Search Results

Due to modern trends in the automotive industry, such as vehicle electrification, light-weighting, reduced NVH (Noise, Vibration and Harshness) packaging space, etc., it is desirable to have a low profile and light-weight acoustic material with multi-functionality. If one single layer of a thin acoustic material can provide comparable absorption and transmission loss to a multilayer treatment, it will benefit the industry by saving weight, packaging space and system cost. Acoustic absorption and sound transmission loss performance of a new dissipative material at reduced weight and thickness is introduced in this paper. The acoustic performance of the material was evaluated by using random incidence absorption and transmission loss as well as in-vehicle experiment. Further potential applications for this material have been identified using the Statistical Energy Analysis (SEA) method with panel leakage considered.

In this study, we investigated two aspects of a multi-layer, lightweight damping treatment. The first aspect studied was an equivalent material property estimate for a simplified finite element (FE) model. The simplified model is needed for computational efficiency, i.e. so that Tier 1 and OEM users can represent this complex, multi-layer treatment as a single, isotropic solid layer plus an aluminum constraining layer. Therefore, the use of this simplified FE model allows the multilayer treatment to be included in large body-in-white structural models. An equivalent material property was identified by first representing three unique layers (two adhesive layers plus a connecting standoff layer) by a single row of isotropic solid elements, then an optimization tool was used to determine the “best fit” for two properties including Young’s modulus and material loss factor.

Several methods for evaluating damping material performance are commonly used, such as Oberst beam test, power injection method and the long bar test. Among these test methods, the Oberst beam test method has been widely used in the automotive industry and elsewhere as a standard method, allowing for slight bar dimension differences. However, questions have arisen as to whether Oberst test results reflect real applications. Therefore, the long bar test method has been introduced and used in the aerospace industry for some time. In addition to the larger size bar in the long bar test, there are a few differences between Oberst (cantilever) and long bar test (center-driven) methods. In this paper, the differences between Oberst and long bar test methods were explored both experimentally and numerically using finite element analysis plus an analytical method. Furthermore, guidelines for a long bar test method are provided.

The aerospace industry has employed sandwich composite panels (stiff skins and lightweight cores) for over fifty years. It is a very efficient structure for rigidity per unit weight. For the automobile industry, we have developed novel thermoplastic composite panels that may be heated and shaped by compression molding or thermoforming with cycle times commensurate with automotive manufacturing line build rates. These panels are also readily recycled at the end of their service life. As vehicles become lighter to meet carbon dioxide emission targets, it becomes more challenging to maintain the same level of quietness in the vehicle interior. Panels with interconnected honeycomb cells and perforations in one skin have been developed to absorb specific noise frequencies. The absorption results from a combination and interaction of Helmholtz and quarter wave resonators.

In recent years, interest in microperforated panels (MPPs) has been growing in the automotive industry and elsewhere. Acoustic performance prediction is an important step toward understanding and designing MPPs. This paper outlines a start-to-finish procedure to predict the transfer impedance of a particular MPP based on its hole geometry and to further use this information in a simple plane wave application. A computational fluid dynamics (CFD) approach was used to calculate the impedance of the MPP and the results compared to impedance tube and flow resistance measurements. The transfer impedance results were then used to create a computationally efficient acoustic finite element (FE) model. The results of the acoustic FE model were also compared to impedance tube measurements.

In recent years several variants of lightweight multi-layered acoustic treatments have been used successfully in vehicles to replace conventional barrier-decoupler interior dash mats. The principle involved is to utilize increased acoustic absorption to offset the decrease in insertion loss from the reduced mass such that equivalent vehicle level performance can be achieved. Typical dual density fibrous constructions consist of a relatively dense cap layer on top of a lofted layer. The density and flow resistivity of these layers are tuned to optimize a balance of insertion loss and absorption performance. Generally these have been found to be very effective with the exception of dash mats with very high insertion loss requirements. This paper describes an alternative treatment which consists of a micro-perforated film top layer and fibrous decoupler layer.

Flat, constant thickness composites that consisted of a microperforated top layer plus a fibrous decoupler layer were tested for random absorption and transmission loss (TL) performance. The top, microperforated layer consisted of a relatively thick film that contained small, precise micro-perforations. For reference, top layers that consisted of a resistive scrim and an impervious film were also included in this study. Two fibrous materials of constant thickness were used for the decoupler layer between a steel panel and the top microperforated film. The composites' absorption and TL performance were also modeled using the well-known transfer matrix method. This method has been implemented in a commercially available statistical energy analysis (SEA) software package. A comparison of testing and modeling results showed reasonable agreement for absorption results and even better agreement for transmission loss and insertion loss results.

The damping effect that is observed when a fibrous acoustical treatment is applied to a thin metal panel typical of automotive structures has been modeled by using three independent techniques. In the first two methods the fibrous treatment was modeled by using the limp frame formulation proposed by Bolton et al., while the third method makes use of a general poro-elastic model based on the Biot theory. All three methods have been found to provide consistent predictions that are in excellent agreement with one another. An examination of the numerical results shows that the structural damping effect results primarily from the suppression of the nearfield acoustical motion within the fibrous treatment, that motion being closely coupled with the vibration of the base panel. The observed damping effect is similar in magnitude to that provided by constrained layer dampers having the same mass per unit area as the fibrous layer.