Search Results

Two characteristics of terrain mobility are essential in designing an unmanned ground vehicle (UGV): (i) the ability of a vehicle to move through terrain of a given trafficability and (ii) the obstacle performance, i.e., the ability to avoid, interact with and overcome obstacles encountered on a preset route of a vehicle. More attention has been given to the vehicle geometry including selection of the angles of approach and departure, radii of longitudinal and lateral terrain mobility, and the steering system configuration. An essential effect is exhibited by the tire properties in their interaction with the support surface; this, in turn, affects traction properties of the wheel and, thus, vehicle terrain mobility. However, the influence of power distribution between the driving wheels together with vehicle steering system on the two above-listed characteristics of terrain mobility has not been considered in depth.

This paper starts with an analysis of design configurations of the drivelines with different power-dividing units (PDUs) of main dump truck manufacturing companies. As it follows from the analysis, improvements of articulated truck energy efficiency and reduction of fuel consumption by optimizing the power distribution to the drive wheels are still open issues. The problem is that a variety of operating and terrain conditions of dump trucks requires different wheel power distributions that cannot be provided by one set of PDUs employed in a truck. The central PDU in the transfer case was identified as the most important PDU among the five PDUs, which plays a crucial role in the power distribution between the front axle and the rear tandem of a 6×6 articulated dump truck. The paper formulates a constraint optimization problem to minimize the tire slippage power losses by optimizing the power distribution between the drive wheels.

In-wheel electric motors open up new prospects to radically enhance the mobility of autonomous electric vehicles with four or more driving wheels. The flexibility and agility of delivering torque individually to each wheel can allow significant mobility improvements, agile maneuvers, maintaining stability, and increased energy efficiency. However, the fact that individual wheels are not connected mechanically by a driveline system does not mean their drives do not impact each other. With individual torques, the wheels will have different longitudinal forces and tire slippages. Thus, the absence of driveline systems physically connecting the wheels requires new approaches to coordinate torque distribution. This paper solves two technical problems. First, a virtual driveline system (VDS) is proposed to emulate a mechanical driveline system virtually connecting the e-motor driveshafts, providing coordinated driving wheel torque management.

All-wheel drive (AWD) vehicle performance considerably depends not only on total power amount needed for the vehicle motion in the given road/off-road conditions but also on the total power distribution among the drive wheels. In turn, this distribution is largely determined by the driveline system and its mechanisms installed in power dividing units. They are interwheel, interaxle reduction gears, and transfer cases. The paper presents analytical methods to evaluate the energy and, accordingly, fuel efficiency of vehicles with any arbitrary number of the drive wheels. The methods are based on vehicle power balance equations analysis and give formulas that functionally link the wheel circumferential forces with slip coefficients and other forces acting onto an AWD vehicle. The proposed methods take into consideration operational modes of vehicles that are tractive mode, load transportation, or a combination of both.

All-wheel driveline systems with electronic torque control on each and all wheels, torque vectoring and torque management devices, hybrid electro-mechanical systems, and individual electro (hydraulic) motors in the wheels have been gaining a bigger interest in the industry for recent years. The majority of automotive applications are in vehicle stability control that is performed by controlling the vehicle yaw moment. Some devices also improve vehicle traction performance. The proposed paper develops a methodology that includes the key-principles in all-wheel driveline systems design and is based on the wheel power management as a broader analytical approach. The proposed principles relate to the optimization of power distributions to the drive wheels in both rectilinear and curvilinear vehicle motion. Inverse dynamics is the basis for the developed methodology.

An open-link locomotion module (OLLM) is an autonomous energy self-sufficient locomotion setup for designing ground wheeled vehicles of a given configuration that includes drive/driven and steered/non-steered wheels with individual suspension and brake systems. Off-road applications include both trucks and trailers. The paper concentrates on the module's electro-hydraulic suspension design and presents results of analytical and experimental studies of a trailer with four driven (no wheel torque applied) open-link locomotion modules. On highly non-even terrain, the suspension design provides the sprung mass with sufficient vibration protection at low level of normal oscillations, enhanced damping and stabilized angular movements. This is achieved by the introduction of two control loops: (i) a fast-acting loop to control the damping of the normal displacements; and (ii) a slow-acting control loop for varying the pressure and counter-pressure in the suspension system.

Brake-based traction control systems (TC), which utilize the brake of a spinning wheel of the drive axle, are widely used in passenger cars and light trucks, and recently were applied to all-wheel drive construction equipment. Such machines employ various types of interwheel drive systems (i.e., axle drives such as open differentials, limited slip differentials, etc.) to control torque split between the drive wheels and, thus, improve vehicle traction performance. As experimental research showed, the interaction between the traction control system and the axle drive can lead to unpredictable changes in vehicle performance. Lack of analytical work in this area motivated this study of the interaction and impact of the two systems on each other and the dynamics and performance of a drive axle.

Running abilities of an off-road, all-wheel drive vehicle depend considerably not only on total traction effort but also on its distribution among the drive wheels. This distribution is largely determined by mechanisms and systems installed in power dividing transmission units. These are interwheel differentials, interaxle reduction gears, and transfer cases. To control the wheel driving forces for obtaining the optimum vehicle properties, a more creative and efficient way to design wheel drive systems and to control vehicle running abilities is being proposed. Optimization criteria for the tractive and velocity properties, fuel consumption, turnability, and ride stability of a vehicle have been used for the mathematical optimization of the wheel driving forces. The vehicle is modeled in motion with taking into account the kinematic requirements.

Mass and geometric parameters of all-wheel drive off road vehicles, such as coordinates of the center of gravity and arrangement of the wheels, have been obtained to satisfy cross-country mobility profiles that reduce the dynamic normal loads on the running gear system. However, the influence of these parameters on tractive properties for basic cross-country mobility of vehicles receives less attention. The authors have developed a new method for determining mass and geometric parameters that provides optimal tractive properties for basic cross-country mobility of off-road vehicles. The methodology is realized using a mathematical model of a 6WD tractor on a deformable road surface. The mass and geometric parameters are achieved by optimizing the tractive efficiency function to provide the best transport efficiency on all running gears.

Normal and longitudinal dynamics of vehicles interrelates via the normal and longitudinal tire reactions. The normal reactions are supposed to be formed by characteristics of the suspension system and tires, and the longitudinal forces in the tire patches are produced by the driveline system by supplying torques to the drive wheels. Usually, the normal and longitudinal reactions, independently generated by the two vehicle systems, are considered to interrelate, but not to impact each other. An analytical study presented in this paper showed that the normal tire reactions are formed not only by the design of suspension but also by the longitudinal tire reactions (circumferential wheel forces), which follow from the wheel torques supplied by the driveline system. A 6×6 vehicle with A-type suspension systems at all three axles exhibits different normal tire reactions at the drive axles during motion even when the static weight distribution is equal.

Robotic technology has begun to play an essential role in ground automotive applications. Utility trucks are among the first responders in extreme climate and severe weather conditions, comprised of two systems: a mobile platform and an articulated robotic morphing arm. The conventional industrial manipulators are mounted on stationary bases, while a mobile manipulator is dynamically coupled on a mobile platform. Such trucks with morphing manipulator can increase the possibility of road accidents in many ways and, additionally, create dangerous situations on the roads, and off-road conditions, while moving, and performing tasks. Large boom equipped trucks for reaching elevated heights can become unstable due to drastic variation of the boom equipment moment of inertia causing the extreme weight re-distribution among the wheels. The morphing capabilities of the utility trucks need to be investigated together with the vehicle-road forces in order to hold the truck safe on the roads.

As proven, both friction in the gearing and movement of the contact point of the teeth in mesh along the pressure line generate vibrations of the axial components of the resultant force acting in a couple of mating straight bevel gears. The vibrations of the real forces in gearings cause an increased dynamic pressure on and, accordingly, damage of frictional surfaces of differential parts. The law of summing up the axial components of all the gearings in two and four pinion differentials depends on combinations of numbers of the side gear's and pinion's teeth. A classification of bevel gear differentials into four groups depending on those combinations has been carried out. Differentials of the four groups have different degrees of the axial force vibration. The paper presents a detailed method to evaluate theoretically the axial forces in each of the groups. As shown, differentials from one of the four groups (Group III) have decreased axial force vibrations.

Through inverse dynamics-based modeling and computer simulations for a 6×6 Unmanned Ground Vehicle (UGV) - a 6×6 truck - in stochastic terrain conditions, this paper analytically presents a coupled impact of different driveline system configurations and a suspension design on vehicle dynamics, including vehicle mobility, and energy efficiency. A new approach in this research work involves an estimation of each axle contribution to the level of potential mobility loss/increase and/or energy consumption increase/ reduction. As it is shown, the drive axles of the vehicle interfere with the vehicle's dynamics through the distribution of the wheels' normal reactions and wheel torques. The interference causes the independent system dynamics to become operationally coupled/fused and thus diminishes vehicle mobility and energy efficiency. The analysis is done by the use of new mobility indices and energy efficiency indices which are functionally coupled/fused.

A new inter-disciplinary degree program has been developed at Lawrence Technological University: the Master of Science in Mechatronic Systems Engineering Degree (MS/MSE). It is one of a few MS-programs in mechatronics in the U.S.A. today. This inter-disciplinary program reflects the main areas of ground vehicle mechatronic systems and robotics. This paper presents areas of scientific and technological principles which the Mechanical Engineering, Electrical and Computer Engineering, and Math and Computer Science Departments bring to Mechatronic Systems Engineering and the new degree program. New foundations that make the basis for the program are discussed. One of the biggest challenges was developing foundations for mechanical engineering in mechatronic systems design and teaching them to engineers who have different professional backgrounds. The authors first developed new approaches and principles to designing mechanical subsystems as components of mechatronic systems.

The field of Vehicle Dynamics as the theory of a vehicle in motion is to study the vehicle's properties (vehicle running abilities) in the interaction of the vehicle and it's surroundings. This interaction itself appears through forces acting on a vehicle. To control these forces leads to control the properties of a vehicle in motion such as tractive and velocity properties, fuel consumption, turnability, ride stability and others. This paper proposes a unique and novel theory of a vehicle in motion. This theory allows parallel control of the forces acting on a vehicle, which leads to considerable improvement of the vehicle's running abilities. This paper presents the interrelation between the criteria of vehicle running abilities and output characteristics of vehicle systems, which control the vehicle forces. To optimize a vehicle's running abilities require optimization of the combinations of forces acting on a vehicle.

Stability of motion, turnability, mobility and fuel consumption of all-wheel drive terrain vehicles strongly depends on engine power distribution among the front and rear driving axles and then between the left and right wheels of each axle. This paper considers kinematic discrepancy, which characterizes the difference of the theoretical velocities of the front and rear wheels, as the main factor that influences power distribution among the driving axles/wheels of vehicles with positively locked front and rear axles. The paper presents a new algorithm which enables minimization of the kinematic discrepancy factor for the improvement of AWD terrain vehicle dynamics while keeping up with minimal power losses for tire slip. Three control modes associated with gear ratio control of the front and rear driving axles are derived to provide the required change in kinematic discrepancy. Computer simulation results are presented for different scenarios of terrain and road conditions.

An open-link locomotion module, comprising a driving wheel with an electric motor, a system of electro-hydraulic suspension, and an electro-hydraulic power steering system, is presented in this paper as the basis for the modular design of unmanned (robotic) ground vehicles. The open-link-type configuration allows the module to be functionally integrated and engineered with a system of similar modules and thus virtually allows to compile vehicles with any required number of driving wheels. The overall dimensions and carrying capacity of the tire used in the module, as well as technical characteristics of the suspension and power steering systems make possible to employ the module for commercial ground vehicle applications. This paper considers technical issues related to designing the locomotion module.

A state-of-the-art review of the technical meaning and application of the term ‘maneuver’, used by the U.S. Army and ground vehicle engineering communities, was performed with regard to various military activities, including modeling and simulation (M&S), to focus on the value and applicability of the term to military vehicle dynamics. As shown, U.S. military doctrine has built through history and experience a unique concept of maneuver-in-general and its application in U.S. Army unified land operations. Yet, the term ‘maneuver’ needs further technical categorization and characterization for the purpose of dynamics of military unmanned ground vehicles (UGVs) and vehicle design for maneuver. While the NHTSA and SAE standards and definitions provide solid foundations for M&S of cars and trucks to enhance the safety of those vehicles (manned and autonomous), occupants, and pedestrians on roads, the standards cannot address all needs of military vehicles in maneuver.

When a vehicle moves over uneven ground, motion of the sprung and unsprung masses causes dynamic shifting in the load transmitted to the ground, making the normal reaction in the tire-soil patch a continuously changing wheel parameter that may affect vehicle performance. At high loads, sinkage of the wheel can become high as the wheel digs into the soil. At low loads, the wheel can have difficulty acquiring sufficient traction. Additionally, steerability of the wheel can be diminished at very low loads. Controlling the damping forces in the suspension that is usually used to improve ride quality and stabilize motion of the sprung mass can result in an increase in the dynamic variation of the wheel normal reaction and cause vehicle performance deterioration. In this paper, a method is developed to establish boundary constraints on the dynamic normal reaction to maintain reasonable tire-terrain mobility characteristics.

While much research has focused on improving terrain mobility, energy and fuel efficiency of terrain trucks, only a limited amount of investigation has gone into analysis of power distribution between the driving wheels. Distribution of power among the driving wheels has been shown to have a significant effect on vehicle operating characteristics for a given set of operating conditions and total power supplied to the wheels. Wheel power distribution is largely a function of the design of the driveline power dividing units (PDUs). In this paper, 6×6/6×4 terrain truck models are analyzed with the focus on various combinations of PDUs and suspension systems. While these models were found to have some common features, they demonstrate several different approaches to driveline system design.