Search Results

To downsize a spark ignited (SI) internal combustion engine (ICE), keeping suitable power levels, the application of turbocharging is mandatory. The possibility to couple an electric drive to the turbocharger (electric turbo compound, ETC) can be considered, as demonstrated by a number of studies and the current application in the F1 Championship, since it allows to extend the boost region to the lowest ICE rotational speeds and to reduce the turbo lag. As well, some recovery of the exhaust gas residual energy to produce electrical energy is possible. The present paper shows the first numerical results of a research program under way in collaboration between the Universities of Pisa and Genoa. The study is focused on the evaluation of the benefits resulting from the application of ETC to a twin-cylinder small SI engine (900 cm3).

Storing hydrogen is one of the major issues concerning its utilization on board vehicles. A promising solution is storing hydrogen in the form of ammonia that contains almost 18% hydrogen by mass and is liquid at roughly 9 bar at environmental temperature. As a matter of fact, liquid ammonia contains 1.7 times as much hydrogen as liquid hydrogen itself, thus involving relatively small volumes and light and low-cost tanks. It is well known that ammonia can be burned directly in I.C. engines, however a combustion promoter is necessary to support and speed up combustion especially in the case of high-speed S.I. engines. The best promoter is hydrogen, due to its opposed and complementary characteristics to those of ammonia, Hydrogen has high combustion velocity, low ignition energy and wide flammability range, whereas ammonia has low flame speed, narrow flammability range, high ignition energy and high self-ignition temperature.

Due to concerns regarding pollutant and CO2 emissions, advanced combustion modes that can simultaneously reduce exhaust emissions and improve thermal efficiency have been widely investigated. The main characteristic of the new combustion strategies, such as HCCI and LTC, is that the formation of a homogenous mixture or a controllable stratified mixture is required prior to ignition. The major issue with these approaches is the lack of a direct method for the control of ignition timing and combustion rate, which can be only indirectly controlled using high EGR rates and/or lean mixtures. Homogeneous Charge Progressive Combustion (HCPC) is based on the split-cycle principle. Intake and compression phases are performed in a reciprocating external compressor, which drives the air into the combustor cylinder during the combustion process, through a transfer duct. A transfer valve is positioned between the compressor cylinder and the transfer duct.

Storing hydrogen is one of the major problems concerning its utilization on board vehicles. Today hydrogen can be compressed and stored at 200 or 350 bar (it is foreseen that in a near future storage pressure will reach 700 bar, according to new expected regulations and using tanks in composite materials) or cryogenically liquefied. An alternative solution is storing hydrogen in the form of ammonia that is liquid at roughly 9 bar at environmental temperature and therefore involves relatively small masses and volumes and requires light and low-cost tanks. Moreover, ammonia contains almost 18% hydrogen by mass and, by volume, liquid ammonia contains 1.7 times as much hydrogen as liquid hydrogen. It is well known that ammonia can be burned directly in I.C. engines, however a combustion promoter is necessary to support combustion especially in the case of high-speed S.I. engines.

An innovative hydrogen DI system was conceived, realized and tested that requires only 12 bar rail pressure, typical value of PFI systems, and does not need special injectors. The purpose is to combine the well-known benefits of DI with the ones of PFI. The injection is accomplished in two steps: at first hydrogen, metered by an electroinjector (a conventional one for CNG application), enters a small intermediate chamber; then it is injected into the cylinder by means of a mechanically actuated valve that allows very high flow rate (compared with the one of electroinjectors). In-cylinder injection starts at intake valve closing (an earlier injection start could lead to backfire) and stops early enough to allow proper charge homogeneity and, in any case, before cylinder pressure rise constrains hydrogen admission. The prototype engine was realized modifying a production single-cylinder 650 cm₃ engine with three intake valves.

This paper concerns an innovative concept to control HCCI combustion in diesel-fuelled engines. It was named Homogenous Charge Progressive Combustion (HCPC) and operates on the split-cycle principle. In previous papers the feasibility of this combustion concept was shown for light-duty diesel engines. This paper illustrates a CFD study concerning a heavy-duty version of the HCPC engine. The engine displaces 13 liters and develops 700 kW indicated power at 2200 rpm with 49% maximum indicated efficiency and clean combustion.

The paper describes the CFD analysis, the arrangement and the first experimental results of a single-cylinder engine that employs an innovative low-pressure hydrogen direct-injection system, characterized by low fuel rail pressure (12 bar) and consequent low residual storage pressure. The injection is split in two steps: at first hydrogen is metered and admitted into a small intermediate chamber by an electroinjector (a conventional one usually employed for CNG), next a mechanically actuated poppet valve, that allows high volumetric flow rates, times hydrogen injection from the intermediate chamber to the cylinder within a short time, despite the high hydrogen volume due to the low injection pressure. Injection must be properly timed to maintain pressure below 6 bar (or little more) in the intermediate chamber and thus keep sonic flow through the electroinjector, to maximize volumetric efficiency and to avoid backfire in the intake pipe.

Homogeneous-charge, compression-ignition (HCCI) combustion is triggered by spontaneous ignition in dilute homogeneous mixtures. The combustion rate must be reduced by suitable solutions such as high rates of Exhaust Gas Recirculation (EGR) and/or lean mixtures. HCCI is considered a very effective way to reduce engine pollutant emissions, however only a few HCCI engines have entered into production. HCCI combustion currently cannot be extended to the whole engine operating range, especially to high loads, since the use of EGR displaces air from the cylinder, limiting engine mean effective pressure, thus the engine must be able to operate also in conventional mode. This paper concerns an innovative concept to control HCCI combustion in diesel-fuelled engines. This new combustion concept is called Homogenous Charge Progressive Combustion (HCPC). HCPC is based on split-cycle principle.

Homogeneous-charge, compression-ignition (HCCI) combustion is triggered by spontaneous ignition in dilute homogeneous mixtures. The combustion rate must be reduced by suitable solutions such as high rates of Exhaust Gas Recirculation (EGR) and/or lean mixtures. HCCI is considered a very effective way to reduce engine pollutant emissions, however only a few HCCI engines have entered into production. HCCI combustion currently cannot be extended to the whole engine operating range, especially to high loads, since the use of EGR displaces air from the cylinder, limiting engine mean effective pressure, thus the engine must be able to operate also in conventional mode. This paper concerns a study of an innovative concept to control HCCI combustion in diesel-fuelled engines. The concept consists in forming a pre-compressed homogeneous charge outside the cylinder and gradually admitting it into the cylinder during the combustion process.

A low-pressure hydrogen direct-injection solution is presented that allows some typical benefits of direct injection, such as high specific power and backfire prevention, plus low residual storage pressure, that improves vehicle range and is a typical advantage of external mixture formation. Since the injection must end early enough to allow good charge homogeneity and, in any case, before in-cylinder pressure rise constraints hydrogen admission, especially at heavy loads hydrogen flow to the cylinder is higher than present electro-injectors allow. The injection is realised in two steps: hydrogen flow rate is simply controlled by a conventional CNG electro-injector that feeds a small intermediate chamber. From this chamber hydrogen next enters the cylinder in a short crank angle period by means of a mechanically-actuated valve that opens at the intake valve closure to avoid backfire.

This paper concerns a study of an innovative concept to control HCCI combustion in diesel-fueled engines. The concept consists in forming a pre-compressed homogeneous charge outside the cylinder and in gradually admitting it into the cylinder during the combustion process. This new combustion concept has been called Homogeneous Charge Progressive Combustion (HCPC). CFD analysis was conducted to understand the feasibility of the HCPC concept and to identify the parameters that control and influence this novel HCCI combustion. A CFD code with detailed kinetic chemistry (AVL FIRE) was used in the study. Results in terms of pressure, heat release rate, temperature, and emissions production are presented that demonstrate the validity of the HCPC combustion concept.

Homogeneous charge compression ignition (HCCI) combustion is considered to be an attractive alternative to traditional internal combustion engine operation because of its extremely low levels of pollutant emissions. However, there are several difficulties that must be overcome for HCCI practical use, such as difficult ignition timing controllability. Indeed, too early or too late ignition can occur with obvious drawbacks. In addition, the increase in cyclic variation caused by the ignition timing uncertainty can lead to uneven engine operation. As a way to solve the combustion phasing control problem, dual-fuel combustion has been proposed. It consists of a diesel pilot injection used to ignite a pre-mixture of gasoline (or other high octane fuel) and air. Although dual-fuel combustion is an attractive way to achieve controllable HCCI operation, few studies are available to help the understanding of its in-cylinder combustion behavior.

Two-stroke S.I. engine survival is submitted to direct fuel injection and charge stratification. An exhaustive activity concerning a 50 cm3 two-stroke S.I. engine with liquid direct injection and charge stratification has given really satisfactory results as regards engine aptitude to operate unthrottled at every speed and load. However, unthrottled operation does not necessarily lead to the best overall result. By CFD investigation and experimental tests, this paper proves that some throttling reduces HC and NOx emissions as well as pumping loss and increases exhaust gas temperature at light loads, with evident advantage for catalytic converter efficiency.

High-pressure liquid fuel injection is a suitable means to get either stratified charge or homogeneous charge for two-stroke engines. This paper shows the development of this solution for a small 50 cm3 engine for light motorcycles. By means of computational fluid dynamics, a combustion chamber suitable for proper fuel distribution in every engine operating condition has been designed. It has been realized, and experimental results confirm its fairly satisfactory behaviour, with good fuel economy, low exhaust emissions and small cycle-to-cycle variation even at light loads. Recent CFD studies indicate how to improve engine geometry to achieve a better stratification stability at partial loads independently on engine speed.

In two-stroke S.I. engines, direct fuel injection prevents fuel loss from the exhaust port, since only air is employed for the scavenging process. However, to solve the problem of combustion irregularity at light loads due to excessive presence of residual gas in the charge, fuel injection should also produce charge stratification. An alternative to stratification is ATAC (Active Thermo Atmosphere Combustion), which turns the effect of residual gas from negative to positive, since residual gas energy is exploited to prime the combustion of fresh gas. For the first time, the feasibility of ATAC combined with liquid high-pressure direct injection is proved in this paper. To illustrate the compatibility of ATAC with fuel injection, ATAC behaviours are shown in the cases of liquid high-pressure direct injection, air-assisted medium-pressure direct injection and indirect injection.

A study was performed that takes into account both turbulence and chemical kinetic effects in the numerical simulation of diesel engine combustion in order to better understand the importance of their respective roles at changing operating conditions. An approach was developed which combines the simplicity and low computational and storage requests of the laminar-and-turbulent characteristic-time model with a detailed combustion chemistry model based on well-known simplified mechanisms. Assuming appropriate simplifications such as steady state or equilibrium for most of the radicals and intermediate species, the kinetics of hydrocarbons can be described by means of three overall steps. This approach was integrated in the KIVA-II code. The concept was validated and applied to a single-cylinder, heavy-duty engine. The simulation covers a wide range of operating conditions.