Search Results

The paper describes a zero-dimensional crank angle resolved combustion model which was developed for the analysis and prediction of combustion in compression ignition (CI) engines. The model relies on the multi zone combustion model (MZCM) approach of Hiroyasu. The main sub-models were taken from literature and extended with additional features described in this paper. A special procedure described in a previous paper is used to identify the mechanisms of the combustion process on the basis of the measured cylinder pressure trace. Based on the identified mechanisms the present work concentrates on the analysis of the causal effects that predominantly control the combustion process and the formation of NOx and Soot. The focus lies on the changes of the thermodynamic states and the composition of the reaction zones caused by different emission control strategies.

In order to meet the Euro V heavy-duty diesel emission standard legislation limits, a diesel engine can be optimized by internal means to give low particulate emissions and lower fuel consumption. These modifications of the engine lead inevitably to higher NOx emissions due to the NOx/PM trade off. An efficient Urea SCR after-treatment system is then able to reduce the higher NOx emission to below the Euro V 2.0g/kWh legislation limit. This paper presents tests made on a PM optimized 12 liter heavy-duty diesel engine together with a urea SCR after-treatment system. The optimized engine had engine out particulate emissions of about 0.04 g/kWh and NOx emissions of 9 g/kWh for the ESC and 8,5 g/kWh for the ETC. The fuel consumption of the optimized engine was 194 g/kWh for the ESC and 198 g/kWh for the ETC as compared to state of the art Euro III engines of typically 210 g/kWh for the ESC, giving significant fuel savings of 7.5 %.

The internal combustion engines, and the heavy duty truck diesel engines in particular, are facing a severe challenge to cope with the upcoming stringent emission legislation world-wide. To comply with these low limits, engine internal measures must be complemented with exhaust gas aftertreatment systems with sophisticated electronic control. A reduction of NOx and particulate emission of more than 90% is required. Various strategies to comply with Euro 4, 5 and US 2007 are discussed, also in view of engine performance, fuel economy and cooling system load. Recommendations are given for the most suitable approach to comply also in future with emission legislation in Europe and the United States.

Emission standards as proposed in Europe and the United States for heavy duty diesel engines will require a NOx and particulate reduction of more than 90%. This cannot be achieved by internal engine measures alone. Aftertreatment systems, for either one or both emission components, plus sophisticated electronic control strategies will be required. Various strategies to comply with EU 4, 5 and US 2007 are discussed, also showing their impact on engine performance. For typical 1 and 2 liter per cylinder engines, emission reduction concepts are assessed to identify the most suitable technology for major worldwide markets. The assessment is based on thermodynamic studies, test-bed results and estimates on cost and infrastructure implications.

Diesel engines belong to the most efficient power sources for any kind of on-road vehicle, but especially in Europe increasingly for passenger cars. However, more stringent exhaust emission regulations, which will come into force world-wide in industrialised countries during the first decade of the next century will require NOx and particulate emissions to be reduced by up to 60% and more from today's levels. To meet these future emission standards particularly for heavier passenger vehicles, such as SUVs, Pickup Trucks and Light Commercial Vehicles, as well as for heavy luxury class passenger cars, the application of new technologies including advanced exhaust gas aftertreatment systems will be indispensable, especially in view of maintaining the thermal efficiency of diesel engines relative to gasoline engines.

The paper reports on the outcome of a still on-going joint-research project with the objective of establishing a demonstrator high speed direct injection (HSDI) diesel engine in a Sport Utility Vehicle (SUV) which allows to exploit the effectiveness of new engine and aftertreatment technologies for reducing exhaust emissions to future levels of US/EPA Tier 2 and Euro 4. This objective should be accomplished in three major steps: (1) reduce NOx by advanced engine technologies (cooled EGR, flexible high pressure common rail fuel injection system, adapted combustion system), (2) reduce particulates by the Continuous Regeneration Trap (CRT), and (3) reduce NOx further by a DeNOx aftertreatment technology. The current paper presents engine and vehicle results on step (1) and (2), and gives an outlook to step (3).

The paper reports on achievements obtained in an ongoing development program which is part of a european EUREKA joint research project named EFFLED (EFFicient Low Emission Diesel) being performed at AVL in cooperation with the companies DAF Trucks, Serck Heat Transfer, Robert Bosch and the Community of the City of Rotterdam. The main objective of this project is the development and refinement of a venturi supported exhaust gas recirculation (EGR) system for a turbocharged and intercooled heavy-duty (HD) diesel engine enabling map controlled cooled EGR rates which are high enough to achieve future low NOx emission standards at acceptable fuel consumption level. In addition to EGR, further technologies have been investigated, which may be required to meet future exhaust emission standards.

Despite the increasingly stringent emissions legislation, users and owners of commercial diesel vehicles are continually demanding that each new engine generation is more economical than the previous one. This is especially important for commercial vehicles where the majority of engines are in the 1-2ltr./cyl. class. The demands are being reflected in new engine designs with lower friction and improved structural stiffness, together with fuel systems having increased pressure capability, higher spill rates, injection rate shaping and advanced control features. These fuel system requirements have led to a variety of new fuel injection systems and in the search for increased injection pressure these fuel systems have placed greater demands on the engine, especially in areas such as the cylinder head and fuel system drive, sometimes with adverse effects on the combustion and fuel injection system induced mechanical noise.

The influence of fuel density on exhaust emissions from diesel engines has been investigated in a number of studies and these have generally concluded that particulate emissions rise with increasing density This paper reviews recent work in this area, including the European Programme on Emissions, Fuels and Engine Technologies (EPEFE) and reports on a complementary study conducted by CONCAWE, in cooperation with AVL List GmbH The project was carried out with a passenger car equipped with an advanced technology high speed direct injection turbocharged / intercooled diesel engine fitted with a complex engine management system which was referenced to a specific fuel density This production model featured electronic diesel control, closed loop exhaust gas recirculation and an exhaust oxidation catalyst Tests were carried out with two EPEFE fuels which excluded the influence of key fuel properties other than density (828 8 and 855 1 kg/m3) Engine operation was adjusted for changes in fuel density by resetting the electronic programmable, read-only memory to obtain the same energy output from the two test fuels In chassis dynamometer tests over the ECE15 + EUDC test cycle the major impact of fuel density on particulate emissions for advanced engine technology/engine management systems was established A large proportion of the density effect on particulate and NOx emissions was due to physical interaction between fuel density and the electronic engine management system Limited bench engine testing of the basic engine showed that nearly complete compensation of the density effect on smoke (particulate) emissions could be achieved when no advanced technology was applied

This paper reports on research and development work conducted at AVL to determine the NOx-reduction potential of in-cylinder charge conditions, fuel injection system parameters, exhaust gas recirculation, fuel formulation, and exhaust gas aftertreatment by catalyst. Based on these findings, development options are derived and assigned to the various future emission standards in USA, Europe and Japan.