Search Results

Increasing demands on emissions reduction and efficiency encouraged a progressive introduction of cleaner combustion concepts. "Advanced" diesel combustions offer a high potential for simultaneous reduction of both NOx and soot within the engine through high inlet charge dilution and mixture homogenization. However, the potential benefits of these combustions in terms of emissions are counterbalanced by their high sensitivity to in-cylinder thermodynamic conditions. This sensitivity makes the engines require closed loop combustion control with real-time information about combustion quality. The parameter widely considered as the most important for the evaluation of the combustion quality in internal combustion engines is the cylinder pressure. However, this kind of measure involves an intrusive approach to the cylinder, expensive sensors and a special mounting process.

The aim of this paper is to analyze the effects of different driving styles and patterns onboard battery packs (BPs) supplying electric vehicles. The analysis is carried out by using real urban driving cycles, acquired through vehicle On Board Diagnostic Port (OBDP), and a Matlab-Simulink scaled BP model, in which lithium BP has been parametrized and validated through specific experimental tests. The results have been mainly focused on the evaluations of BP State of Health (SoH) and capacity fading decreasing during its lifetime at several critical conditions. In particular, these evaluations have allowed critical driving and environmental operative conditions to be identified and highlighted. The obtained results provide useful information for both producers of Battery Electric Vehicle (BEV) Energy Storage Systems (ESS) in the design stage, and for artificial intelligence driver support systems, mainly focused on extending overall vehicle life.

This work reports on the application of spectroscopic measurements coupled with data processing techniques in order to study, in terms of spectral emissions, the dynamic of the HCCI (Homogeneous charge compression ignition) combustion that occurs inside the combustion chamber of an optically accessible direct injection Diesel engine. A pre-processing of the recorded spectra is required for a correct analysis. The procedure of pre-processing consists of two main steps, that is: noise filtering with a technique based on the POD (Proper Orthogonal Decomposition); estimate and subtraction of the baseline. The analysis of the dynamics of the recorded spectra was carried out by the estimates of the synchronous and asynchronous 2D correlation spectra.

This paper deals with the combustion characteristics and exhaust emissions of a diesel engine fuelled with conventional diesel fuel and a biodiesel blend, in particular a 20% v/v concentration of rapeseed methyl ester (RME) mixed with diesel fuel. The investigation was carried out on a prototype three-cylinder engine with 1000 cc of displacement for quadricycle applications. The engine is equipped with a direct common-rail injection system that reaches a maximum pressure of 1400 bar. The engine was designed to comply with Euro 4 and BS IV exhaust emission regulations without a diesel particulate filter. Both in-cylinder pressure and rate of heat release traces were analyzed at different engine speeds and loads. Gaseous emissions were measured at the exhaust. A smoke meter was used to measure the particulate matter concentration. The sizing and the counting of the particles were performed by means of an engine exhaust particle sizer spectrometer.

A satisfactory answer to the future severe normative on emissions and to the market request for spark ignition engines seems to be the use of downsized engines for passenger cars. Downsizing permits the increase in engines power and torque without the increase in cylinder capacity. The downsizing benefits are evident at part loads; on the other hand, more work should be done to optimize boosted engines at higher and full load. To this goal, a detailed knowledge of the thermo-fluid dynamic processes that occur in the combustion chamber is fundamental. The aim of this paper is the experimental investigation of the effect of the fuel injection in the intake manifold on the combustion process and pollutant formation in a boosted spark ignition (SI) engine. The experiments were performed on a partially transparent single-cylinder port fuel injection (PFI) SI engine, equipped with a four-valve head and boost device.

Great efforts have been paid to improve engine efficiency as well as to reduce the pollutant emissions. The direct injection allows to improve the engine efficiency; on the other hand, the GDI combustion produces larger particle emissions. The properties of fuels play an important role both on engine performance and pollutant emissions. In particular, great attention was paid to the octane number. Oxygenated compounds allow increasing gasoline's octane number and play an important role in PM emission reduction. In this study was analyzed the effect of fuels with different RON and with ethanol and ethers content. The analysis was performed on a small GDI engine. Two operating conditions, representative of the typical EUDC cycle, were investigated. Both the engine performance and the exhaust emissions were evaluated. The gaseous emissions and particle concentration were measured at the exhaust by means of conventional instruments.

In this work, a boosted single-cylinder spark ignition port-fuel injection optical engine was used for the experimental activity. Firstly, it was equipped with a four-valve head of a commercial turbocharged multi-cylinder engine. Then a prototype engine head with flush installed intake valves was tested. The effect of the different head geometry was evaluated in closed intake valves fuel injection condition. High spatial resolution cycle-resolved digital imaging was used to characterise the flame propagation. Moreover, the presence of diffusion-controlled flames near the valves and on the cylinder walls was investigated. These flames induced the formation of unburned hydrocarbons and soot particles. The spatial distribution and temporal evolution of soot were evaluated by the two colour pyrometry. The prototype configuration showed higher combustion process efficiency than the standard one inducing a little increase in performance and a slight reduction in carbon oxides emissions.

Ethanol is the most promising alternative fuel for spark ignition (SI) engines, that is blended with gasoline, typically. Moreover, in the last years great attention is paid to the dual fueling, ethanol and gasoline are injected simultaneously. This paper aims to analyze the better methods, blending or dual fueling in order to best exploit the potential of ethanol in improving engine performance and reducing pollutant emissions. The experimental activity was carried out in a small displacement single cylinder engine, representative of 2-3 wheel vehicle engines or of 3-4 cylinder small displacement automotive engines. It was equipped with a prototype gasoline direct injection (GDI) head. The tests were carried out at 3000, 4000, and 5000 rpm full load. The investigated engine operating conditions are representative of the European homologation urban driving cycle.

The permanent aim of the automotive industry is the further improvement of the engine efficiency and the simultaneous pollutant emissions reduction. The aim of the study was the optimization of the gasoline combustion by means of a passive prechamber. This analysis allowed the improvement of the engine efficiency in lean-burn operation condition too. The investigation was carried out in a commercial small Spark Ignition (SI) engine fueled with gasoline and equipped with a proper designed passive prechamber. It was analyzed the effects of the prechamber on engine performance, Indicated Mean Effective Pressure, Heat Release Rate and Fuel Consumption were used. Gaseous emissions were measured as well. Particulate Mass, Number and Size Distributions were analyzed. Emissions samples were taken from the exhaust flow, just downstream of the valves. Four different engine speeds were investigated, namely 2000, 3000, 4000 and 5000 rpm.

The aim of this study is to investigate the combustion process and pollutant formation in a small compression ignition engine. The engine is a prototype for quadricycles. It was designed to comply with Euro 4 emission standard that is a future regulation for this type of vehicles. Two optical accesses for endoscopes were realized in the first cylinder to investigate the combustion process. Two-color pyrometry method was applied to combustion images in order to detect the flame temperature and the soot concentration. The engine ran with a biodiesel, the rapeseed methyl ester, and a conventional diesel fuel. Operating conditions at the engine speed of 2000 rpm at full and medium load were tested. NOx emissions were measured at exhaust. A smoke meter was used to determine the particulate matter concentration. The sizing and the counting of the particles were performed by means of an engine exhaust particle sizer spectrometer.

The growing concern about Greenhouse Gas (GHG) emissions led institutions to further reduce the limits on vehicle-related CO2 emissions. Therefore, car manufacturers are developing vehicles with low environmental impact, like Hybrid-Electric Vehicles (HEVs), which in the series architecture employ an Internal Combustion Engine (ICE) coupled with an electric generator for battery recharging, thus extending the range of a Battery Electric Vehicle (BEV). For this kind of application, small four-stroke Spark Ignition (SI) engines are preferred, as they are a proven and reliable solution to increase the driving range with very low environmental impact. In series hybrid-electric powertrains, the ICE is decoupled from the drive wheels, then it can operate in a steady-state high-efficiency working point, regardless of the power required by the mission profile. The benefits of lean combustion can be exploited to increase efficiency and reduce CO2 and NOx emissions.

The present paper describes the results of an experimental activity performed on a small diesel engine for quadricycles, a category of vehicles that is spreading in Europe and is recently spreading over Indian countries. The engine is a prototype three-cylinder with 1000 cc of displacement and it is equipped with a direct common-rail injection system that reaches a maximum pressure of 1400 bar. The engine was designed to comply with Euro 4 emission standard that is a future regulation for quadricycles. It is worth underlining that the engine can meet emission limits just with EGR system and a DOC, without DPF. Various diesel/RME blends were tested; pure diesel and biodiesel fuels were also used. The investigation was carried out at the engine speeds of 1400, 2000 and 3400 rpm and full load. Combustion characteristics of both blended and pure RME were analyzed by means of in-cylinder pressure and heat released histories.

This paper investigates abnormal combustion during the cranking phase of spark-ignition small engines, specifically the occurrence of backfire at the release of the starter motor during kickback. The research focusses on the influence of fuel composition, mainly in terms of ethanol percentage, on backfire occurrence. Interest in this abnormal combustion is growing due to the increased use of fuels with different chemical-physical properties with respect to gasoline. Moreover, this issue will become even more topical due to the implementation of simple control and fuel supply systems on low cost-engines, which are widely used in developing countries. Experimentation was carried out in an optically accessible engine derived from a 4-stroke spark ignition engine for two-wheel vehicles. The test bench was instrumented and adapted in order to simulate the engine conditions that lead to anomalous ignition in the intake duct (backfire) during the reverse rotation of the engine (kickback).

In this paper, the effect of the oxygen addition on engine performance and exhaust emissions was investigated. The experimental study was carried out in a small single-cylinder PFI SI four-stroke engine. The addition of the 5% vol and 10% vol of oxygen was performed in the intake duct. Typical urban driving operating conditions were investigated. The engine emissions were characterized by means of gaseous analyzers and a smokemeter. Particle size distribution function was measured in the size range from 5.6 to 560 nm by means of an Engine Exhaust Particle Sizer (EEPS). An improvement in terms of engine power output, without BSFC penalty, and HC emissions with oxygen addition was observed at all the investigated operating conditions. On the other hand, NOx and PM emissions increase.

The use of direct injection (DI) engines allows a more precise control of the air-fuel ratio, an improvement of fuel economy, and a reduction of exhaust emissions thanks to the ultra-lean combustion due to the charge stratification. These effects can be partially obtained also with an optimized Air Direct Injection that permits to increase the turbulence at low speed and load increasing the combustion stability especially in lean condition. In this paper, a gasoline PFI (named G-PFI), gasoline PFI-methane DI dual fuel (named G-MDF) lean combustion were analyzed. The G-MDF configuration was also compared with a gasoline PFI - air DI (named G-A) configuration in order to distinguish the chemical effect of methane from the direct injection physical effect. The tests were carried out in a small displacement PFI/DI SI engine. The experimental investigation was carried out in a transparent small single-cylinder, spark ignition four-stroke engine.

The aim of the paper is the comparison of the performance, gaseous and particle emissions from different injection configurations and fuels. The engine was operated in port fuel injection (PFI), direct injection (DI) and dual fuel (DF). For DF, ethanol DI-gasoline PFI and gasoline DI-gasoline PFI strategies were performed to discern the effect of injection strategy from the effect of the fuel. The experimental activity was carried out in a small displacement single cylinder engine, representative of 2-3 wheel vehicle engines or of 3-4 cylinder small displacement automotive engines. It was equipped with a prototype gasoline direct injection (GDI) head. The tests were carried out at 3000 rpm, 4000 rpm and 5000 rpm full load. The investigated engine operating conditions are representative of the homologation urban driving cycle. The gaseous and particle emissions were measured at the exhaust by means of a gas analyzer and a smoke meter.

The constant aim of the automotive industry is the further improvement of engine efficiency and the simultaneous reduction of the exhaust emissions. In order to optimize the internal combustion engines it is necessary to further improve the basic knowledge of the thermo-fluid dynamic phenomena occurring during the combustion process. In this context, the application of optical diagnostic techniques permits a deep insight into the fundamental processes such as flow development, fuel injection, and combustion process. In this paper the analysis of the combustion process of gaseous fuel ignited by the plasma jets coming from a prechamber was performed. The investigation was carried out in an optically accessible small Direct Injection Spark-Ignition (DI SI) engine fueled with Methane. The ignition was obtained with a properly designed fueled prechamber prototype.

In this paper the methane-gasoline dual fuel combustion was investigated. Gasoline was injected in the intake manifold (PFI fuel), while methane was injected in the combustion chamber (DI fuel), in order to reproduce a stratified combustion. The combustion process and the related engine performance and pollutant emissions were analyzed. The measurements were carried out in an optically accessible small single-cylinder four-stroke engine. It was equipped with the cylinder head of a commercial 250 cc engine representative of the most popular two-wheel vehicles in Europe. Optical measurements were performed to analyze the combustion process with high spatial and temporal resolution. In particular, optical techniques based on 2D-digital imaging were used to follow the flame front propagation and the soot and temperature concentration in the combustion chamber.

The aim of the present work is to provide further guidance into better understanding the production mechanisms of soot emissions in Spark-Ignition SI engines fueled with compressed natural gas. In particular, extensive experimental investigations were designed with the aim to isolate the contribution of the fuel from that of lubricant oil to particle emissions. This because the common thought is that particulate emerging from the engine derives mainly from fuel, otherwise the contribute of lubricant oil cannot be neglected or underestimated, especially when the fuel itself produces low levels of soot emissions, such as in the case of premixed natural gas. The fuel-derived contribution was studied by analyzing the influence that natural gas composition has on soot emitted from a single cylinder Spark-Ignition (SI) engine. To achieve this purpose, methane/propane mixtures were realized and injected into the intake manifold of a Single-Cylinder SI engine.

The management of multiple injections in compression ignition (CI) engines is one of the most common ways to increase engine performance by avoiding hardware modifications and after-treatment systems. Great attention is given to the profile of the injection rate since it controls the fuel delivery in the cylinder. The Injection Rate Shaping (IRS) is a technique that aims to manage the quantity of injected fuel during the injection process via a proper definition of the injection timing (injection duration and dwell time). In particular, it consists in closer and centered injection events and in a split main injection with a very small dwell time. From the experimental point of view, the performance of an IRS strategy has been studied in an optical CI engine. In particular, liquid and vapor phases of the injected fuel have been acquired via visible and infrared imaging, respectively. Injection parameters, like penetration and cone angle have been determined and analyzed.