Search Results

One of the issues in stamping of advanced high strength steels (AHSS) is the stretch bending fracture on a sharp radius (commonly referred to as shear fracture). Shear fracture typically occurs at a strain level below the conventional forming limit curve (FLC). Therefore it is difficult to predict in computer simulations using the FLC as the failure criterion. A modified Mohr-Coulomb (M-C) fracture criterion has been developed to predict shear fracture. The model parameters for several AHSS have been calibrated using various tests including the butter-fly shaped shear test. In this paper, validation simulations are conducted using the modified (M-C) fracture criterion for a dual phase (DP) 780 steel to predict fracture in the stretch forming simulator (SFS) test and the bending under tension (BUT) test. Various deformation fracture modes are analyzed, and the range of usability of the criterion is identified.

Advanced high-strength steels (AHSS), due to their significantly higher strength than the conventional high-strength steels, are increasingly used in the automotive industry to meet future safety and fuel economy requirements. Unlike conventional steels, the properties of AHSS can vary significantly due to the different steelmaking processes and their fracture behaviors should be characterized. In crash analysis, a fracture model is often integrated in the simulations to predict fracture during crash events. In this article, crash simulations including a fracture criterion are conducted for a third-generation AHSS, that is, 980GEN3. A generalized incremental stress state dependent damage model (GISSMO) in LS-DYNA is employed to evaluate the fracture predictability in the crash simulations.

Third generation advanced high strength steels (3GAHSS) are increasingly used in automotive for light weighting and safety body structure components. However, high material strength usually introduces higher springback that affects the dimensional accuracy. The ability to accurately predict springback in simulations is very important to reduce time and cost in stamping tool and process design. In this work, tension and compression tests were performed and the results were implemented to generate Isotropic/Kinematic hardening (I/KH) material models on a 3GAHSS steel with 980 MPa minimum tensile strength. Systematic material model parametric studies and evaluations have been conducted. Case studies from full-scale industrial parts are provided and the predicted springback results are compared to the measured springback data. Key variables affecting the springback prediction accuracy are identified.

More and more advanced high strength steels (AHSS) such as dual phase steels and TRIP steels are implemented in automotive components due to their superior crash performance and vehicle weight reduction capabilities. Recent trends show increased applications of higher strength grades such as 780/800 MPa and 980/1000 MPa tensile strength for crash sensitive components to meet more stringent safety regulations in front crash, side impact and roll-over situations. Several issues related to AHSS stamping have been raised during implementation such as springback, stretch bending fracture with a small radius to thickness ratio, edge cracking, etc. It has been shown that the failure strains in the stretch bending fracture and edge cracking can be significantly lower than the predicted forming limits, and no failure criteria are currently available to predict these failures.

Tensile tests were performed on DP600 and DP780 dual-phase steels to determine the relative effects of bake-hardening on the static and dynamic material response. The quasi-static test variables were prestrain level, specimen orientation (longitudinal, transverse), and heat treatment (as-received, bake hardened). Dynamic tests were performed at rates ranging from 0.001/s to 500/s, with variables of prestrain level and heat treatment. Increases in the ultimate and yield strength for both DP600 and DP780 were mainly due to prestrain and strain rate effects. The bake-hardening effects varied with the material, amount of prestrain, and strain rate. Crush tests were also performed on DP780 tubes in the as-received and bake-hardened conditions at rates ranging from quasi-static up to 7250 mm/s. The energy absorption was similar regardless of the rate.

Springback is a major concern in stamping of advanced high strength steels (AHSS). The existing computer simulation technology has difficulty predicting this phenomenon accurately even though it is well developed for formability simulations. Great efforts made in recent years to improve springback predictions have achieved noticeable progress in the computational capability and accuracy. In this work, springback simulation studies are conducted using FEA software LS-DYNA®. Various parametric sensitivity studies are carried out and key variables affecting the springback prediction accuracy are identified. Recently developed simulation technologies in LS-DYNA® are implemented including dynamic effect minimization, smooth tool contact and newly developed nonlinear isotropic/kinematic hardening material models. Case studies on lab-scale and full-scale industrial parts are provided and the predicted springback results are compared to the experimental data.

Edge cracking is one of the major formability concerns in advanced high strength steel (AHSS) stamping. Although finite element analysis (FEA) together with the Forming Limit Diagram has been widely used, it has not effectively predicted edge cracking. Primary problems in developing a methodology to insure that parts are safe from edge cracking are the lack of an effective failure criterion and a simple and accurate measurement method that is not only usable in both die tryout and production but also can be verified by finite element analysis. The intent of this study is to develop a methodology to ensure that parts with internal cutouts, such as a body side panel can be produced without edge cracking. During tryout and production, edge cracking has traditionally been detected by visual examination, but this approach is not adequate for ensuring freedom from edge cracking.

Advanced high strength steels (AHSS), such as dual phase (DP) and transformation induced plasticity (TRIP) steels, have been used successfully for making light weight vehicles and their usage is growing. Now, the automotive industry is expanding the use of AHSS to higher strength levels for further mass reduction. In a 2003 SAE paper, the material and formability characteristics for such steels were presented for steel grades of DP980, high yield type DP780 (780YM), low yield type DP780 (780YL), TRIP780, and TRIP590. In this study, experiments were conducted to assess the formability of these high strength steels using a T-channel, which incorporates several different forming modes in automotive stamping. The feasibility of computer simulation technology for the formability analyses of AHSS is also addressed.

Dual Phase (DP) high strength steel is widely used in Europe and Japan for automotive component applications, and has recently drawn greater attention in the North American automotive industry for improving crash performance and reducing weight. In comparison with high-strength low-alloy (HSLA) steel grades with similar initial yield strength, DP steel has the following advantages: higher strain hardening, higher energy absorption, higher fatigue strength, higher bake hardenablility, and no yield point elongation. This paper compares the performance of DP and HSLA steel grades before, during, and after hydroforming. Computer simulation results show that DP steel demonstrates more uniform material flow during hydroforming, better crash performance and less wrinkling tendency.

Dent resistance is one of the major requirements for automotive body panel design. It depends on material strength, thickness, panel geometry/shape and outer and inner panel assembling. Due to the complexity of the problem, the verification of dent resistance of body panels is often done after the panels are formed and assembled. In this paper, a computer simulation technique was developed for dent resistance predictions, which can potentially be used in early design stages before panels are produced. Simulation techniques are discussed using explicit finite element method (FEA) for forming simulation and implicit FEA for denting simulation. A lab stretch dome panel is used to demonstrate the feasibility of computer simulation for dent resistance prediction. The stretch dome panel, with double curvature geometry, is formed to 2% biaxial strain and then subjected to several incremental static loads until 0.2 mm dent depth is reached.

A typical forming operation of chassis components (control arms, cross members, etc.) often involves edge stretching and/or hole expansion. As a result, the edge split is a common forming failure mode. To overcome this problem, Japanese and European automakers use stretch flange high strength (SFHS) steel due to its high strength and excellent edge stretch capability. Recently, SFHS steel has gained greater attention in North America and is currently being used for upper and lower control arm applications. This paper includes a discussion on general edge stretch issues in forming operations, including material data that demonstrate the higher stretch limit of SFHS steel as compared to other high strength steels. In a case study, SFHS steel is applied to a control arm and finite element analysis (FEA) is conducted to evaluate forming and structural performance.

A 2001 SAE paper et al. [1,2] compared the formability aspects of six different grades of galvanealed steel [IF (270E), C-Mn (440W-1), low C - high Mn (440W-2), HSLA440 (440R), HSLA590 (590R) and DP590 (590Y)]. This study has been expanded to evaluate five additional advanced galvanealed steel grades [Low yield type DP780 (780YL), High yield type DP780 (780YM), DP980 (980Y), TRIP590 (590T), and TRIP780 (780T)]. The study presents material properties, forming characteristics in several lab tests and spring back characteristics. The study provides the actual and relative performance of these eleven steels and conclusions on the advantages these grades provide in cost-effective and mass-effective solutions to the manufacturing and performance requirements of the automotive body.

Advanced high strength steels (AHSS) are increasingly used in automotive industry. A major issue for AHSS stamping is edge cracking. This failure mode is difficult to predict by conventional forming limit curve (FLC). The material edge stretchability is mainly evaluated using the hole expansion test. In this study, digital Image Correlation (DIC) is applied for strain measurement. DIC is a non-contact, full field, high accuracy and direct measurement technique that provides more detailed information for the evolution of strains on the sheet surface. Tests were conducted for five AHSS and nine cases. This paper will explain in detail the DIC technique and its results.

Today’s automotive industry is witnessing increasing applications of advanced high strength steels (AHSS) combined with innovative manufacturing techniques to satisfy fuel economy requirements of stringent environmental regulations. The integration of AHSS in novel automotive structure design has introduced huge advantages in mass reduction while maintaining their structural performances, yet several concerns have been raised for this relatively new family of steels. One of those concerns is their potentially high springback after forming, which can lead to geometrical deviation of the final product from its designed geometry and cause difficulties during assembly. From the perspective of accurate prediction, control and compensation of springback, further understanding on the effect of residual stress in AHSS parts is urged. In this work, the residual stress distribution in a 980GEN3 steel part after hydroforming is investigated via experimental and numerical approaches.

The front rail plays a very important role in vehicle crash. Trigger holes are commonly used to control frame crush mode due to their simple manufacturing process and flexibility for late changes in the product development phase. Therefore, a study, including CAE and testing, was conducted on a production front rail to understand the effects of trigger hole shape, size and orientation. The trigger hole location in the front rail also affects crash performance. Therefore, the effect of trigger hole location on front rail crash behavior was studied, and understanding these effects is the main objective of this study. A tapered front rail produced from 1.7 mm thick DP600 steel was used for the trigger hole location investigation. Front rails with different trigger spacing and sizes were tested using VIA sled test facility and the crash progress was simulated using a commercial code RADIOSS. The strain rate, welding and forming effects were incorporated in the front rail modeling.

Tubular hydroforming is being used extensively for manufacturing various automotive structural parts due to its weight reduction and cost saving potentials. The use of a thin wall advanced high strength steel (AHSS) tube offers great potential to further expand hydroforming applications to upper body components. In this study, numerical and experimental investigations are conducted on a free expansion hydroforming case using various AHSS thin wall tubes. The results are also compared with tubes made from conventional steels and different tubing processes. The appropriate use of the forming limit in hydroforming is also discussed. In numerical study, a new simulation method is developed and validated to handle tube material properties input. Good correlations to the experimental data have been obtained. The new method only requires the flat sheet stress–strain curves as the basic material property. Tube and weld properties are modeled as a pre-strained tubular blank.

Corner fill is a simple benchmark conceived to gain knowledge of tube hydroforming. In corner fill of tube hydroforming, an originally long round tube is positioned in a cylindrical die with square cross-section and expands under applied internal pressure to fill the corners of the die. In order to ensure burst of the tubes, the cross-sectional dimension of the square die is chosen to be greater than the outer diameter of the tube. A two-dimensional plane strain finite element model has been developed to study the tube behaviors under applied internal pressure. This model treats the corner fill process more realistically than shell elements models because thickness stress and distortions of a normal segment through the thickness of the tube can be simulated [Chen, 2004]. The calculated results of stress and strain and the change of tube geometry as functions of pressure are presented.

Advanced High Strength Steels (AHSS) along with innovative design and manufacturing processes are effective ways to improve crash energy management. Crash trigger hole is another technology which can been used on front rails for controlling crash buckling mode, avoiding crash mode instability and minimizing variations in crash mode due to imperfections in materials, part geometry, manufacturing, and assembly processes etc. In this study, prototyped crash columns with different trigger hole shapes, sizes and locations were physically tested in frontal crash impact tests. A corresponding crash computer simulation model was then created to perform the correlation study. The testing data, such as crash force-displacement curves and dynamic crash modes, were used to verify the FEA crash model and to study the trigger sensitivity and effects on front rail crash performance.

Advanced high strength steels (AHSS), such as dual phase (DP) and transformation induced plasticity (TRIP) steels, have been increasingly used in automotive industry. One of the major advantages of AHSS is the excellent crash energy absorption capability. In this study, crash performances were evaluated for four AHSS including DP980, DP780, TRIP780 (780T), and TRIP590 (590T). Axial crush and bending crush tests were performed to evaluate the material crush performance. High strain rate tension test results for those materials were also presented. FEA analyses with parameter sensitivity studies were conducted including strain rate sensitivity effect, part geometry effects, welding models and forming effects. Good correlations between simulation and experimental data were achieved.

Experimental procedures and results of a benchmark test for springback are reported and a complete suite of obtained data is provided for the validation of forming and springback simulation software. The test is usually referred as the Slit-Ring test where a cylindrical cup is first formed by deep drawing and then a ring is cut from the mid-section of the cup. The opening of the ring upon slitting releases the residual stresses in the formed cup and provides a valuable set of easy-to-measure, easy-to-characterize springback data. The test represents a realistic deep draw stamping operation with stretching and bending deformation, and is highly repeatable in a laboratory environment. In this study, six different automotive materials are evaluated.