Search Results

Tire manufacturers need to perform various types of testing to determine tire performance under representative vehicle load conditions. However, test results are influenced by a number of external variables other than tire construction. Vehicle load distribution and suspension properties are some of those external variables which can have a significant effect on tire wear rate and durability. Therefore, in order to measure real world tire performance in a controlled and repeatable manner, a representative vehicle and associated tire load conditions are needed. Laboratory or indoor tire testing offers many advantages over vehicle fleet testing. It provides a well-defined test environment and repeatable results without influence from external factors. Indoor testing has been largely developed around the process of simulating tire wear performance on a specific reference vehicle, including its specific weight distribution, suspension characteristics, and alignment.

In response to the TREAD act of 2002, ASTM F09.30 Aged Tire Durability Task Group was formed with the objective of developing a scientifically valid, short duration aged durability test which correlates to field behavior. The target end-of-test condition was belt edge separation (or related damage). One strategy, driven by that objective, has been a steady state design of experiment investigating aging temperature and duration as well as roadwheel speed, pressure and deflection. The rationale behind investigating a steady state test and selecting these parameters and methodology for setting their initial values is reviewed.

In response to the TREAD act of 2002, ASTM F09.30 Aged Tire Durability Task Group was formed with the objective of developing a scientifically valid, short duration, laboratory aged tire durability test which correlates to field behavior. The target end-of-test condition was belt edge separation (or related damage). Two strategies have been investigated, aged stepped-up load and steady state DOE. Results of the two strategies are compared and contrasted and a test condition from the steady state DOE has been identified as the preferred direction for further validation.

In the work leading to the TREAD Act, some members of Congress expressed the need for some type of aging test on light vehicle tires. Since no industry-wide recommended practice existed, the ASTM F09.30 Aged Tire Durability task group was established in 2002 to develop a scientifically valid, short duration, laboratory aged tire durability test which correlates to in-service aging. The target end-of-test condition was belt edge separation (or related tire conditions). One strategy, driven by that objective, has been a Steady State DOE investigating aging temperature and duration, as well as, roadwheel speed, pressure and deflection. Testing was performed on three tire types, including two where relevant field aging data was publicly available from NHTSA studies. A region of interest, within the design space, was identified where target end-of-test conditions were possible and undesirable (non-target or non-representative of those seen in consumer use) were avoided.

In response to the TREAD act, ASTM F09.30 Aged Tire Durability Task Group was formed in 2002 with the objective of developing a scientifically valid, short duration, laboratory aged tire durability test which correlates to field behavior. The target end-of-test condition was belt edge separation (or related damage). One strategy, driven by that objective, has been investigation of an aged, stepped-up load test, modeled after the FMVSS 139 endurance test, but examining different velocities and step durations, plus oven aging durations. Testing was performed on two tire types where relevant field aging data was available from earlier NHTSA studies. Resulting end-of-test conditions were predominately non-representative of those seen in consumer use. These results have been associated with high tire temperatures, which in turn are linked with the high cyclic deflections caused by the specified load and pressure conditions.

Indoor or laboratory testing of tire tread wear offers many advantages over vehicle fleet testing. Advances in test equipment capabilities and the technologies for defining and simulating meaningful tire loading histories has made indoor tread wear testing a reality. Tire loading histories are influenced by vehicle characteristics, wear course and driving style, and tire stiffnesses. Methods for independently characterizing each of these are reviewed. A simulation technique, TS-Sim, is also described that combines specific vehicle, course and tire characterizations to create a tire load history. The vehicle characterization is critical to the process since both wear rate and various forms of uneven and irregular wear are strongly dependent on vehicle suspension/steering characteristics and on dynamic load transfer behavior. The characterization process involves mapping the vehicle over a practical range of acceleration, deceleration and cornering maneuvers.