Search Results

A well balanced use of alternative fuels is an important objective for a sustainable development of individual transportation worldwide. Several countries have objectives to substitute a part of the energy of traffic by ethanol as the renewable energy source. Investigations of limited and unregulated emissions of two 2-S scooters with gasoline-ethanol blend fuels have been performed in the present work according to the measuring procedures, which were established in the previous research in the Swiss Scooter Network (since 2000). The investigated fuels contained ethanol (E), in the portion of 5, 10, 15 and 20% by volume. The investigated 2-S scooters represented a newer and an older 2-stroke technology with carburettor. The newer one was investigated with and without catalyst and the older one only in the original state without catalyst.

Butanol, a four-carbon alcohol, is considered in the last years as an interesting alternative fuel, both for Diesel and for gasoline application. Its advantages for engine operation are: good miscibility with gasoline and diesel fuels, higher calorific value than ethanol, lower hygroscopicity, lower corrosivity and possibility of replacing aviation fuels. Like ethanol, butanol can be produced as a biomass-based renewable fuel or from fossil sources. In the research project, DiBut (Diesel and butanol) addition of butanol to Diesel fuel was investigated from the points of view of engine combustion and of influences on exhaust aftertreatment systems and emissions. One investigated engine (E1) was with emission class “EU Stage 3A” for construction machines, another one, engine (E2) was HD Euro VI. The most important findings are: with higher butanol content, there is a lower heat value of the fuel and there is lower torque at full load.

In the diesel sector the fatty acid methyl esters (FAME's) - in Europe mostly RME (rapeseed methyl ester) and in US mostly SME (soja oil methyl ester) - are used as a various share, % volume blends with the diesel fuel (B5, B7, B10, B20, Bxx). The present joint project focuses on RME being the most important representative of the biofuels of 1st generation in Europe. The influences of RME blend fuels on emissions and on lube oil deterioration are emphasized. Emissions were investigated on a modern engine with exhaust gas aftertreatment devices like SCR and (DPF+ SCR). Beside the legally limited exhaust emission components some non-legislated like NO₂, N₂O, NH₃ and nanoparticles were measured at stationary and dynamic engine operation.

Analysis of non-legislated engine-emission components, with different exhaust-gas after-treatment techniques, is an important air quality objective. This paper reports the results for various nitrogen oxides, ammonia and differentiated hydrocarbons emitted at part load from a small 4-S SI engine. It was operated with gasoline, with CNG and with two different three-way catalytic converters. CNG produces less HC and less aromatics. But the HC conversion rate is insufficient. This is due to the lower exhaust gas temperatures, at part load with CNG, and due to the higher stability of light HCs. CNG affects the λ-regulation window, of the investigated system, such that the NOx conversion rate is lowered. In the rich domain of the λ-regulation window, the NO & NOx emissions after catalyst were lowest, while the NH₃ formation was most intense, and vice versa.

During the VERT *) testing of different DPF systems it was remarked, that the oxidation catalyst converts sometimes a big part of NO to NO2, producing on the one hand a more toxic composition of the exhaust gases and causing on the other hand measuring artefacts, which tend to underestimate of NO2 and NOx by the cold NOx - measurement. The present work summarizes the experiences in this matter elaborated at the Laboratories for IC-Engines & Exhaust Emissions Control (AFHB) of the University of Applied Sciences Biel-Bienne, Switzerland, during several VERT activities and didactic projects on engine and chassis dynamometers in the years 2000-2006.

Limited and non-regulated emissions of scooters were analysed during several annual research programs of the Swiss Federal Office of Environment (BAFU) *). Small scooters, which are very much used in the congested centers of several cities, are a remarkable source of air pollution. Therefore every effort to reduce the emissions is an important contribution to improve the air quality in urban centers. In the present work detailed investigations of particle emissions of different 2-stroke scooters with direct injection and with carburettor were performed. The nanoparticulate emissions were measured by means of SMPS, (CPC) and NanoMet. Also the particle mass emission (PM) was measured with the same method as for Diesel engines. Extensive analyses of PM-residuum for SOF/INSOF, PAH and toxicity equivalence (TEQ), were carried out in an international project network. Particle mass emission (PM) of 2-S Scooters consists mostly of SOF.

A modern HD-Diesel engine for construction machines, Liebherr D 934L (120kW) was set-up for a monofuel operation with crude, cold pressed rapeseed oil (ROR)*). The engine was equipped with a supplementary fuel filtration, supplementary engine & fuel heating for cold start and an appropriate fuel temperature control for the engine operation. A special lube oil was applied. After an extensive basic research of emissions including nanoparticles and energy consumption some adaptations of engine setting were performed: modification of the camshaft to eliminate the internal EGR (same valve timing and lift), earlier start of injection (SOI) at high- and full load, application of a combined exhaust gas aftertreatment system DPF+SCR, testing of DPF+SCR according to the VERT quality verification procedure.

An active oxidation catalyst is an efficient measure to reduce not only gaseous components (CO, HC), but also particle emissions (mostly oil condensates) of a small 2-stroke engine with lost oil lubrication. Since the 2- and 3-wheelers with 2-stroke propulsion are still a very serious source of air pollution worldwide in many urban areas, it is important to have a look on some consequences of an improperly working catalyst. The present paper shows some results of user-oriented aging of catalyst on the vehicle and results of limited emissions and unlimited (nano)particles during the catalysts screening tests. The works are a part of an international scooter network project, which was performed (2004 to 2007) in the Laboratories for IC-Engines & Exhaust Emission Control of the University of Applied Sciences, Biel, Switzerland with main support of the Swiss Federal Office of Environment (BAFU), Swiss Petrol Union (EV) and Swiss Lubes (VSS).

Advances in emission control technologies have demanded development of new ceramic chemistries and improved microstructures in catalytic substrates and especially in diesel particulate filters. High porosity filters are desirable, as they decrease engine backpressure and enable application of advanced catalysts including, but not limited to, multi-functional filters (MFF). A significant recent development has been in the use of ceramic fibers to create cross-linked microstructures in extruded honeycomb ceramics. This development allows high porosities to be attained while maintaining mechanical strength. However, according to the World Health Organization, certain classes of ceramic fibers are considered to have adverse health effects if released in air and inhaled.

New Diesel exhaust gas aftertreatment systems, with combined DPF*) and deNOx (mostly SCR) systems represent a very important step towards zero emission Diesel fleet. These combined systems are already offered today by several suppliers for retrofitting of HD vehicles. Reliable quality standards for those quite complex systems are urgently needed to enable decisions of several authorities. The present report informs about the international network project VERT *) dePN (de-activation, de-contamination, disposal of particles and NOx), which was started in Nov. 2006 with the objective to introduce the SCR-, or combined DPF+SCR-systems in the VERT verification procedure. Examples of results for some of the investigated systems are given. These investigations included parameters, which are important for the VERT quality testing: besides the regulated gaseous emissions several unregulated components such as NH3, NO2 and N2O were measured.

2- and 3-wheelers with 2-S propulsion are still a very serious source of air pollution worldwide in many urban areas. Therefore, every effort to reduce the emissions of those vehicles is an important contribution to improve the air quality. In the present work detailed investigations of regulated emissions and of particle emissions of 2-stroke scooters with direct injection and with carburator were performed. To demonstrate the emission reduction potentials some possibilities of emission improvements were grouped into steps. These technical measures were: ○ Higher tier lube oils ○ Lower oil dosing ○ Active oxidation catalyst ○ Supplementary filtration & oxidation devise (WFC) **) ○ Special fuel. Particle mass and nanoparticles (number), which are amply present in 2-stroke exhaust gas and which contribute strongly to the toxicity level are still unlimited by the international exhaust gas legislation. They were extensively investigated in the present project series.

Concern for engine particle emission led to EC regulations of the number of solid particles emitted by LDV and HDV. However, all conventional piston-driven combustion engines emit metal oxide particles of which only little is known. The main sources are abrasion between piston ring and cylinder, abrasion of bearing, cams and valves, catalyst coatings, metal-organic lubrication oil additives, and fuel additives. While abrasion usually generates particles in the μm range, high concentrations of nanosize metal oxide particles are also observed, probably resulting from nucleation processes during combustion. In general, metal oxides, especially from transition metals, have high surface reactivity and can therefore be very toxic, especially nanosize particles, which evidently provide a high specific bioactive surface and are suspected to penetrate into the organism. Hence, these particles must be scrutinized for quantity, size distribution and composition.

The objectives of the present work are to investigate the regulated and unregulated (particle) emissions of a classical and modern 2-stroke and a typical 4-stroke scooter with different ethanol blend fuels. There is also comparison of two different ethanol fuels: pure ethanol (E) *) and hydrous ethanol (EH) which contains 3.9% water and is denatured with 1.5% gasoline. Special attention is paid in this research to the hydrous ethanol, since the production costs of hydrous ethanol are much less than those for (dry) ethanol. The vehicles are with carburettor and without catalyst, which represents the most frequent technology in Eastern Asia and offers the information of engine-out emissions. Exhaust emissions measurements have been performed with fuels containing ethanol (E), or hydrous ethanol (EH) in the portion of 5, 10, 15 and 20% by volume. During the test systematical analysis of particle mass (PM) and nano-particles counts (NP) were carried out.

1 Analysis of limited and nonlimited emissions of scooters was performed during several research programs of the Swiss Federal Office of Environment Forests and Landscape (FOEFL) - and as a contribution to the European project ARTEMIS*). Small scooters, which are very much used in the congested centers of the European cities are a remarkable source of air pollution. Therefore every effort to reduce the emissions is an important contribution to improve the air quality in urban centers. In the present work detailed investiga-tions of a Peugeot scooter with TSDI (Two Stroke Direct Injection) were per-formed and the emissions were compa-red to the other 2-S & 4-S scooters. As nonlimited emissions the nanopar-ticulate emissions at cold and warm operating conditions were measured by means of SMPS, ELPI and NanoMet*). The measurements were both: at steady state and at transient operating conditions.

1 During the research programs of the Swiss Federal Office of Environment Forests and Landscape (FOEFL) - and as a contribution to to the European project ARTEMIS*) analysis of limited and nonlimited emissions of motorcycles was performed. Exhaust emissions measurements of two motorcycles without catalyst: 4-stroke 750 cc and 1100 cc have been performed in the present work. Identical driving cycles have been repeated and the influence of the cooling duration on the emissions at cold start was investigated. A cold start in the temperature range of 20 ÷ 25 °C can be regarded as a “summer cold start”. As nonlimited emissions the nanoparticulate emissions at cold and warm operating conditions were measured by means of SMPS and NanoMe**). The measurements were performed at steady state and at transient operating conditions. The present work cleared up several details about the emissions of strong motorized motorcycles.

Different Diesel Particle Filters (DPF)*) were tested on a 2-Stroke Detroit-Diesel bus engine 6V 92 TA. The investigations focused on soot burden and regeneration of the DPF with special filter materials. Also examined was promoting the regeneration by: throttling, additive (FBC), oxidation catalytic converter upstream of DPF and the catalytic coating of the filter material. The metrics were the particulate matter emission, its composition and the nanoparticles. The most important results are: The average SOF content in the engine exhaust particulate matter is 77.6 % and the majority of it is emitted as bigger droplets The wire-mesh filter catalyst (WFC) - a novel emission reduction technology -substantially curtails the SOF and PM. WFC traps and oxidizes the oil droplets and produces a “dry” soot. This can be very advantageous for the DPF downstream of WFC. (WFC can be also very interesting for 2-S gasoline engines).

1 Addition of gaseous fuels to the gasoline fuelled SI-engine offers several potentials of improvements, like: cold start without enrichment, lower engine-out emissions, in certain cases better strategy of catalyst heating. In the present work some results of investigations with addition of compressed natural gas CNG*) and of H2-containing reformer gases are presented. Two engines were fuelled with different compositions of H2-CO-CO2-N2 mixtures as model gases for methanol-, or gasoline- reformed fuels. The investigations were performed at warm, stationary, part load operation. Due to the presence of hydrogen the reformer gas causes more advantages, than CNG. It lowers the gaseous emission components, shortens the combustion duration, increases the combustion stability and enables much more expanded lean-limits and EGR-limits. The passive components of the reformer gas (CO2, N2) have similar influence on NOx-reduction as the internal EGR.

In order to meet future requirements for emission reduction and fuel economy a variety of concepts are available for gasoline engines. In the recent past new pathways have been found using alternative fuels and fuel combinations to establish cost optimized solutions. The presented concept for a SI-engine consists of combined injection of gasoline and hydrogen. A hydrogen enriched gas mixture is being injected additionally to gasoline into the engine manifold. The gas composition represents the output of an onboard gasoline reformer. The simulations and measurements show substantial benefits to improve the combustion process resulting in reduced cold start and warm up emissions and optimized part load operation. The replacement of gasoline by hydrogen-rich gas during engine start leads to zero hydrocarbons in the exhaust gas.

1 The topic of investigation of this work was the influence of different gas qualities on the engine parameters and particularly on the air excess factor λ. For this research the normalized gases with extreme compositions were used. At stationary operation there are no differences of the leaning capability of the different gases. The gas with the highest content of inert components causes the lowest full load power, the highest fuel consumption and the highest cyclic irregularity. With the same air flow and the same injection duration for different gases result different air excess factors λ according to the density and to the necessary stoichiometric air quantity of each gas. This fact influences the λ at transient operation conditions as: cold starting, gas quality jump, or load increase, if there is no λ-control. With an active λ-control, which is today fast enough, especially with an adaptive system there are no problems with λ- differences.