Search Results

The authors investigated the reasons of how a preignition occurs in a highly boosted gasoline engine. Based on the authors' experimental results, theoretical investigations on the processes of how a particle of oil or solid comes out into the cylinder and how a preignition occurs from the particle. As a result, many factors, such as the in-cylinder temperature, the pressure, the equivalence ratio and the component of additives in the lubricating oil were found to affect the processes. Especially, CaCO3 included in an oil as an additive may be changed to CaO by heating during the expansion and exhaust strokes. Thereafter, CaO will be converted into CaCO3 again by absorbing CO2 during the intake and compression strokes. As this change is an exothermic reaction, the temperature of CaCO3 particle increases over 1000K of the chemical equilibrium temperature determined by the CO2 partial pressure.

LSPI is an important issue to enable and enhance the effect of downsizing in SI engines. Experimental work was carried out by using 4 cylinder turbocharged gasoline engine, attaching the extra supercharger to get a higher boost pressure. Many parameters of driving condition, engine specification and lubricants were studied and some of them were extracted as the major items which affect the possibility of LSPI. Coolant temperature and Calcium (Ca) additive to lubricant had strong effect on the frequency of LSPI. Combustion strategy of strong miller cycle and LPEGR were also studied and compared in very high BMEP condition. Finally IMEPg of 3MPa at 1500rpm was achieved by using a single cylinder test engine equipped with 2-stage mechanically supercharged intake system.

The variable valve lift and duration (in the following: VVLD) devices, some have been mass-produced already in the world, are necessary to be assembled with the variable cam phaser (in the following: VCP) to optimize open and close valve timing. On the other hand, with the variable valve phase and lift (in the following: VVPL) mechanism, the valve event is advanced with decreasing the valve lift and duration. Hence, no additional VCP is required when using the VVPL for throttle-less operation. A new VVPL has been developed as a mechanical, swing-cam actuation mechanism. The mechanisms of the conventional production VVLD devices are investigated and the functional analysis of the possible mechanisms is carried out to identify and design a simple mechanism for the new VVPL. The designed VVPL system is capable of continuously varying the valve lift from 0 mm to 10 mm, with the higher valve lift for any of the given duration.

To find an ignition and combustion control strategy in a gasoline-fueled HCCI engine equipped with the BlowDown SuperCharging (BDSC) system which is previously proposed by the authors, a one-dimensional HCCI engine cycle simulator capable of predicting the ignition and heat release of HCCI combustion was developed. The ignition and the combustion models based on Livengood-Wu integral and Wiebe function were implemented in the simulator. The predictive accuracy of the developed simulator in the combustion timing, combustion duration and heat release rate was validated by comparing to experimental results. Using the developed simulator, the control strategy for the engine operating mode switching between HCCI and SI combustion was explored with focus attention on transient behaviors of air-fuel ratio, A/F, and gas-fuel ratio, G/F.

To extend the operating range of a gasoline HCCI engine, the blowdown supercharging (BDSC) system and the EGR guide were developed and experimentally examined. The concepts of these techniques are to obtain a large amount of dilution gas and to generate a strong in-cylinder thermal stratification without an external supercharger for extending the upper load limit of HCCI operation whilst keeping dP/dθmax and NOx emissions low. Also, to attain stable HCCI operation using the BDSC system with wide operating conditions, the valve actuation strategy in which the amount of dilution gas is smaller at lower load and larger at higher load was proposed. Additionally to achieve multi-cylinder HCCI operation with wide operating range, the secondary air injection system was developed to reduce cylinder-to-cylinder variation in ignition timing. As a result, the acceptable HCCI operation could be achieved with wide operating range, from IMEP of 135 kPa to 580 kPa.

The objective of this study is to develop a practical technique to achieve HCCI operation with wide operation range. To attain this objective, the authors previously proposed the blowdown supercharge (BDSC) system and demonstrated the potential of the BDSC system to extend the high load HCCI operational limit. In this study, experimental works were conducted with focusing on improvement of combustion stability at low load operation and the reduction in cylinder to cylinder variation in ignition timing of multi-cylinder HCCI operation using the BDSC system. The experiments were conducted using a slightly modified production four-cylinder gasoline engine with compression ratio of about 12 at constant engine speed of 1500 rpm. The test fuel used was commercial gasoline which has RON of 91. To improve combustion stability at low load operation, the valve actuation strategy for the BDSC system was newly proposed and experimentally examined.

In order to extend the HCCI high load operational limit, the effects of the distributions of temperature and fuel concentration on pressure rise rate (dP/dθ) were investigated through theoretical and experimental methods. The Blow-Down Super Charge (BDSC) and the EGR guide parts are employed simultaneously to enhance thermal stratification inside the cylinder. And also, to control the distribution of fuel concentration, direct fuel injection system was used. As a first step, the effect of spatial temperature distribution on maximum pressure rise rate (dP/dθmax) was investigated. The influence of the EGR guide parts on the temperature distribution was investigated using 3-D numerical simulation. Simulation results showed that the temperature difference between high temperature zone and low temperature zone increased by using EGR guide parts together with the BDSC system.

The objective of this study is to extend the high load operation limit of a gasoline HCCI engine. A new system extending the high load HCCI operation limit was proposed, and the performance of the system was experimentally demonstrated. The proposed system consists of two new techniques. The first one is the “Blow-down super charging (BDSC) system”, in which, EGR gas can be super charged into a cylinder during the early stage of compression stroke by using the exhaust blow-down pressure wave from another cylinder phased 360 degrees later/earlier in the firing order. The other one is “EGR guide” for generating a large thermal stratification inside the cylinder to reduce the rate of in-cylinder pressure rise (dP/dθ) at high load HCCI operation. The EGR guides consist of a half-circular part attached on the edge of the exhaust ports and the piston head which has a protuberant surface to control the mixing between hot EGR gas and intake air-fuel mixture.

Research into HCCI technology has been based on gasoline or diesel engines, using a large amount of EGR and supercharging(1). In this paper, a new method is introduced, which realizes heavy internal EGR and supercharging simultaneously using exhaust blow down pressure without a super charger. A four cylinder HCCI gasoline engine is initially introduced with a BDSCac (Blow Down Super-Charging by accumulation) system which achieves a large amount of EGR and simultaneously supercharging without a supercharger. This is brought about by accumulating the exhaust blow down pressure in one of two separate exhaust systems, and its characteristics are explained. Further research has been made into a new method to achieve a similar effect as BDSCac by using a common exhaust system and a simple mechanical cam-driven variable valve actuation system. The system is called BDSCpw (Blow Down Super-Charging by pressure wave).

In order to study alternate methods of Air Fuel ratio (A/F) perturbation for maximizing three-way catalyst conversion efficiency, two methods for measuring the Oxygen Storage Capacity (OSC) of Catalyst were developed on an engine test bench. The first is to measure just the break-through Perturbing Oxygen Quantity (POQ, which is defined as the product of A/F amplitude, perturbation period and gas flow), and the second is to measure the response delay of the rear A/F sensor, which has been improved to be very similar to the former. Then, the OSC values of many catalysts were investigated with different perturbation parameters. The results show that OSC would not be affected by amplitude, period of perturbation and gas flow, and that the best conversion efficiency is obtained when the value of POQ is about 1/2 of the value for OSC. These results suggest that the best way to control perturbation is to keep POQ at 1/2 of OSC by setting perturbation parameters.

Reduction of transmission error by gear tooth profile optimization and tuning of gear resonance modes are known as effective methods for gear noise reduction. This paper concentrates on structuring a process for reducing gear noise using the latter method. The procedure comprises a study of gear noise mechanism from transmission error to radiation noise, an application of Steyer's method in gear frequency analysis and implementation of an invented device called “noise reduction ring”. This inexpensive and practical ring reduces gear noise drastically by 10dB, which is predicted by the simulation and verified by the experiment.