Search Results

A carburetted, spark ignited gasoline fuelled engine of a 5 kW rated power generator was converted to run on hydrogen. As opposed to large parts of current research, the engine conversion’s foremost goal was not to maximise efficiency and power output but rather to find a cost-effective and low-complexity conversion approach to introduce clean fuels to existing engines. To allow for the increased volumetric fuel flow, the riser of the original carburettor was enlarged. The hydrogen flow into the venturi was metered with the help of a pressure regulator from a widely available conversion kit. The effects of different hydrogen-fuel-feed pressures on engine performance, operational stability and emission levels were examined experimentally. It was found that the hydrogen-line pressure before startup has to be set precisely (±5 mbar) to allow for stable and emission free operation.

The present work investigates the effect of fuel injection timing on combustion stratification and soot formation in an optically accessible, single cylinder light duty diesel engine. The engine operated under low load and low engine speed conditions, employing a single injection scheme. The conducted experiments considered three different injection timings, which promoted Partially Premixed Combustion (PPC) operation. The fuel quantity of the main injection was adjusted to maintain the same Indicated Mean Effective Pressure (IMEP) value among all cases considered. Findings were analysed via means of pressure trace and apparent heat transfer rate (AHTR) analyses, as well as a series of optical diagnostics techniques, namely flame natural luminosity, CH* and C2* chemiluminescence high-speed imaging, as well as planar Laser Induced Incandescence (pLII).

In Gasoline Direct Injection engines, direct exposure of the injector to the flame can cause combustion products to accumulate on the nozzle, which can result in increased particulate emissions. This research observes the impact of injector fouling on particulate emissions and the associated injector spray pattern and shows how both can be reversed by utilising fuel detergency. For this purpose multi-hole injectors were deliberately fouled in a four-cylinder test engine with two different base fuels. During a four hour injector fouling cycle particulate numbers (PN) increased by up to two orders of magnitude. The drift could be reversed by switching to a fuel blend that contained a detergent additive. In addition, it was possible to completely avoid any PN increase, when the detergent containing fuel was used from the beginning of the test. Microscopy showed that increased injector fouling coincided with increased particulate emissions.

The purpose of this work was to gain a fundamental understanding of which fuel property parameters are responsible for particulate emission characteristics, associated with key intermediate behavior in the engine cylinder such as the fuel film and insufficient mixing. Accordingly, engine tests were carried out using various fuels having different volatility and chemical compositions under different coolant temperature conditions. In addition, a fundamental spray and film visualization analysis was also conducted using a constant volume vessel, assuming the engine test conditions. As for the physical effects, the test results showed that a low volatility fuel displayed high particulate number (PN) emissions when the injection timing was advanced. The fundamental test clearly showed that the amount of fuel film on the impingement plate increased under such operating conditions with a low volatility fuel.

The present work investigates the effect of low levels CO2 addition on the combustion characteristics inside a single cylinder optical engine operated under low load conditions. The effects of dilution levels (up to 7.5% mass flow rate CO2 addition), the number of pilot injections (single or double pilot injections) and injection pressure (25 or 40 MPa), are evaluated towards the direction of achieving a partially premixed combustion (PPC) operation mode. The findings are discussed based on optical measurements and via pressure trace and apparent rate of heat release analyses in a Ricardo Hydra optical light duty diesel engine. The engine was operated under low IMEP levels of the order of 1.6 bar at 1200 rpm and with a CO2 diluent-enhanced atmosphere resembling an environment of simulated low exhaust gas recirculation (EGR) rates. Flame propagation is captured by means of high speed imaging and OH, CH and C2 line-of-sight chemiluminescence respectively.

The measurement of the rate of fuel injection using a constant volume, fluid filled chamber and measuring the pressure change as a function of time due to the injected fluid (the so called “Zeuch” method) is an industry standard due to its simple theoretical underpinnings. Such a measurement device is useful to determine key timing and quantity parameters for injection system improvements to meet the evolving requirements of emissions, power and economy. This study aims to further the understanding of the nature of cavitation which could occur in the near nozzle region under these specific conditions of liquid into liquid injection using high pressure diesel injectors for heavy duty engines. The motivation for this work is to better understand the temporal signature of the pressure signals that arise in a typical injection cycle.

The aim of this paper is to extend the evaluation of the accuracy of published 1-D pressure loss coefficients which are used in 1-D gas dynamics models, in unsteady compressible flows propagating in the exhaust pulses in manifolds. These pressure loss coefficients were derived from the conservation of linear momentum over finite control volumes based on assumptions including steady flow. The objectives of this work were to evaluate the accuracy of the pressure loss coefficients over the type of flows generated by engine-like pressure pulses propagating in a range of three-pipe junctions. The evaluation was performed by reference to results from unsteady, compressible, 3-D Reynolds-averaged computational fluid dynamic (CFD - open source software OpenFOAM) simulations. Two of the junction branches represented the exhaust pipes from two cylinders and the remaining was the outlet pipe. All pipes had a diameter of 25mm with length ratio 1:2 between inlet and outlet.

Spray characteristics of injectors depend on, among other factors, not only the level of turbulence upstream of the nozzle plate, but also on whether cavitation arises. "Bulk" cavitation, by which we mean cavitation which arises far from walls and thus far from streamline curvature associated with salient points on a wall, has not been investigated thoroughly experimentally and moreover it is quite challenging to predict by means of computational fluid dynamics. Information about the effect of the injector geometry on the formation of bulk cavitation and quantitative measurements of the flow field that promotes this phenomenon in gasoline injectors does not exist and this forms the background to this work. Evolution of bulk cavitation was visualized in two gasoline multi-hole injectors by means of a fast camera.

This study measures, during various transients of speed and load, in-cylinder-, intake-/exhaust- (manifold) pressures and engine torque. The tests were conducted on a typical high power-density, passenger car powertrain (common-rail diesel engine, of in-line 4-cylinder configuration equipped with a Variable Geometry Turbocharger). The objective was to quantify the deterioration (relative to a steady-steady condition) in transient Specific Fuel Consumption (SFC) that may occur during lagged-boost closed-loop control and thus propose an engine control strategy that minimises the transient SFC deterioration. The results, from transient characterisation and the analysis method applied in this study, indicate that transient SFC can deteriorate up to 30% (function of load transient) and is primarily caused by excessive engine pumping-loss.

The study measured Mass Air Flow, (MAF), Manifold Absolute Pressure, (MAP), and emissions of NO and soot during fourteen transients of speed and load, representative of the Extra Urban Drive Cycle (EUDC). The tests were conducted on a typical passenger car/light-duty truck powertrain (a turbocharged common-rail diesel engine, of in-line 4-cylinder configuration). The objective was to compare NO and soot with corresponding steady-state emission results and propose an engine measurement methodology that will potentially quantify deviation (i.e. deterioration with respect to steady state optimum) in emissions of NO and soot during transients. Comparison between steady state, quasi-steady-states (defined later in the paper) and transients indicated that discrete quasi-steady-state engine operation, can be used for accurate prediction of transient emissions of NO and soot.

The spray characteristics of a gasoline injector depend not only on the physics of atomization of the liquid jet on exit from the nozzle plate but also on the level of turbulence generated by the internal flow, upstream of the nozzle plate, as well as on whether cavitation arises. Measurement of the internal flow field of an injector can thus provide useful information and can assist the evaluation of the accuracy of computer predictions of the flow and associated cavitation. Information about the flow field upstream of nozzle exits is, however, rare and this forms the background to this work. Two-Dimensional Micro Particle Imaging Velocimetry (μPIV) was employed to measure the internal flow field in planes parallel to a plane of symmetry of the injector, downstream of the needle valve centring boss of a 10:1 super-scale transparent model of an 8-nozzle gasoline injector, with exit model-nozzle diameters of 2mm and a fixed model-needle lift of 0.8mm.

An optically accessed, single-cylinder engine capable of operating at both spark ignition and Homogeneous Charge Compression Ignition (HCCI) combustion was used to investigate the difference in the initiation and development of HCCI combustion due to charge stratification, internal Exhaust Gas Recirculation (iEGR) or spark discharge. Natural-light images were acquired to visualise the differences in chemiluminescent structure (i.e. reaction structures) at the early and late stages of formation during HCCI combustion in an attempt to find better ways of controlling HCCI combustion at low and high loads. Regardless of charge stratification, the cycle-to-cycle deviation of autoignition from temporal and spatial repeatability was comparatively small. Flame initiation appeared initially at single or spatially adjacent sites and we did not observe the growth of any new, (i.e. “secondary” in time) reacting ‘islands’ separate from the original sites.

A high-swirl, low Compression Ratio (CR), optically accessed engine that was able to produce a stratified charge was used to investigate the differences in HCCI combustion and in the propagation of the autoignition front between a non-stratified and a stratified charge. Furthermore the relevance of charge stratifying an engine using variable injection timing with large temperature inhomogeneities was investigated. The CHEMKIN code and a detailed reaction mechanism were used to simulate the fuel chemistry of ignition and combustion in a low CR engine. The aim of the simulation was to quantify the effect of initial mixture temperature, Ti and A/F ratio on cool flame and main ignition timing and to evaluate the possibility of charge stratifying our engine.