Search Results

Upcoming legislation towards zero carbon emission is pushing the electric vehicle as the main solution to achieve this goal. However, electric vehicles still require further battery development to meet customer’s requirements as fast charge and high energy density. Both demands come with the cost of higher heat dissipation as lithium transport and chemical reaction inside the battery need to be performed faster, increasing the joule effect inside the battery. Due to its working principle, which guarantees an adiabatic environment, an accelerating rate calorimeter is used to study thermal phenomena in batteries like a thermal runaway. However, this equipment is not prepared to work with optical access, which helps to study and to comprehend battery surface distribution and other thermal aspects. This paper aims to show a methodology to correct temperature measurement when using a thermographic camera and optical access of sapphire in an accelerating rate calorimeter.

The reduction of carbon footprint of compression ignition engines for road transport makes it necessary to search for clean fuels alternative to diesel and to evaluate them under engine conditions. For this reason, in this paper, the combustion behaviour of different blends of synthetic fuels has been analyzed in an optical single cylinder engine of Medium Duty size (0,8 liters per cylinder) by means of optical techniques. The aim is to evaluate the effect of synthetic fuels, both partly or completely fossil diesel, in terms of combustion behaviours and soot formation. Therefore, different blends of oxymethylene dimethyl ether (OMEX) with diesel and neat hydrotreated vegetable oil (HVO) were studied. A conventional common rail injection system and a single injection strategy was used. In addition, special care was taken to ensure that conditions inside the engine cylinder at the injection start were as close as possible to the conditions used in previous studies.

A comparison of the flame structure for two different fuels, dodecane and oxymethylene dimethyl ether (OMEX), has been performed under condition of Spray A of the Engine Combustion Network (ECN). The experiments were carried out in a constant pressure vessel with wide optical access, at high pressure and temperature and controlled oxygen concentration. The flame structure analysis has been performed by measuring the formaldehyde and OH radical distributions using planar Laser-Induced Fluorescence (PLIF) techniques. To complement the analysis, this information was combined with that obtained with high-speed imaging of OH* chemiluminescence radiation in the UV. Formaldehyde molecules are excited with the 355-nm radiation from the third harmonic of a Nd:YAG laser, whilst OH is excited with a wavelength of 281.00-nm from a dye laser.

With demanding emissions legislations and the need for higher efficiency, new technologies for compression ignition engines are in development. One of them relies on reducing the heat losses of the engine during the combustion process as well as to devise injection strategies that reduce soot formation. Therefore, it is necessary a better comprehension about the turbulent kinetic energy (TKE) distribution inside the cylinder and how it is affected by the interaction between air flow motion and fuel spray. Furthermore, new diesel engines are characterized by massive decrease of NOx emissions. Therefore, considering the well-known NOx-soot trade-off, it is necessary a better comprehension and overall quantification of soot formation and how the different injection strategies can impact it.

It is known that in-cylinder airflow structures during intake and compression strokes deeply affects the combustion process in compression ignition (CI) engines. This work presents a methodology for the analysis of the swirling structures by means of the CFD proprietary code Converge 2.3. The methodology is based on the CFD modelling and the comparison of results with in-cylinder velocity fields measured by particle image velocimetry (PIV). Furthermore, the analysis is extended to the accuracy evaluation of other methods available to define the flow in the cylinder of internal combustion engines, such as experiments in steady flow rigs. These methods, in junction with simple phenomenological models, have been traditionally used to determine some of the fundamental variables that define the in-cylinder flow in ICE engines. The CFD analysis is focused in the flow structures around top dead centre (TDC) at the end of the compression stroke.

The Engine Combustion Network (ECN) is a coordinate effort from research partners from all over the world which aims at creating a large experimental database to validate CFD calculations. Two injectors from ECN, namely Spray C and D, have been compared in a constant pressure flow vessel, which enables a field of view of more than 100 mm. Both nozzles have been designed with similar flow metrics, with Spray D having a convergent hole shape and Spray C a cylindrical one, the latter being therefore more prone to cavitation. Although the focus of the study is on reacting conditions, some inert cases have also been measured. High speed schlieren imaging, OH* chemiluminescence visualization and head-on broadband luminosity have been used as combustion diagnostics to evaluate ignition delay, lift off length and reacting tip penetration. Parametric variations include ambient temperature, oxygen content and injection pressure variations.

Ever decreasing permitted emission levels and the necessity of more efficient engines demand a better understanding of in-cylinder phenomena. In swirl-supported compression ignition (CI) engines, mean in-cylinder flow structures formed during the intake stroke deeply influence mixture preparation prior to combustion, heat transfer and pollutant oxidation all of which could potentially improve engine performance. Therefore, the ability to characterize these mean flow structures is relevant for achieving performance improvements. CI mean flow structure is mainly described by a precessing vortex. The location of the vortex center is key for the characterization of the flow structure. Consequently, this work aims at evaluating algorithms that allow for the location of the vortex center both, in ensemble-averaged velocity fields and in instantaneous velocity fields.

In the past few years’ various studies have shown how the application of a highly premixed dual fuel combustion for CI engines leads a strong reduction for both pollutant emissions and fuel consumption. In particular a drastic soot and NOx reduction were achieved. In spite of the most common strategy for dual fueling has been represented by using two different injection systems, various authors are considering the advantages of using a single injection system to directly inject blends in the chamber. In this scenario, a characterization of the behavior of such dual-fuel blend spray became necessary, both in terms of inert and reactive ambient conditions. In this work, a light extinction imaging (LEI) has been performed in order to obtain two-dimensional soot distribution information within a spray flame of different diesel/gasoline commercial fuel blends. All the measurements were conducted in an optically accessible two-stroke engine equipped with a single-hole injector.

Visualization of single-hole nozzles into quiescent ambient has been used extensively in the literature to characterize spray mixing and combustion. However in-cylinder flow may have some meaningful impact on the spray evolution. In the present work, visualization of direct diesel injection spray under both non-reacting and reacting operating conditions was conducted in an optically accessible two-stroke engine equipped with a single-hole injector. Two different high-speed imaging techniques, Schlieren and UV-Light Absorption, were applied here to quantify vapor penetration for non-reacting spray. Meanwhile, Mie-scattering was used to measure the liquid length. As for reacting conditions, Schlieren and OH* chemiluminescence were simultaneously applied to obtain the spray tip penetration and flame lift-off length under the same TDC density and temperature. Additionally, PIV was used to characterize in-cylinder flow motion.

Recent studies have shown that the use of highly premixed dual fuel combustion reduces pollutant emissions and fuel consumption in CI engines. The most common strategy for dual fueling is to use two injection systems. Port fuel injection for low reactivity fuel and direct injection for high reactivity fuel. This strategy implies some severe shortcomings for its real implementation in passenger cars such as the use of two fuel tanks. In this sense, the use of a single injection system for dual fueling could solve this drawback trying to maintain pollutant and efficiency benefits. Nonetheless, when single injection system is used, the spray characteristics become an essential issue. In this work the fundamental characteristics of dual-fuel sprays with a single injection system under non-evaporating engine-like conditions are presented.

A radiation-based 2-color method (2C) and light extinction imaging (LEI) have been performed simultaneously to obtain two-dimensional soot distribution information within a diesel spray flame. All the measurements were conducted in an optically accessible two-stroke engine equipped with a single-hole injector. The fuel used here is a blend of 30% Decane and 70% Hexadecane (in mass). According to previous research, operating conditions with three different flame soot amounts were investigated. The main purpose of this work is to evaluate the two soot diagnostics techniques, after proper conversion of soot-related values from both methods. All the KL extinction values are lower than the saturation limit. As expected, both techniques show sensitivity with the parametric variation. The soot amount increases with higher ambient gas temperature and lower injection pressure. However, the LEI technique presents more sensitivity to the soot quantity.

On actual gasoline turbocharged engines it is common to use a compressor by-pass valve in order to solve the compressor surge problem when the throttle pedal position is released and closes rapidly. The paper deals with a methodology based on experiments to measure the discharge coefficient of an integrated compressor by-pass valve, to understand the possible difference between the steady flow test bench and turbocharger test bench discharge coefficient measurements. To determine if there is some compressor outlet flow field influence due to compressor blades rotation that could modify the discharge coefficient measurement, compared to the steady flow test bench measurements, a fully instrumented turbocharger was used to measure the difference between steady flow test bench and turbocharger test bench discharge coefficients results. Effects of different boundary conditions on turbocharger test bench tests and how they affect the discharge coefficient measurement are also presented.

Major accuracy for prediction tools like CFD codes require precise experimental validation. The ultraviolet and visible light absorption and scattering (UV-VIS LAS) is proposed for characterizing air-fuel mixture formation. UV-VIS LAS technique is employed to quantitatively determine spatial concentration distribution of vapor fuel, in combination with simultaneous liquid length and spray penetration measurements by means of Mie-scattering and Schlieren. Decane, Hexadecane and a 50/50 of both fuels have been chosen for this study, to evaluate mixing formation under Diesel conditions. Work has been performed at an optical engine under non-reacting atmosphere, with ambient pressures and temperatures up to 7.3 MPa and 900 K. Fuel optical properties for the two paraffines under engine conditions have been analyzed, and fuel concentration distribution has been obtained for pure fuels.

Schlieren/shadowgraphy has been adopted in the combustion research as a standard technique for tip penetration analysis of sprays under diesel-like engine conditions. When dealing with schlieren images of reacting sprays, the combustion process and the subsequent light emission from the soot within the flame have revealed both limitations as well as considerations that deserve further investigation. Seeking for answers to such concerns, the current work reports an experimental study with this imaging technique where, besides spatial filtering at the Fourier plane, both short exposure time and chromatic filtering were performed to improve the resulting schlieren image, as well as the reliability of the subsequent tip penetration measurement. The proposed methodology has reduced uncertainties caused by artificial pixel saturation (blooming).

Accurate simulation tools are needed for rapid and cost effective engine development in order to meet ever tighter pollutant regulations for future internal combustion engines. The formation of pollutants such as soot and NOx in Diesel engines is strongly influenced by local concentration of the reactants and local temperature in the combustion chamber. Therefore it is of great importance to model accurately the physics of the injection process, combustion and emission formation. It is common practice to approximate Diesel fuel as a single compound fuel for the simulation of the injection and combustion process. This is in many cases sufficient to predict the evolution of the in-cylinder pressure and heat release in the combustion chamber. The prediction of soot and NOx formation depends however on locally component resolved quantities related to the fuel liquid and gas phase as well as local temperature.

In the wake of the Turbulent Nonpremixed Flames group (TNF) for atmospheric pressure flames, an open group of laboratories belonging to the Engine Combustion Network (ECN) agreed on a list of boundary conditions -called “Spray A”- to study the free diesel spray under steady-state conditions. Such conditions are relevant of a diesel engine operating at low temperature combustion conditions with moderate EGR, small nozzle and high injection pressure. The objective of this program is to accelerate the understanding of diesel flames, by applying each laboratory's knowledge and skills to a specific set of boundary conditions, in order to give an extensive and reliable experimental database to help spray modeling. In the present work, “Spray A” operating condition has been achieved in a constant pressure, continuous flow vessel. Schlieren high-speed imaging has been conducted to measure the spray penetration under evaporative conditions.

The relationship between ignition, lift-off length and soot formation was investigated for a collection of fuels in an optically-accessible modified 2-stroke engine under a set of typical quasi-steady state Diesel DI conditions. Five fuels including biodiesel blends and Fischer-Tropsch fuels have been selected for their potential to substitute conventional diesel with no major modifications on the engine hardware, and were previously characterized under ambient pressure following ASTM standards. Fuels were injected into a large volume through a single-hole nozzle at three levels of injection pressure, by sweeping ambient temperatures at constant density, and ambient densities at constant temperature. The 8 ms single-shot injections were long enough to reach the stabilization of a free diffusion flame. The OH-chemiluminescence was imaged and lift-off length was measured via image post-processing.

The present work relates to the investigation of the basic oxidation characteristics of iron and aluminium nanoparticles as well as the feasibility of their combustion under both Internal Combustion Engine (ICE)-like and real engine conditions. Based on a series of proof-of-concept experiments, combustion was found to be feasible taking place in a controllable way and bearing similarities to the respective case of conventional fuels. These studies were complimented by relevant in-situ and ex-situ/post-analysis, in order to elaborate the fundamental phenomena occurring during combustion as well as the extent and ‘quality’ of the process. The oxidation mechanisms of the two metallic fuels appear different and -as expected- the energy release during combustion of aluminium is significantly higher than that released in the case of iron.

A study was conducted to investigate the evolution of liquid phase penetration of evaporating sprays under engine-like conditions, with diesel and biodiesel fuel blends. This study has been performed in a facility based on a single cylinder two-stroke direct injection Diesel engine operating at low rotational speed which provides a quiescent thermodynamic environment around TDC, when fuel is injected, realistic for current D.I. Diesel engines. Due to the absence of inlet or exhaust valves, very easy optical access to the combustion chamber can be provided through the cylinder head. Pure nitrogen is supplied to the engine as intake gas, in order to avoid combustion. The injection event is carried out by an electronically controlled common rail system. The injector is equipped with real 8-hole nozzles, with a hole diameter of 0.115 mm. Injection pressures in this study ranged between 30 and 160 MPa and different in-cylinder peak pressure and temperature values were considered.

The aim of this paper is to analyse the swirling flow in the cylinder of DI Diesel engines. Both steady state flow rig and CFD calculation techniques on three Diesel engines at different configurations have been used to carry out this study. On one hand, results obtained by means of steady state flow rig measurements with torque-meter are presented. On the other hand, the intake and compression strokes are calculated using a CFD commercial code on real geometries of three engines at different working conditions. The experimental and the CFD methods are compared in terms of Swirl Number and Flow Coefficient, so some correlations are achieved at BDC and TDC and a general equation -valid for different geometries- has been obtained to estimate the Swirl Number in the cylinder of DI Diesel engines at TDC directly from the data -Mean Swirl Number- provided by the experimental tests.