Search Results

In the present paper, results of an experimental investigation carried out in a modern Diesel engine running at different operating conditions and fuelled with commercial diesel and n-butanol-diesel blend are reported. The investigation was focused on the management of injection strategy and combustion timing (CA50) exploring the effect of intake oxygen concentration and boost pressure on engine out emissions. The aim of the paper was to compare, with respect to commercial diesel, the effects of a fuel blend with a lower cetane number and higher volatility on performance and engine out emissions. Engine tests, with baseline diesel and a blend made by the baseline low sulphur diesel with 20% in volume of n-butanol (B20), were performed comparing engine out gaseous, smoke emissions and combustion efficiency. The investigation was performed on a turbocharged, water cooled, DI diesel engine, equipped with a common rail injection system.

This paper reports results of an experimental investigation performed on a commercial diesel engine supplied with fuel blends having low cetane number to attain a simultaneous reduction in NOx and smoke emissions. Blends of 20% and 40% of n-butanol in conventional diesel fuel have been tested, comparing engine performance and emissions to diesel ones. Taking advantage of the fuel blend higher resistance to auto ignition, it was possible to extend the range in which a premixed combustion is achieved. This allowed to match the goal of a significant reduction in emissions without important penalties in fuel consumption. The experimental activity was carried on a turbocharged, water cooled, 4 cylinder common rail DI diesel engine. The engine equipment included an exhaust gas recirculation system controlled by an external driver, a piezo-quartz pressure transducer to detect the in-cylinder pressure signal and a current probe to acquire the energizing current to the injector.

Optical imaging and UV-visible detection of in-cylinder combustion phenomena were made in a single cylinder optically accessed high swirl multi-jets compression ignition engine operating with two different fuels and two EGR levels. A commercial diesel fuel and a lighter fuel blend of diesel (80%) and gasoline (20%), named G20, were tested for two injection pressures (70 and 140 MPa) and injection timings in the range 11 CAD BTDC to 5 CAD ATDC. The blend G20 has a lower cetane number, is more volatile and more resistant to the auto-ignition than diesel yielding an effect on the ignition delay and on the combustion performance. Instantaneous fuel injection rate, in-cylinder combustion pressure, NOx and smoke engine out emissions were measured. Taking into account the particular configuration of the engine, the efficiency was estimated by determining the area under the working engine cycle.

This paper reports results of an experimental investigation to demonstrate the potential to employ blends of fuels having low cetane numbers that can provide high resistance to auto-ignition to reduce simultaneously NOx and smoke. Because of the higher resistance to auto-ignition, blends of diesel and gasoline at different volume fraction may provide more time for the mixture preparation by increasing the ignition delay. The result produces the potential to operate under partially premixed low temperature combustion with lower levels of EGR without excessive penalties on fuel efficiency. In addition to the diesel fuel, the tested blends were mixed by the baseline diesel with 20% and 40% of commercial EURO IV 98 octane gasoline by volume, denoted G20 and G40. The experimental activity has been performed on a turbocharged, water cooled, DI diesel engine, equipped with a common rail injection system.

The addition of alcohol to conventional hydrocarbon fuels for a spark-ignition engine can increase the fuel octane rating and the power for a given engine displacement and compression ratio. In this work, the influence of butanol addition to gasoline was investigated. The experiments were performed in an optical ported fuel injection single-cylinder SI engine with an external boosting device. The engine was equipped with the head of a commercial SI turbocharged engine having the same geometrical specifications (bore, stroke and compression ratio). The effect of a blend of 20% of n-butanol and 80% of gasoline (BU20) on in-cylinder combustion process was investigated by cycle-resolved visualization. The engine worked at low speed, medium boosting and wide open throttle. Changes in spark timing and fuel injection phasing were considered. Comparisons between the flame luminosity and the combustion pressure data were performed.

To meet the future stringent emission standards, innovative diesel engine technology, exhaust gas after-treatment, and clean alternative fuels are required. Oxygenated fuels have showed a tendency to decrease internal combustion engine emissions. In the same time, advanced fuel injection modes can promote a further reduction of the pollutants at the exhaust without penalty for the combustion efficiency. One of the more interesting solutions is provided by the premixed low temperature combustion (LTC) mechanism jointly to lower-cetane, higher-volatility fuels. In this paper, to understand the role played by these factors on soot formation, cycle resolved visualization, UV-visible optical imaging and visible chemiluminescence were applied in an optically accessed high swirl multi-jets compression ignition engine. Combustion tests were carried out using three fuels: commercial diesel, a blend of 80% diesel with 20% gasoline (G20) and a blend of 80% diesel with 20% n-butanol (BU20).

In this paper, a Low Temperature Premixed Combustion (LTPC) was investigated employing a four cylinder D.I. common rail Diesel engine, used for passenger cars on the European market. Experiments were carried out setting the engine speed at 2500 rpm with a fuel amount of 26 mg/str to realize an operating condition close to the point of NEDC at 0.8 MPa of BMEP. The experimental approach was the management of the start of injection, injection pressure and EGR rates as a method to control NOx and soot production. The investigation was first carried out testing engine performances and emissions as set from the commercial engine map. Afterward, engine tests were carried out exploring performances, gaseous and smoke emissions at late start of combustion [10 to 17.5 cad ATDC], injection pressures from 80 to 120 MPa and EGR rates up to 50%.

The paper illustrates the interdisciplinary matching of different numerical and experimental techniques, aimed to characterize the performances, emissions and combustion noise radiated from a small-size DI diesel engine. The main objective is the development of proper models to be included within an optimization procedure, able to define an optimal injection strategy for a common-rail engine. The injection strategy is selected to simultaneously reduce the fuel consumption, the pollutant emissions and the combustion noise. The engine considered is a naturally aspirated, four strokes, two valves, single-cylinder engine (505 cm3 displacement), to be equipped with a prototype common-rail fuel injection system. A preliminary experimental investigation is carried out on the above engine, equipped, however, with a standard mechanical injection system (base engine).

The effect of ammoniac deoxidizing agent (Urea) on the reduction of NOx produced in the Diesel engine was investigated numerically. Urea desolved in water was directly injected into the engine cylinder during the expansion stroke. The NOx deoxidizing process was described using a simplified chemical kinetic model coupled with the comprehensive kinetics of Diesel oil surrogate combustion. If the technology of DWI (Direct Water Injection) with the later injection timing is supposed to be used, the deoxidizing reactants could be delivered in a controlled amount directly into the flame plume zones, where NOx are forming. Numerical simulations for the Isotta Fraschini DI Diesel engine are carried out using the KIVA-3V code, modified to account for the “co-fuel” injection and reaction with combustion products. The results showed that the amount of NOx could be substantially reduced up to 80% with the injection timing and the fraction of Urea in the solution optimized.

The main objective of the present paper is the application of a detailed kinetic model to study diesel combustion in an optical accessible engine equipped with a common rail injection system. Three different injection schedules made of one to three consecutive injections are considered from both the numerical and the experimental point of view. The numerical model is assessed in such a way to assure its portability with respect to changing injection strategies. The employed detailed kinetic mechanism consists of 305 reactions involving 70 species and is included in the KIVA-3V code. The considered fuel has the liquid phase properties of the diesel oil, the vapor phase properties of C14H28. It is subsequently decomposed into n-heptane and toluene. The chemical solver is based on the use of the reference species technique and on the Partially Stirred Reactor (PaSR) hypothesis. These allow maintaining the computational cost within acceptable limits.

The paper summarizes the activities related to the characterization of the noise sources and related sound emission levels emitted by a single cylinder diesel engine. A deep analysis is carried out aiming to clearly define the various noise sources, through the employment of numerical and experimental techniques. In particular, an intensimetric analysis is carried out to define a bi-dimensional noise level map around the engine. In addition, the gasdynamic noise, at the different engine speeds, is measured through a microphone mounted near the intake and exhaust mouth. Contemporarily to the experimental activity, a theoretical one dimensional simulation of the whole engine, is also carried out. The presented one-dimensional analysis is able to characterize the wave propagation phenomena in the external ducts and provide the estimation of both engine performance and gasdynamic noise emission too.

This paper illustrates the results of an experimental characterization of a high pressure diesel spray injected by a common rail (CR) injection system both under non-evaporative and evaporative conditions. Tests have been made injecting the fuel with a single hole injector having a diameter of 0.18 mm with L/D=5.56. The fuel has been sprayed at 60, 90 and 120 MPa, with an ambient pressure ranging between 1.2 to 5.0 MPa. The spray evolution has been investigated, by the Mie scattering technique, illuminating the fuel jet and acquiring single shot images by a CCD camera. Tests under non-evaporative conditions have been carried out in an optically accessible high pressure vessel filled with inert gas (N2) at diesel-like density conditions. The instantaneous fuel injection rate, obtained with a time resolution of 10 microseconds, has been also evaluated by an AVL Fuel Meter working on the Bosch Tube principle.

The paper aims at providing information about the spray structure and its evolution within the combustion chamber of a heavy duty direct injection (HDDI) diesel engine. The spray penetration is investigated, firstly under quiescent conditions, injecting the fuel in a vessel under ambient temperature and controlled back pressure by both numerical and experimental analyses using the STAR-CD code and the imaging technique, respectively. Experimental results of fuel injection rate, fuel penetration, and spray cone angle are used as initial conditions to the code and for the comparison of predictions. The experimental investigation is carried out using a mechanical injection pump equipped by the heavy duty eight cylinder engine. Only one of its plungers has been activated and the fuel is discharged through a seven holes mechanical injector, 0.40 mm in diameter.

A customised version of FIRE™ code is chosen to simulate the spray injected into a controlled environment by means of a Common Rail system driven via a Programmable Electronic Control Unit. Numerical results are compared to experimental data collected under various operating conditions, namely varying the injection pressure up to 120 MPa, and the gas back-pressure between 0.1 and 5.0 MPa. Non-evaporating conditions are considered. The employed optically accessible test chamber allows to light the spray with a flash lamp or a pulsed laser sheet, generated on the second harmonic of a Nd-YAG laser (532 nm, 12 ns in duration). Images are collected at different instants of time after the start of injection by means of a CCD camera. A digital image processing software is used to evaluate the major characteristics of the spray, as the penetration length and the cone angle. The injection flow rate is properly measured on a rate-of-injection flow bench for different injection strategies.

Comfort requirements, government regulations as well as consumer action groups are pressing the automotive industry to produce less noisy vehicles than in the past. These circumstances become more and more important for off-road and human operating machines forcing engine developers to investigate new and more effective control strategies of noise emissions. This paper concerns with the experimental vibro-acoustic analysis of a small (224 cc) single-cylinder direct-injection diesel engine used for agricultural and industrial applications as well as off road small vehicles. In order to evaluate the engine acoustic behaviour, experimental identification and localization of noise sources were performed at different speed and load engine conditions by several investigating tools. Within them, the intensity technique was chosen because of its peculiarities to be performed “in situ” without a specific anechoic test environment.

Spectroscopic measurement and high speed visualization were used in single cylinder, four-stroke DI diesel engine, optically accessible. It was equipped with a four valves head and fully flexible electronic controlled ‘Common Rail’ injection system. The effect of pilot and main injection on combustion process was evaluated. Mixing formation, autoignition and soot formation process were analyzed by broadband ultraviolet-visible flame emission spectroscopy and high-speed digital imaging. The autoignition phase occurred near the tip of the jet and was characterized by strong presence of OH radicals for both investigated conditions The presence of C2 and OH radicals strongly characterized CR diesel combustion process during soot formation and evolution. In particular, high presence of OH concentration for the whole process from the autoignition to the soot formation and successive phases contributes to lower soot levels.

The paper illustrates an experimental and numerical investigation of the flow generated by an intake port model for a heavy duty direct injection (HDDI) Diesel engine. Tests were carried out on a steady state air flow test rig to evaluate the global fluid-dynamic efficiency of the intake system, made by a swirled and a directed port, in terms of mass flow rate, flow coefficients and swirl number. In addition, because the global coefficients are not able to give flow details, the Laser Doppler Anemometry (LDA) technique was applied to obtain the local distribution of the air velocity within a test cylinder. The steady state air flow rig, made by a blower and the intake port model mounted on a plexiglas cylinder with optical accesses, was assembled to supply the actual intake flow rate of the engine, setting the pressure drop across the intake ports atûP=300 and 500 mm of H2O.

Polychromatic extinction and chemiluminescence techniques, from ultraviolet to visible, were applied in an optical diesel engine, in order to analyze the temporal and spatial evolution of a high pressure fuel jet interacting with a swirling air motion. A fully flexible Common Rail fuel injection system equipped with a single hole nozzle was used. The experiments were performed at fixed engine speed and air/fuel ratio for three injection strategies. The first one consisted of a main injection to compare with those operating at low pressure injection. The other ones were based on a pilot and main injections, typical of current direct injection diesel engines, with different dwell time. A detailed investigation of the mixture formation process inside the combustion chamber during the ignition delay time was performed. The liquid and vapor fuel distribution in the combustion chamber was obtained analyzing the polychromatic extinction spectra.

Conventional methods to measure gas concentrations and, in particular, NO are typically based on sampling by valve, sample treatment and subsequent analysis. These methods suffer low spatial and temporal resolution. The introduction of high energy lasers in combination with fast detection systems allowed to detect the NO distribution inside optically accessible Diesel engines. In this paper, a high spatial and temporal resolution in-situ technique based on ultraviolet - visible absorption spectroscopy is proposed. The characterization of the combustion process by the detection of gaseous compounds from the start of combustion until the exhaust phase was performed. In particular, this technique allows the simultaneous detection of NO and OH absolute concentrations inside an optically accessible Diesel combustion chamber.

This paper explores the possibility to extend the low-temperature combustion concept developed for low load conditions to medium load conditions of HSDI DI Diesel engines. The aim is to understand which is the limit of conventional Diesel combustion towards smoke-lees and NOx-less conditions. The present research is based on numerical simulations performed by using the Kiva-3 code updated with physical sub-models. The combined influence of EGR cooling and EGR rate on combustion characteristics and emission formation is analyzed. Then, possible improvements to mixture formation are discussed with particularly emphasis on the use of multiple injection. The calculations show that smoke-less conditions by low-temperature combustion cannot be achieved at medium load and therefore a great role is played by mixture formation.