Search Results

Dimethyl ether (DME) is a promising alternative fuel for compression ignition (CI) engines. DME features good auto ignition characteristics and soot-free combustion. In order to develop an injection system suitable for DME, it is necessary to understand its fuel properties. Sound speed is an important fuel property that affects the injection characteristics. However, the measurement data under high-pressures corresponding to those in fuel injection systems are lacking. The critical temperature of DME is lower than that of diesel fuel, and is close to the injection condition. It is important to understand the behavior of the sound speed around the critical point, since the sound speed at critical point is extremely low. In this study, sound speed in DME in a wide pressure and temperature range of 1 MPa to 80 MPa, 298.15 K to 413.15 K, including the vicinity of the critical point, was measured. The sound speed in DME decreases as either the pressure falls or the temperature rises.

DiMethyl Ether (DME) has been known to be an outstanding fuel for combustion in diesel cycle engines for nearly twenty years. DME has a vapour pressure of approximately 0.5MPa at ambient temperature (293K), thus it requires pressurized fuel systems to keep it in liquid state which are similar to those for Liquefied Petroleum Gas (mixtures of propane and butane). The high vapour pressure of DME permits the possibility to optimize the fuel injection characteristic of direct injection diesel engines in order to achieve a fast evaporation and mixing with the charged gas in the combustion chamber, even at moderate fuel injection pressures. To understand the interrelation between the fuel flow inside the nozzle spray holes tests were carried out using 2D optically accessed nozzles coupled with modelling approaches for the fuel flow, cavitation, evaporation and the gas dynamics of 2-phase (liquid and gas) flows.

For nearly twenty years, DiMethyl Ether has been known to be an outstanding fuel for combustion in diesel cycle engines. Not only does it have a high Cetane number, it burns absolutely soot free and produces lower NOx exhaust emissions than the equivalent diesel. However, the physical properties of DME such as its low viscosity, lubricity and bulk modulus have negative effects for the fuel injection system, which have both limited the achievable injection pressures to about 500 bar and DME's introduction into the market. To overcome some of these effects, a common rail fuel injection system was adapted to operate with DME and produce injection pressures of up to 1000 bar. To understand the effect of the high injection pressure, tests were carried out using 2D optically accessed nozzles. This allowed the impact of the high vapour pressure of DME on the onset of cavitation in the nozzle hole to be assessed and improve the flow characteristics.

Dimethyl ether (DME) holds promise as an alternative to diesel fuel. However, its physical properties are not similar to those of conventional diesel fuel. The P-V, bulk modulus and viscosity of DME are derived as a function of temperature and pressure. As a result, the Weber and Reynolds number of DME is very large as compared with that of diesel fuel. So, the spray characteristics of DME are not those of a liquid spray but similar to those of gas spray. The spray formation is strongly affected by the fuel flow in the nozzle. The Computational Fluid Dynamics (CFD) and experiments are examined to analyze the fuel flow in the nozzle. The DME physical properties make some difference to the flow in the nozzle, in comparison with those of diesel. As a CFD result, cavitation in the injection nozzle is more frequent with DME than with diesel oil. From experimental results, the temperature in the nozzle sac is higher with DME than with diesel oil.

Dimethyl ether(DME) is a promising new alternative fuel not only diesel fuel but also power generation, fuel cell and city gas. However, the physical properties are not similar to those of conventional diesel fuel. The P-v, bulk modulus and viscosity of DME are derived as a function of temperature and pressure. As a Result, the Weber and Reynolds number of DME is very large as compared with that of diesel fuel. So, the spray characteristics of DME is not the liquid spray but similar to that of gas spray. The spray formation is strongly affected by the fuel flow in the nozzle. The Computational Fluid Dynamics (CFD) and the experiments are examined to analyze the fuel flow in the nozzle. The DME physical properties make some difference of the flow in the nozzle, comparing with those of diesel. As a CFD result, cavitation in the injection nozzle is more frequent with DME than with diesel oil.

This paper will focus on fuel flow analysis in nozzles, in particular, in the injection hole, a key component of Fuel Injection Equipment(FIE). Optimum controlled flow in the hole improves flow efficiency and atomization. To meet the emission regulations which will be introduced from the end of '90's to the 21st century, Diesel Engines require FIE to produce higher injection pressure which creates better atomization and higher utilization of air. But higher injection pressure results in increased pump driving torque, larger pump size and higher cost. We have studied the improvement in fuel flow characteristics of the nozzle, using an enlarged flow model and the theoretical analysis method. As a result, we have found that the cavitation, which occurs at the inlet of the hole, is affected by the configuration of the sac hole and injection hole. And, furthermore, the cavitation has a direct effect on the contraction and its recovery flow.