge of the performance level that can be expected from CFD analysis, flow field measurements and computations were made in an engine rig. Particle image velocimetry (PIV) and paddle wheel measurements have been conducted in a static heavy-duty diesel engine rig to characterize the flow features with different valve lifts and pressure differences. These measurements were compared with CFD predictions of the same engine. The simulations were done with the standard k-ε turbulence model and with the RNG turbulence model using the Star-CD flow solver.

The current study was focused on flow field measurements of diesel sprays. The global fuel spray characteristics, such as spray penetration, have also been measured. Particle Image Velocimetry (PIV) was utilized for flow field measurements and the global spray characteristics were recorded with high-speed back light photographing. The flow field was scanned to get an idea of the compatibility of PIV technique applied to dense and high velocity sprays. It is well proven that the PIV technique can be utilized at areas of low number density of droplets, but the center of the spray is way beyond the ideal PIV measurement conditions. The depth at which accurate flow field information can be gathered was paid attention to.

The study aims at providing more accurate initial conditions for turbulence prior to combustion with the help of a four valve, large bore diesel engine CFD model. Combustion simulations are typically done with a sector mesh and initial turbulence in these simulations is usually taken from relatively inaccurate correlations. This study also aims at developing a more accurate initial turbulence correlation for combustion simulations. A one-dimensional model was first used to provide boundary conditions as well as the initial flow conditions at the beginning of the simulation. Steady state and transient boundary conditions were studied. Also, the standard κ - ε and RNG/κ - ε turbulence models were compared. From the averaged values of turbulence kinetic energy and its dissipation rate over the cylinder volume, a re-tuned correlation for defining the initial turbulent conditions at bottom dead center (BDC) prior to the compression stroke is proposed.

The development of new high power diesel engines is continually going for increased mean effective pressures and consequently increased thermal loads on combustion chamber walls close to the limits of endurance. Therefore accurate CFD simulation of conjugate heat transfer on the walls becomes a very important part of the development. In this study the heat transfer and temperature on piston surface was studied using conjugate heat transfer model along with a variety of near wall treatments for turbulence. New wall functions that account for variable density were implemented and tested against standard wall functions and against the hybrid near wall treatment readily available in a CFD software Star-CD.

Renewable diesel-type fuels and their compatibility with a single-cylinder medium-speed research diesel engine were studied. The report consists of a literature study on the fuels, introduction of the simulation model designed and simulations made, and of the results and summary sections. The fuels studied were traditional biodiesel (fatty acid methyl ester, FAME), hydrotreated vegetable oil (HVO), Fischer-Tropsch (FT) diesel fuels and dimethyl ether (DME). According to the simulations, the behaviors of different renewable diesel fuels in the fuel injection system are quite similar to one another, with the greatest deviations found with DME. The main differences in the physical properties are fuel densities and viscosities and especially with DME compressibility, which have some predictable effect. The chemical properties of the fuels are more critical for a common rail fuel injection system.

The objective of this study is to achieve high reduction of NOx emissions in a medium-speed single-cylinder research engine. The main feature of this research engine is that the gas exchange valve timing is completely adjustable with electro-hydraulic actuators. The study is carried out at high engine load and using a very advanced Miller valve timing. Since the engine has no turbocharger, but a separate charge air system, 1-D simulations are carried out to find the engine setup, which would be close to the operating points of a real engine. The obtained NOx reduction is over 40% with no penalty in fuel consumption.

A new variable density / physical property wall function formalism has been developed. The new formalism is designed to extend the validity range of wall functions to cover both the low- and high-Reynolds-number domains so that the restrictions on the non-dimensional near-wall mesh resolution can be avoided. The new formalism also accounts for the temperature gradient induced variations of density, viscosity, heat conductivity and specific heat capacity. The new wall function formalism is constructed in conjunction with a modified low-Reynolds-number turbulence model in order to avoid the conflicting requirements of low- and high-Reynolds-number models on the near wall mesh resolution. The new formulation is validated with test simulations of strongly heated air flows in circular tube against measurements and Direct Numerical Simulation (DNS) results.

Experimental spray tip penetrations obtained from a large-bore medium-speed optical diesel engine were compared to CFD simulations. The optical spray results are unique as they are obtained from a running large-bore (200mm) diesel engine. The experimental spray tip penetration measurements were obtained during the early spray development period when the spray evaporation had not yet reached the quasi steady-state phase. The CFD simulations were conducted in both static chamber environment and in engine conditions. The fuel injection boundary conditions were obtained from 1-D simulations. Within the error margins associated with the experimental and computational data, relatively good accuracy was obtained between measured and simulated spray tip penetration. It was also observed that it is very important to have accurate fuel injection mass flow rate data. This was observed after a sensitivity analysis was made for the injection duration and fuel mass quantity.

Two different medium-speed diesel engine cylinder head designs have been studied. The focus of the study has been the effect of intake channel design in the in-cylinder flow. The study has been carried out by CFD. The first cylinder head is a standard Wärtsilä 20 cylinder head and the second one is a specially designed head for a single cylinder research engine, called Extreme Value Engine (EVE). The CFD boundary conditions have been simulated by the help of a 1-d simulation code. In the full load cases the maximum cylinder pressure was 300 bar. Simulations have been done at lower load level too. One simulation with the new cylinder head was carried out with one intake valve closed in order to get an idea of the swirl to be generated by this approach. In the study the in-cylinder flow field, the cylinder charge and turbulence kinetic energy have been examined.

Hydrotreated vegetable oil (HVO) is a high-cetane number alternative fuel with the potential of drastic emissions reductions in high-pressure diesel engines. In this study the behavior of HVO sprays is investigated computationally and compared with conventional diesel fuel sprays. The simulations are performed with a modified version of the C++ open source code OpenFOAM using Reynolds-averaged conservation equations for mass, species, momentum and energy. The turbulence has been modeled with a modified version of the RNG k-ε model. In particular, the turbulence interaction between the droplets and the gas has been accounted for by introducing appropriate source terms in the turbulence model equations. The spray simulations reflect the setup of the constant-volume combustion cell from which the experimental data were obtained.

Three-dimensional diesel engine combustion simulations with single-step chemistry have been compared with two-step and three-step chemistry by means of the Laminar and Turbulent Characteristic Time Combustion model using the Star-CD program. The second reaction describes the oxidation of CO and the third reaction describes the combustion of H2. The comparisons have been performed for two heavy-duty diesel engines. The two-step chemistry was investigated for a purely kinetically controlled, for a mixing limited and for a combination of kinetically and mixing limited oxidation. For the latter case, two different descriptions of the laminar reaction rates were also tested. The best agreement with the experimental cylinder pressure has been achieved with the three-step mechanism but the differences with respect to the two-step and single-step reactions were small.

A modified version of the Laminar and Turbulent Characteristic Time combustion model and the Hiroyasu-Magnussen soot model have been implemented in the flow solver Star-CD. Combustion simulations of three DI diesel engines, utilizing the standard k-ε turbulence model and a modified version of the RNG k-ε turbulence model, have been performed and evaluated with respect to combustion performance and emissions. Adjustments of the turbulent characteristic combustion time coefficient, which were necessary to match the experimental cylinder peak pressures of the different engines, have been justified in terms of non-equilibrium turbulence considerations. The results confirm the existence of a correlation between the integral length scale and the turbulent time scale. This correlation can be used to predict the combustion time scale in different engines.

The one-equation subgrid scale model for the Large Eddy Simulation (LES) turbulence model has been compared to the popular k-ε RNG turbulence model in very different sized direct injection diesel engines. The cylinder diameters of these engines range between 111 and 200 mm. This has been an initial attempt to study the effect of LES in diesel engines without any modification to the combustion model being used in its Reynolds-averaged Navier-Stokes (RANS) form. Despite some deficiencies in the current LES model being used, it already gave much more structured flow field with approximately the same kind of accuracy in the cylinder pressure predictions than the k-ε RNG turbulence model.