Search Results

The paper presents a numerical study aimed at converting a commercial lightweight 2-Stroke Indirect Injection (IDI) Diesel aircraft engine to Direct Injection(DI). First, a CFD-1D model of the IDI engine was built and calibrated against experiments at the dynamometer bench. This model is the baseline for the comparison between the IDI and the DI combustion systems. The DI chamber design was supported by extensive 3D-CFD simulations, using a customized version of the KIVA-3V code. Once a satisfactory combustion system was identified, its heat release and wall transfer patterns were entered in the CFD-1D model, and a comparison between the IDI and the DI engine was performed, considering the same Air-Fuel Ratio limit. It was found that the DI combustion system yields several advantages: better take-off performance (higher power output), lower fuel consumption at cruise conditions, improved altitude performance, reduced cooling requirements.

In this work, the authors assess the potential of the 2-stroke concept applied to Range Extender engines, proposing 3 different configurations: 1) Supercharged, Compression Ignition; 2) Turbocharged, Compression Ignition; 3) Supercharged, Gasoline Direct Injection. All the engines feature a single power cylinder of 0.49l, external air feed by piston pump and an innovative induction system. The scavenging is of the Loop type, without poppet valves, and with a 4-stroke like lubrication system (no crankcase pump). Engine design has been supported by CFD simulations, both 1D (engine cycle analysis) and 3D (scavenging, injection and combustion calculations). All the numerical models used in the study are calibrated against experiments, carried out on engines as similar as possible to the proposed ones.

The paper describes a numerical study, supported by experiments, on light aircraft 2-Stroke Direct Injected Diesel engines, typically rated up to 110 kW (corresponding to about 150 imperial HP). The engines must be as light as possible and they are to be directly coupled to the propeller, without reduction drive. The ensuing main design constraints are: i) in-cylinder peak pressure as low as possible (typically, no more than 120 bar); ii) maximum rotational speed limited to 2600 rpm. As far as exhaust emissions are concerned, piston aircraft engines remain unregulated but lack of visible smoke is a customer requirement, so that a value of 1 is assumed as maximum Smoke number. For the reasons clarified in the paper, only three cylinder in line engines are investigated. Reference is made to two types of scavenging and combustion systems, designed by the authors with the assistance of state-of-the-art CFD tools and described in detail in a parallel paper.

This paper presents a methodology for the 3D CFD simulation of the intake and compression processes of four stroke internal combustion engines.The main feature of this approach is to provide very accurate initial conditions by means of a cost-effective initialization step. Calculations are applied to a low stroke-to-bore SI engine, operated at full load and maximum engine speed. It is demonstrated that initial conditions for this kind of engines have an important influence on flow field development, particularly in terms of mean velocities close to the firing TDC. Simulation results are used to discuss the choice of a set of parameters for the flow field characterization of low stroke-to-bore engines, as well as to provide an insight into the flow patterns during the overlapping period.

The Department of Mechanical and Civil Engineering (DIMeC) of the University of Modena and Reggio Emilia is developing a new type of small capacity HSDI 2-Stroke Diesel engine, featuring a specifically designed combustion system. The present paper is focused on the analysis of the combustion process, investigated by means of a customized version of the KIVA-3V code. A four stroke automobile Diesel engine featuring a very close bore size is taken as a reference, for both the numerical models calibration and for a comparison with the 2-Stroke engine. Such a comparison clearly demonstrates the effectiveness of the two stroke concept in terms of emissions reduction and high power density.

The Department of Mechanical and Civil Engineering (DIMeC) of the University of Modena and Reggio is developing a new concept of small capacity HSDI 2-Stroke Diesel engine, featuring a specifically designed combustion system. The paper reviews the 2-Stroke engine design process, supported by CFD simulations, both 1D and multi-dimensional. A four stroke automobile Diesel engine is taken as a reference for a theoretical comparison in terms of brake performance at both full and partial load. This comparison shows the potential of the 2-Stroke, as an ultra-compact, efficient and clean engine.

The supercharging system investigated in this study is made up of a traditional turbocharger, coupled with a Roots-type positive displacement compressor. An electrically actuated clutch allows the compressor to be disengaged from the engine at high speed and under partial load steady operations (such as the ones occurring in a driving cycle). This concept of supercharging has been applied to the downsizing of a reference engine (a 2.5 litre, turbocharged, four cylinder, high speed DI Diesel engine), without penalization on the maximum brake power (110 kW) and transient response. For such a purpose, a “paper” engine has been theoretically characterized. The gross engine parameters have been optimised by means of 1-D numerical simulations, using a computational model previously validated against experiments. Performances of the reference and the downsized engine have been compared, considering both steady and transient operating conditions, full and partial load.

Two-stroke diesel engines could be a promising solution for reducing carbon dioxide (CO2) emissions from light-duty vehicles. The main objective of this study was to assess the potential of two-stroke engines in achieving a substantial reduction in CO2 emissions compared to four-stroke diesel baselines. As part of this study 1-D models were developed for loop scavenged two-stroke and opposed piston two-stroke diesel engine concepts. Based on the engine models and an in-house vehicle model, projections were made for the CO2 emissions for a representative light-duty vehicle over the New European Driving Cycle and the Worldwide Harmonized Light Vehicles Test Procedure. The loop scavenged two-stroke engine had about 5-6% lower CO2 emissions over the two driving cycles compared to a state of the art four-stroke diesel engine, while the opposed piston diesel engine had about 13-15% potential benefit.

Hybridization is a mainstream technology for automobiles, and its application is rapidly expanding in other fields. Marine propulsion is one such field that could benefit from electrification of the powertrain. In particular, for boats to sail in enclosed waterways, such as harbors, channels, lagoons, a pure electric mode would be highly desirable. The main challenge to accomplish hybridization is the additional weight of the electric components, in particular the batteries. The goal of this project is to replace a conventional 4-stroke turbocharged Diesel engine with a hybrid powertrain, without any penalty in terms of weight, overall dimensions, fuel efficiency, and pollutant emissions. This can be achieved by developing a new generation of 2-Stroke Diesel engines, and coupling them to a state-of-the art electric system. For the thermal units, two alternative designs without active valve train are considered: opposed piston and loop scavenged engines.

In recent years, interest has been growing in the 2-Stroke Diesel cycle, coupled to high speed engines. One of the most promising applications is on light aircraft piston engines, typically designed to provide a top brake power of 100-200 HP with a relatively low weight. The main advantage yielded by the 2-Stroke cycle is the possibility to achieve high power density at low crankshaft speed, allowing the propeller to be directly coupled to the engine, without a reduction drive. Furthermore, Diesel combustion is a good match for supercharging and it is expected to provide a superior fuel efficiency, in comparison to S.I. engines. However, the coupling of 2-Stroke cycle and Diesel combustion on small bore, high speed engines is quite complex, requiring a suitable support from CFD simulation.

The paper aims at providing information about the influence of the combustion chamber shape on the combustion process evolution in a high speed direct injection (HSDI) small unit displacement engine for off-highway applications. Small HSDI Diesel engines require a deep optimisation process in order to maximize specific power output, while limiting pollutant emissions without additional expensive pollutant aftertreatment equipments. Making reference to a current production engine, the purpose of this paper is to investigate the influence of combustion chamber design on both engine performances and combustion efficiency. The actual piston omega-shape is progressively distorted in order to assess the influence of some of the main bowl-features on both mean-flow evolution, mixture formation and pollutants.

The paper describes a CFD multidimensional and multicycle engine analysis applied to a novel 2-Stroke HSDI Diesel engine, under development since a few years at the University of Modena and Reggio Emilia. In particular, six operating conditions are considered, two of them at full load and four at partial. The simulation tool is STAR-CD, a commercial software extensively applied by the authors to HSDI Diesel engines. Furthermore, an experimental calibration of the combustion model has been performed and reported in this paper, carrying out CFD simulations on a reference Four Stroke HSDI Diesel engine. As expected, in the multi-cycle analysis a wide dependence of pollutants on trapped charge composition has been found. Much less relevant is the cycle-by-cycle variation in terms of performance parameters, such as trapped mass, IMEP, combustion efficiency, etc.

The third generation of biodiesels, derived from microalgae, is one of the most interesting options for the replacement of fossil fuels. While the use of first generation biodiesels on different types of compression ignition engines is well documented in the open literature, much less information is available on algal fuels. As a matter of fact, the influence on combustion and pollutant emissions is not definitively assessed, depending on the combination of the specific features of both fuel and engine. The aim of this paper is to analyze the combustion process in a small industrial engine fueled by an algal Biodiesel, blended with standard Diesel fuel. The blend composition is the one typically used in most applications, i.e. 20% of biodiesel and 80% of Diesel (B20).

Enhanced calibration strategies and innovative engine combustion technologies are required to meet the new limits on exhaust gas emissions enforced in the field of marine propulsion and on-board energy production. The goal of the paper is to optimize the control parameters of a 4.2 dm3 unit displacement marine DI Diesel engine, in order to enhance the efficiency of the combustion system and reduce engine out emissions. The investigation is carried out by means of experimental tests and CFD simulations. For a better control of the testing conditions, the experimental activity is performed on a single cylinder prototype, while the engine test bench is specifically designed to simulate different levels of boosting. The numerical investigations are carried out using a set of different CFD tools: GT-Power for the engine cycle analysis, STAR-CD for the study of the in-cylinder flow, and a customized version of the KIVA-3V code for combustion.

The paper presents a numerical investigation, aimed to explore the potential of 2-stroke Diesel engines, able to meet Euro VI requirements, for application to medium size commercial vehicles (power rate: 80 kW at 2600 rpm, max. torque 420 Nm from 1200 to 1400 rpm). The study is based on experimental performance of a highly developed 4-stroke engine. Two different designs are considered: Loop and Uniflow scavenging, the latter obtained through an opposed piston configuration. In both cases, no poppet valves are used, and the lubrication is provided by a 4-stroke-like oil sump. The study started with the development of a 4-stroke EURO VI engine, on the basis of a previous EURO IV version. A prototype of the new engine (named 430) was built and tested.

An experimental and computational analysis has been performed on the combustion chamber of a two cylinder, four stroke, four valve, spark ignition engine developed by Ducati Motor SpA for the Super Sport Championship. Two cylinder head configurations have been analyzed by using a three dimensional CFD code. Port and valve assemblies do not change. Only the combustion chamber surface changes in order to improve the intake flow. Head flow performances in terms of permeability have been determined by computing the steady discharge coefficients at different valve lifts. These values have also been measured on a steady flow test bench. Head flow performances in terms of flow conditioning, i.e. the attitude to promote tumbling and enhance combustion, have been determined by computing the equivalent solid body tumbling number of the flow field at intake bottom dead center.

The paper reviews the transformation of a 2.8 litre, 4 cylinder, turbocharged Diesel engine, produced by VM Motori (Cento, Italy), into a Compressed Natural Gas (CNG) naturally aspirated power unit. The main goal of the project is to keep an about constant top power value, minimizing engineering costs. The development of the new engine has been supported by experiments and 1D cycle simulations. A first prototype has been built and extensively tested at the dynamometer bench. These data helped the validation of the simulation model, which has been used as an optimisation tool, addressing the next steps of the development process.

2-stage supercharging applied to HSDI Diesel engines appears a promising solution for enhancing rated power, low end torque, transient response and hence the launch characteristics of a vehicle. However, many open points still remain, in particular about the impact on emissions control and fuel economy at partial load conditions, generally requiring both high airflow and high EGR rates. The paper analyzes and compares two types of 2-stage supercharging systems: a) two turbochargers of different size; b) one turbocharger coupled to a positive displacement compressor. The goal of the paper is to assess pro and cons of the most feasible configurations for a typical automobile Diesel engine, complying with Euro V regulations and beyond. The base engine is the 2.8L, 4 cylinder in-line unit produced by VM Motori (Cento, Italy), equipped by a standard variable geometry turbocharger.

The paper compares two different design concepts for a range extender engine rated at 30 kW at 4500 rpm. The first project is a conventional 4-Stroke SI engine, 2-cylinder, 2-valve, equipped with port fuel injection. The second is a new type of 2-Stroke loop scavenged SI engine, featuring a direct gasoline injection and a patented rotary valve for enhancing the induction and scavenging processes. Both power units have been virtually designed with the help of CFD simulation. Moreover, for the 2-Stroke engine, a prototype has been also built and tested at the dynamometer bench, allowing the authors to make a reliable theoretical comparison with the well assessed 4-Stroke unit.

The internal combustion engine (ICE) for a series hybrid vehicle must be very compact, fuel efficient reliable and clean; furthermore it should possess excellent NVH features; finally, the cost should be as low as possible. An unconventional but not exotic solution, potentially ideal to fulfill all the above mentioned requirements, is represented by a 2-Stroke externally scavenged GDI engine, without poppet valves. BRC (Cherasco, Italy) and PRIMAVIS (Turin, Italy) are currently developing an engine of this type, incorporating a patented rotary valve for the control of the charge induced to cylinder. The development is supported by extensive CFD simulations, which are able to predict all the main engine performance characteristics. The paper analyzes, from a theoretical point of view, the installation of the engine on an electric vehicle, previously optimized for a small Diesel engine (Smart 0.8 l CDi).